Milwaukee 49-24-0155 User Manual
Cat. No.
No de Cat.
49-24-0155
49-24-0165
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
18 VOLT WORK LIGHT
For use with MILWAUKEE 18 V NiCd or Li-Ion Battery Packs
12 AND14.4 VOLT WORK LIGHT
For use with MILWAUKEE 12 and 14.4V NiCd Battery Packs
LAMPE DE TRAVAIL DE VOLT DE 18
Compatible avec batterie
au LithiumIon ou Nickel-Cadmium 18 V
MILWAUKEE
LAMPE DE TRAVAIL DE VOLT DE 12 ET 14,4
Compatible avec batterie
au Nickel-Cadmium 12 et 14,4 V
MILWAUKEE
LAMPARA DE TRABAJO DEL VOLTIO 18
Compatible con
batería de iones de litio y Niquel-Cadmio de 18V de
MILWAUKEE
LAMPARA DE TRABAJO DEL VOLTIO 12 y 14,4
Compatible con
TO REDUCE THE RISK OF INJURY, USER MUST READ OPERATOR'S MANUAL.
AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE LE
MANUEL DE L'UTILISATEUR.
PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER EL MANUAL
DEL OPERADOR.
batería de Niquel-Cadmio de 12 y 14.4 V de
MILWAUKEE
IMPORTANT SAFETY INSTRUCTIONS
WARNING
When using electric appliances, basic precautions should always be followed,
including the following:
Before using the work light, read this operator's manual, your battery pack and charger
operator's manual, and all labels on the battery pack, charger and work light.
• Read all the instructions before using
the appliance.
• To reduce the risk of injury , close supervision is necessary when an appliance is
used near children.
• Do not use outdoors.
• For a rechargeable appliance - Use only
the charger supplied by the manufacturer
to recharge.
• For an appliance with a replaceable
lamp - always unplug before replacing the
lamp. See "Specifi cations" for replacement
bulbs.
• Know your work light. Read this manual
carefully to learn your work light's applications and limitations as well as potential
hazards associated with this type of tool.
• Batteries must be recharged only with
the specifi ed charger for the battery. A
charger that may be suitable for one type
of battery may create a risk of fi re when
used with another battery.
• Use work light only with specifi cally
designated battery pack. Use of any
other batteries may create a risk of fi re.
READ AND UNDERSTAND ALL INSTRUCTIONS.
• When battery pack is not in use, keep
it away from metal objects like: paper
clips, coins, keys, nails, screws, or
other small metal objects that can
make a connection from one terminal
to another. Shorting the battery terminals
together may cause sparks, burns, or a
fi re.
• Never insert bulbs other than
MILWAUKEE bulbs in the bulb socket.
Bulbs other than MILWAUKEE bulbs
may cause short circuit of battery and
personal injury.
• Store idle work light out of reach
of children. Warm work lights can
become hazardous in the hands of children.
• Maintain labels and nameplates.
These carry important information.
If unreadable or missing, contact a
MILWAUKEE service facility for a free
replacement.
SAVE THESE
INSTRUCTIONS
Symbology
Volts Direct Current
Cat. No.
49-24-0155
49-24-0165
Specifi cations
Volts DC
12 or 14.4
18
Underwriters Laboratories, Inc.
Replacement Bulbs
49-81-0020
49-81-0030
ASSEMBLY
Removing Battery Pack from Tool
Push in the release buttons and pull the
battery pack away from the tool.
Inserting Battery Pack into Tool
T o insert the battery pack onto the tool, slide
the pack onto the body of the tool. Make sure
it latches securely into place.
WARNING
To reduce the risk of injury, do not
look directly into the light when the
work light is on.
Adjusting the pivot head
The pivot head can pivot to a range of 140°;
110° up and 30° down with detents every
10°. Pivot head to desired position (Fig. 1).
Allow the detent to snap into place. Do not
forcibly pivot the head.
Fig. 1
WARNING
To reduce the risk of injury, DO
NOT operate work light without
bezel assembly in place. Bulb does
get hot. Always remove battery
pack before changing or removing
bulbs. Always allow the work light to
cool for at least 10 minutes before
replacing the bulb.
Replacing the Bulb
1. Remove battery pack before changing
bulb.
2. Unscrew the bezel assembly on pivot
head by turning counterclockwise.
3. Remove the bezel assembly.
4. Pull forward the aluminum heat sink.
5. Gently rotate the bulb counter clockwise
and pull out.
Fig. 2
Bezel
assembly
Spare bulb storage
Pivot
head
Bulb
Aluminum
heat sink
WARNING
To reduce the risk of injury and
damage, never insert bulbs other
than MILWAUKEE bulbs in the bulb
socket.
To install new bulb, follow above directions
in reverse.
NOTE: Use a soft cloth when installing bulbs.
Direct contact with oils or other contamination can shorten the life of bulbs.
For work light 49-24-0155, use replacement
bulb 49-81-0020.
For work light 49-24-0165, use replacement
bulb 49-81-0030.
A spare bulb is provided with the work
light. The bulb is located behind the
aluminum heat sink.
See your nearest MILWAUKEE Retailer
or Service Center to obtain replacement
bulbs.
2 3
Loading...