Milwaukee Tool 48-59-2819 User Manual [en, es, fr]
New battery packs must be charged
before fi rst use.
Les batteries neuves doivent être
chargées avant leur utilisation initiale.
Las baterías nuevas se deben cargar
antes de usarlas por primera vez.
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
Cat. No.
No de Cat.
48-59-2819
Cat. No.
No de Cat.
48-11-2830
M28™ & V28® LITHIUM-ION BATTERY CHARGER
M28™ LITHIUM-ION BATTERY PACKS
CHARGEURS AU LITHIUM-ION M28™ ET V28®
BATTERIE AU LITHIUM-ION M28
CARGADORS PARA BATERÍAS DE IONES DE LITIO DE M28™ Y V28
BATERÍA DE IONES DE LITIO DE M28
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S
MANUAL.
AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN
COMPRENDRE LE MANUEL DE L'UTILISATEUR.
PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL
MANUAL DEL OPERADOR.
™
®
™
IMPORTANT SAFETY INSTRUCTIONS
WARNING READ AND UNDERST AND ALL INSTRUCTIONS. Failure to follow all
instructions listed below, may result in electric shock, fi re and/or serious personal injury.
SAVE THESE INSTRUCTIONS
1. SAVE THESE INSTRUCTIONS - THIS OP-
ERAT OR’S MANUAL CONT AINS IMPORT ANT
SAFETY AND OPERATING INSTRUCTIONS
FOR MILWAUKEE LI-ION BATTERY PACKS
AND THE MILWAUKEE LI-ION CHARGER.
2. BEFORE USING THE BATTERY PACK AND
CHARGER, READ THIS OPERATOR’S MANUAL, YOUR TOOL OPERATOR’S MANUAL,
AND ALL LABELS ON THE BATTERY P ACK,
CHARGER AND TOOL.
3. CAUTION - TO REDUCE THE RISK OF INJURY ,
CHARGE MILW AUKEE 28 VOL T LITHIUM-ION
PACKS ONLY IN THIS MILWAUKEE 28 VOLT
LITHIUM-ION CHARGER. Other types of
chargers may cause personal injury or damage.
Do not wire a battery pack to a power supply
plug or car cigarette lighter. Battery packs will
be permanently disabled or damaged.
4. USE MILWAUKEE M28
IUM-ION PACKS ONLY ON COMPATIBLE
MILWAUKEE M28™ AND V28® LITHIUM-ION
TOOLS. Use with other tools may result in a risk
of fi re, electric shock or personal injury.
5. AVOID DANGEROUS ENVIRONMENTS. Do not
charge battery pack in rain, snow, damp or wet
locations. Do not use battery pack or charger in
the presence of explosive atmospheres (gaseous
fumes, dust or fl ammable materials) because
sparks may be generated when inserting or
removing battery pack, possibly causing fi re.
6. CHARGE IN A WELL VENTILATED AREA.
Do not block charger vents. Keep them clear to
allow proper ventilation. Do not allow smoking
or open fl ames near a charging battery pack.
Vented gases may explode.
7. CHARGER IS RATED FOR 120 VOLT AC
ONLY. Charger must be plugged into an ap-
propriate receptacle.
8. MAINTAIN CHARGER CORD. When unplugging charger, pull plug rather than cord to reduce
the risk of damage to the electrical plug and cord.
Never carry charger by its cord. Keep cord from
heat, oil and sharp edges. Make sure cord will
not be stepped on, tripped over or subjected
to damage or stress. Do not use charger with
damaged cord or plug. Have a damaged charger
replaced immediately.
9. DO NOT USE AN EXTENSION CORD UNLESS
IT IS ABSOLUTELY NECESSARY. Using the
wrong, damaged or improperly wired extension
cord could result in the risk of fi re and electrical
shock. If an extension cord must be used, plug
the charger into a properly wired 16 gauge or
larger extension cord with pins that are the
same number, size and shape as the pins on
™
AND V28® LITH-
the charger. Make sure that the extension cord
is in good electrical condition.
