
Cat. No. / No de cat.
49-16-3697
BIT HOLDER
PORTE-EMBOUTS
PORTAPUNTAS
(For use with M18™ only)
(À utiliser avec M18™ uniquement)
(Para su uso exclusivo con M18™)
IMPORTANT SAFETY
INSTRUCTIONS
READ ALL SAFETY WARNINGS,
TIONS AND SPECIFICATIONS PROVIDED
WITH THIS PRODUCT AND ANY POWER
TOOLS TO BE USED WITH THIS KIT. Failure
to follow all instructions listed below may result
in electric shock, re and/or serious injury.
SAVE THESE INSTRUCTIONS - THIS OPERATOR’S MANUAL CONTAINS IMPORTANT
SAFETY AND OPERATING INSTRUCTIONS.
injury.
INSTRUCTIONS, ILLUSTRA-
Not for use with tethered tools.
Bits could disengage and cause
ASSEMBLY
To reduce the risk of injury, al-
making any adjustments or changing accessories. Only use accessories specically recommended for this tool. Others may be hazardous.
1. Kit includes Bit Holder, M12™ Adapter, M12™
Screw (Long), M18™ Screw (Short).
2. Remove battery pack.
3. Can be installed on either side of tool. Remove/
move belt clip if necessary.
4. Hand tighten screw securely (as shown in image
above). Do NOT use power tool.
Bit Holder will hold 1/4" hex shank bits. Insert bit(s)
fully into the holder.
ways remove battery pack before
Installing Bit Holder
(For use with M12™ only)
(À utiliser avec M12™ uniquement)
(Para su uso exclusivo con M2™)
INSTRUCTIONS IMPORTANTES
CONCERNANT LA SÉCURITÉ
CONSULTER TOUS LES
SÉCURITÉ, TOUTES LES INSTRUCTIONS,
TOUTES LES ILLUSTRATIONS ET TOUTES LES
SPÉCIFICATIONS FOURNIES AVEC CE PRODUIT
ET TOUT AUTRE OUTIL ÉLECTRIQUE QUI SERA
UTILISÉ AVEC CET ENSEMBLE. Le non-respect
de toutes les instructions ci-dessous peut en-
traîner un choc électrique, un incendie et/ou des
blessures graves. GARDER CES INSTRUCTIONS. LE MANUEL D’UTILISATION CONTIENT
D’IMPORTANTES INSTRUCTIONS DE SÉCURITÉ
ET DE FONCTIONNEMENT.
pointes pourraient se désengager et causer des
blessures.
AVERTISSEMENTS DE
Ne pas utiliser jumelé à
des outils fixés. Les
ASSEMBLAGE
An de minimiser le ris-
jours retirer le bloc-piles avant d’entreprendre
tout ajustement ou de changer les accessoires.
Utiliser uniquement des accessoires spéciale-
ment recommandés pour cet outil. En utiliser
d’autres pourra poser un danger.
Installation du porte-embouts
1. L’ensemble comprend le porte-embouts,
l’adaptateur M12™, la vis M12™ (longue), la vis
M18™ (courte).
2. Retirer le bloc-piles.
3. Il est possible de l’installer dans n’importe quel
côté de l’outil. Retirer/bouger le clip de ceinture
si nécessaire.
4. Bien serrer la vis à la main (comme illustré
dans l’image ci-dessus). NE PAS utiliser un outil
électrique.
Le porte-embout soutiendra des tiges hexagonales
de 6 mm (1/4"). Insérer l’embout ou les embouts
dans le porte-embouts.
que de blessures, tou-

INSTRUCCIONES DE SEGURIDAD
IMPORTANTES
CONSULTE TODAS LAS
RIDAD, LAS INSTRUCCIONES, LAS ILUSTRACIONES Y LAS ESPECIFICACIONES QUE
ACOMPAÑAN ESTE PRODUCTO, ASÍ COMO LAS
HERRAMIENTAS ELÉCTRICAS QUE SE UTILICEN
CON ESTE JUEGO. No seguir todas las instruc-
ciones que se enumeran a continuación podría
provocar una descarga eléctrica, incendio o
lesiones personales graves. GUARDE ESTAS
INSTRUCCIONES. EL MANUAL DEL OPERADOR
CONTIENE INSTRUCCIONES IMPORTANTES DE
SEGURIDAD Y OPERACIÓN.
drían desengancharse y provocar lesiones.
ADVERTENCIAS DE SEGU-
No se utilice con herramientas jadas. Las puntas po-
ENSAMBLADO
Para reducir el riesgo de
batería antes de realizar algún ajuste o cambiar
los accesorios. Utilice únicamente accesorios
especícamente recomendados para esta herramienta. Utilizar otros accesorios podrá ser
peligroso.
1. El juego incluye el portapuntas, el adaptador
2. Quite la batería.
3. Puede instalarse en cualquiera de los lados de
4. Apriete rmemente el tornillo con la mano (tal
El portapuntas sostendrá las espigas hexagonales
de 6 mm (1/4"). Inserte la o las puntas hasta el fondo
del portapuntas.
Instalación del portapuntas
M12™, el tornillo M12™ (largo), tornillo M18™
(corto).
la herramienta. Quite/mueva el gancho para
cinturón de ser necesario.
como se muestra en la imagen). NO utilice ningún
tipo de herramienta eléctrica.
lesión, siempre retire la
58223697d1 11/21 961014398-01(A)
Printed in
13135 West Lisbon Road • Brookeld, WI 53005 USA
MILWAUKEE TOOL