10. USE ONL Y RECOMMENDED A TTACHMENTS.
Use of an attachment not recommended or sold
by the battery charger or battery pack manufacturer may result in a risk of fi re, electric shock
or personal injury.
11. UNPLUG CHARGER when not in use. Remove
battery packs from unplugged chargers.
12. TO REDUCE THE RISK OF ELECTRIC
SHOCK, always unplug charger before clean-
ing or maintenance. Use a Ground Fault Circuit
Interrupter (GFCI) to reduce shock hazards.
13. DO NOT BURN OR INCINERATE BATTERY
PACKS. Battery packs may explode, causing per-
sonal injury or damage. T oxic fumes and materials
are created when battery packs are burned.
14. DO NOT CRUSH, DROP, OR DAMAGE battery
pack. Do not use a battery pack or charger that
has received a sharp blow, been dropped, run
over, or damaged in any way (e.g., pierced with
a nail, hit with a hammer, stepped on).
15. DO NOT DISASSEMBLE. Incorrect reassembly
may result in the risk of electric shock, fi re or
exposure to battery chemicals. If it is damaged,
take it to a MILWAUKEE service facility.
16. BATTERY CHEMICALS CAUSE SERIOUS
BURNS. Never allow contact with skin, eyes, or
mouth. If a damaged battery pack leaks battery
chemicals, use rubber or neoprene gloves to
dispose of it. If skin is exposed to battery fl uids,
wash with soap and water and rinse with vinegar. If eyes are exposed to battery chemicals,
immediately fl ush with water for 20 minutes and
seek medical attention. Remove and dispose of
contaminated clothing.
17. DO NOT SHORT CIRCUIT. A battery pack will
short circuit if a metal object makes a connection between the positive and negative contacts
on the battery pack. Do not place a battery pack
near anything that may cause a short circuit,
such as coins, keys or nails in your pocket. A
short circuited battery pack may cause fi re and
personal injury.
18. STORE YOUR BATTERY PACK AND CHARGER in a cool, dry place. Do not store battery
pack where temperatures may exceed 120°F
(50°C) such as in direct sunlight, a vehicle or
metal building during the summer.
READ AND SAVE ALL
INSTRUCTIONS FOR
FUTURE REFERENCE.
2
SPECIFICATIONS
Charger
Cat. No.
48-59-2819* 120 1.5 28 3.5
* Charges MILWAUKEE 48-11-2830 M28™ and
48-11-2830 V28
Battery
Cat. No.
48-11-2830 28 1-Hour
AC Input
AC Input
Volts
Amps
®
Li-Ion battery packs.
DC Volts
Charge
Time
DC Output
Volts
DC Output
Amps
SYMBOLOGY
Volts
Direct Current
Alternating Current
Double Insulated
Hertz
Amps
Properly Recycle Batteries
Underwriters Laboratories, Inc.
United States and Canada
FUNCTIONAL DESCRIPTION
8
7
1. Contacts
2. Release buttons
3. Fuel Gauge button
4. Fuel Gauge
5. Electrical contacts
6. Bay
7. Vents
8. Light indicators - when a battery pack is inserted into
the charger, the light will indicate the following:
Continuous red: Charging
Continuous green light: Charging is complete
Flashing red: Battery is too hot/cold - Charging will
begin when battery reaches correct
charging temperature
Flashing red/green: Damaged or faulty battery pack
3
2
4
3
5
6
1
2
MILWAUKEE LITHIUM-ION BATTERY PACK OPERATION
Fuel Gauge
Use the Fuel Gauge to determine the battery pack's
remaining run time. Press the Fuel Gauge button
to display the lights. The Fuel Gauge will stay lit for
two seconds.
NOTE: If the Fuel Gauge
doesn't appear to be
working, place the battery pack on the charger
and charge as needed.
Compared to NiCd
battery pack types,
MILWAUKEE Lithium-Ion battery packs deliver
fade-free power for their entire run time. The tool
will not experience a slow, gradual loss of power
as you work. To signal to you that the battery
pack is at the end of its run time and needs to be
charged, power to the tool will drop quickly. When
this happens, remove the tool from the workpiece
and charge the battery pack as needed.
NOTE: Immediately after using the battery pack,
the Fuel Gauge may display a lower charge than it
will if checked a few minutes later. The battery cells
"recover" some of their charge after resting.
Battery Pack Protection
To protect itself from damage and extend its life,
the battery pack’s intelligent circuit monitors current
draw and temperature.
In extremely high torque, binding, stalling, and short
circuit situations, the battery pack will turn OFF the
tool if the current draw becomes too high. In these
situations, the tool may “buzz” for about 2 seconds
before it turns OFF . To prevent the tool from turning
OFF , immediately reduce pressure on the application or release the trigger. If the tool does turn off,
the Fuel Gauge lights will fl ash 8 times. Release
the trigger to reset.
Under extreme circumstances, the internal temperature of the battery could become too high. If
this happens, the battery pack will shut off. When
the Fuel Gauge button is pressed, the lights will
fl ash alternatingly. Allow the battery pack to cool.
The battery is ready for use when the Fuel Gauge
displays the remaining run time when the Fuel
Gauge button is pressed.
Cold Weather Operation
MILWAUKEE Lithium-Ion battery packs are designed to operate in temperatures below freezing.
When the battery pack is too cold, it may need to
warm up before normal use. Put the battery on a
tool and use the tool in a light application. It may
“buzz” for a short time until it warms up. When the
buzzing stops, use the tool normally.
Approximate Run
Time Remaining
33-54%
10-32%
<10% - 1st light will fl ash 4X
0% - 1st light will fl ash 8X
78-100%
55-77%
Maintenance and Storage
Do not expose your battery pack or cordless tools
to water or rain, or allow them to get wet. This could
damage the tool and battery pack. Do not use oil
or solvents to clean or lubricate your battery pack.
The plastic casing will become brittle and crack,
causing a risk of injury.
Store battery packs at room temperature away from
moisture. Do not store in damp locations where corrosion of terminals may occur. As with other battery
pack types, permanent capacity loss can result if
the pack is stored for long periods of time at high
temperatures (over 120° F). MILWAUKEE Lithium-
Ion battery packs maintain their charge during
storage longer than other battery pack types. After
about a year of storage, charge the pack as normal.
Disposing of MILWAUKEE Li-Ion Battery Packs
MILWAUKEE Lithium-Ion battery packs are more
environmentally friendly than some other types of
power tool battery packs (e.g., nickel-cadmium).
Always dispose of your battery pack according to
federal, state and local regulations. Contact a recycling agency in your area for recycling locations.
Even discharged battery packs contain some energy. Before disposing, use electrical tape to cover
the terminals to prevent the battery pack from shorting, which could cause a fi re or explosion.
WARNING To reduce the risk of in-
jury or explosion, never burn or incinerate
a battery pack even if it is damaged, dead or
completely discharged. When burned, toxic
fumes and materials are created.
RBRC Battery Recycling Seals
The RBRC™ Battery Recycling Seals (see "Symbology") on your tool battery packs indicate that
MILWAUKEE has arranged for the recycling of
that battery pack with the Rechargeable Battery
Recycling Corporation (RBRC). At the end of your
battery pack's useful life, return the battery pack to
a MILWAUKEE Branch Offi ce/Service Center or the
participating retailer nearest you. For more informa-
tion, visit the RBRC web site at www.rbrc.org.
CHARGER OPERATION
WARNING Charge only
MILWAUKEE 28 Volt Lithium-Ion battery
packs in MILWAUKEE 28 Volt Li-Ion Battery
Chargers. Other types of batteries may cause
personal injury and damage.
When to Charge the Battery Packs
Remove the battery pack from the tool for
charging when convenient for you and your job.
MILWAUKEE battery packs do not develop a
"memory" when charged after only a partial discharge. It is not necessary to run down the battery
pack before placing it on the charger.
• Use the Fuel Gauge to determine when to charge
your MILWAUKEE Li-Ion battery pack.
• You can "Top-Off" your battery pack's charge
before starting a big job or long day of use.
• The only time it is necessary to charge the
MILWAUKEE Lithium-Ion battery pack is when
the pack has reached the end of its charge. To
signal the end of charge, power to the tool will drop
quickly, allowing you just enough power to fi nish
making a cut, drilling a hole, or driving a fastener.
Charge the battery pack as needed.
How to Charge the Battery Packs
Place the battery pack onto the bay by sliding the
pack on from the top of the bay. The red light will
turn on, either fl ashing (pack is too hot or cold) or
continuous (pack is charging).
• A fully discharged pack with an internal temperature between 32°F and 150°F will charge in about
1-Hour.
• Heavily cycled battery packs may take longer to
charge completely.
• The Fuel Gauge lights on the battery pack are
displayed as the pack is being charged, indicating
how fully charged the pack is.
• After charging is complete, the continuous green
light will turn on and the fuel gauge will turn off.
• The charger will keep the battery pack fully
charged if it is left on the charger.
• If the light indicator fl ashes red and green, check
that the battery pack is fully seated into the bay.
Remove the pack and reinsert. If the problem
persists, contact a MILWAUKEE service facility.
• If the light indicator does not come on, check
that the battery pack is fully seated into the bay.
Remove the pack and reinsert. If the light indicator
still does not come on, contact a MILWAUKEE
service facility.
Charging Hot or Cold Battery Packs
The Red fl ashing indicator light on the charger indi-
cates that the battery pack temperature is outside
the charging range. Once the pack is within the
acceptable range, normal charging will take place
and the red light will be continuous. Hot or cold
battery packs may take longer to charge.
Battery Pack
Temperature
Too Hot / Too Cold Flashing Not charging
Normal Range Continuous Normal charging
Red Charger
Indicator Light
Charging
Status
Powering the Charger with an Inverter or
Generator
The charger will operate with most generators and
inverters rated at 300 Watts or higher.
Maintenance and Storage
Store your charger in a cool, dry place.
As a general practice, it is best to unplug battery
chargers and remove battery packs when not in
use. No battery pack damage will occur, however , if
the charger and battery pack are left plugged in.
WARNING To reduce the risk of in-
jury, always unplug the charger and remove
the battery pack from the charger before
performing any maintenance. Never disassemble the battery pack or charger. Contact
a MILWAUKEE service facility for ALL repairs.
To reduce the risk of injury and damage, never
immerse your battery pack or charger in liquid
or allow a liquid to fl ow inside them.
Cleaning
Clean out dust and debris from charger vents and
electrical contacts by blowing with compressed air.
Use only mild soap and a damp cloth to clean the
battery pack and charger, keeping away from all electrical contacts. Certain cleaning agents and solvents
are harmful to plastics and other insulated parts.
Some of these include gasoline, turpentine, lacquer
thinner, paint thinner, chlorinated cleaning solvents,
ammonia and household detergents containing ammonia. Never use fl ammable or combustible solvents
around battery packs, charger, or tools.
Repairs
The MILWAUKEE Li-Ion charger has no serviceable parts.
4
5
LIMITED WARRANTY - USA AND CANADA
Every MILWAUKEE Battery Pack (sold with cordless product and/or as a replacement battery pack) is warranted to the
original purchaser only to be free from defects in material and workmanship. Subject to certain exceptions, MILWAUKEE
will repair or replace a battery pack which, after examination, is determined by MILWAUKEE to be defective in material
or workmanship for the stated warranty period from date of purchase. Return of the battery pack to a MILWAUKEE
factory Service Center location or MILWAUKEE Authorized Service Station, freight prepaid and insured, is required.
A copy of the proof of purchase should be included with the return product. This warranty does not apply to damage
that MILWAUKEE determines to be from repairs made or attempted by anyone other than MILWAUKEE authorized
personnel, misuse, alterations, abuse, normal wear and tear, lack of maintenance, or accidents.
Battery Pack Description Chemistry Warranty Period (from date of purchase)
M12™ XC REDLITHIUM™
M12™ XC REDLITHIUM™ 4.0
M18™ XC REDLITHIUM™
M18™ XC REDLITHIUM™ 4.0
M28™ XC LITHIUM-ION
M28™ XC REDLITHIUM™
V4 LITHIUM-ION
M12™ Compact LITHIUM-ION
M12™ Compact REDLITHIUM™
M12™ Compact REDLITHIUM™ 2.0
M12™ XC LITHIUM-ION
M18™ Compact LITHIUM-ION
M18™ Compact REDLITHIUM™
M18™ Compact REDLITHIUM™ 2.0
M18™ LITHIUM-ION
V18™ V™-technology LITHIUM-ION Serial number prefix “A95”
V28™ V™-technology LITHIUM-ION
Ni-Cd, Ni-Cd Super-Tough, Ni-Cd PowerPlus, Ni-MH, V18™ V™-technology
LITHIUM-ION Serial number prefix “E95”
The warranty period for all Ni-CD and Ni-MH Battery Packs is one (1) year from the date of purchase. The warranty period
for V4 Lithium-Ion, M12™ Compact Lithium-ion, M12™ Compact REDLITHIUM™, M12™ XC LITHIUM-ION, M18™
Compact LITHIUM-ION and M18™Compact REDLITHIUM™ Battery Packs is two (2) years from the date of purchase.
The warranty period for M12™ XC REDLITHIUM™, M18™ XC REDLITHIUM™, M28™ XC REDLITHIUM™ and
M28™ XC LITHIUM-ION Battery Packs is three (3) years from the date of purchase. *The warranty period for every
MILWAUKEE V™-technology V28™ LITHIUM-ION Battery Pack, M18™ XC HIGH CAPACITY LITHIUM-ION Battery
Pack, and V™-technology V18™ LITHIUM-ION Battery Pack (with the serial number prefix “A95”) is five (5) years /
2000 charges from the date of purchase, whichever first occurs. The first 1000 charges or 2 years of the warranty,
whichever first occurs, are covered through free replacement of the defective battery. This means that for the earlier of
the first 1000 charges or two (2) years from the date of purchase/first charge, a replacement battery will be provided
to the customer for any defective battery free of charge. Thereafter, the remaining charges up to a total of 2000 or the
remainder of the five (5) year period from the date of purchase, whichever first occurs, will be covered on a pro rata basis.
This means that every customer gets an additional 1000 charges or three (3) years of pro rata warranty on the
V™technology V28™ LITHIUM-ION Battery Pack, M18™ XC LITHIUM-ION Battery Pack, and V™-technology V18™
LITHIUM-ION Battery Pack (with the serial number prefix “A95”) depending upon the amount of use. The warranty
period for V™-technology V18™ LITHIUM-ION Battery Pack (with the serial number prefix “E95”) is one (1) year.
Warranty Registration is not necessary to obtain the applicable warranty on a MILWAUKEE battery pack. The
manufacturing date of the product will be used to determine the warranty period if no proof of purchase is provided at
the time warranty service is requested.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT. IF YOU DO NOT AGREE
TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE BE
LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR ANY COSTS,
ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE
TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS
OF PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMIT ATION OR EXCLUSION MA Y NOT APPL Y TO YOU. THIS WARRANTY
IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRITTEN OR ORAL. TO THE EXTENT
PERMITTED BY LAW , MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMIT A TION
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR PURPOSE; TO
THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WARRANTIES ARE LIMITED TO
THE DURATION OF THE APPLICABLE EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES DO NOT
ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT
APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
Please consult the ‘Service Center Search’ in the Parts & Service section of MILWAUKEE’s website
www.milwaukeetool.com or call 1.800.SAWDUST (1.800.729.3878) to locate your nearest service facility for warranty
and non-warranty service on a MILWAUKEE Cordless Battery Pack.
LITHIUM-ION Three (3) Years
LITHIUM-ION Two (2) Years
LITHIUM-ION
Ni-Cd / Nickel-Cadmium,
Ni-MH / Nickel-Metal-Hydride
LITHIUM-ION
Three (3) Years Pro-Rata (prorated)*
6
Two (2) Years – plus,
One (1) Year
LIMITED WARRANTY - USA AND CANADA
Every MILWAUKEE power tool (including cordless product – tool, battery pack(s) - see separate & distinct
CORDLESS BATTERY PACK LIMITED WARRANTY statements & battery charger and Work Lights*) is warranted to the original purchaser only to be free from defects in material and workmanship. Subject to certain
exceptions, MILWAUKEE will repair or replace any part on an electric power tool which, after examination, is
determined by MILWAUKEE to be defective in material or workmanship for a period of fi ve (5) years* after the
date of purchase unless otherwise noted. Return of the power tool to a MILWAUKEE factory Service Center
location or MILWAUKEE Authorized Service Station, freight prepaid and insured, is required. A copy of the
proof of purchase should be included with the return product. This warranty does not apply to damage that
MILWAUKEE determines to be from repairs made or attempted by anyone other than MILWAUKEE authorized
personnel, misuse, alterations, abuse, normal wear and tear, lack of maintenance, or accidents.
*The warranty period for, Job Site Radios, M12™ Power Port, M18™ Power Source, and T rade T itan™ Industrial Work Carts is one (1) year from the date of purchase. The warranty period for a LED Work Light and LED
Upgrade Bulb is a limited LIFETIME warranty to the original purchaser only, if during normal use the LED bulb
fails the Work Light or Upgrade Bulb will be replaced free of charge.
*This warranty does not cover Air Nailers & Stapler, Airless Paint Sprayer, Cordless Battery Packs, Gasoline
Driven Portable Power Generators, Hand Tools, Hoist – Electric, Lever & Hand Chain, M12™ Heated Jackets,
Reconditioned product and Test & Measurement products. There are separate and distinct warranties available for these products.
Warranty Registration is not necessary to obtain the applicable warranty on a MILWAUKEE power tool product.
The manufacturing date of the product will be used to determine the warranty period if no proof of purchase is
provided at the time warranty service is requested.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN IS A
CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT . IF YOU DO NOT
AGREE TO THIS CONDITION, YOU SHOULD NOT PURCHASE THE PRODUCT. IN NO EVENT SHALL MIL-
WAUKEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL OR PUNITIVE DAMAGES, OR FOR
ANY COSTS, ATTORNEY FEES, EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE
OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY
CLAIMS FOR LOSS OF PROFITS. SOME STA TES DO NOT ALLOW THE EXCLUSION OR LIMIT A TION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMIT A TION OR EXCLUSION MA Y NOT APPL Y
TO YOU. THIS W ARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRANTIES, WRITTEN
OR ORAL. TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS ANY IMPLIED WARRANTIES,
INCLUDING WITHOUT LIMIT A TION ANY IMPLIED W ARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PAR TICULAR USE OR PURPOSE; TO THE EXTENT SUCH DISCLAIMER IS NOT PERMITTED BY LAW , SUCH
IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE EXPRESS W ARRANTY AS
DESCRIBED ABOVE. SOME ST A TES DO NOT ALLOW LIMITA TIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
Please consult the ‘Service Center Search’ in the Parts & Service section of MILWAUKEE’s website www.mil-
waukeetool.com or call 1.800.SAWDUST (1.800.729.3878) to locate your nearest service facility for warranty
and non-warranty service on a Milwaukee electric power tool.
LIMITED WARRANTY - MEXICO, CENTRAL AMERICA AND CARIBBEAN
TECHTRONIC INDUSTRIES' warranty is for 5 year since the original purchase date.
This warranty card covers any defect in material and workmanship on this Power Tool.
To make this warranty valid, present this warranty card, sealed/stamped by the distributor or store where you purchased the product, to the Authorized Service Center (ASC). Or , if this card has not been sealed/stamped, present the
original proof of purchase to the ASC.
Call toll-free 1 800 832 1949 to fi nd the nearest ASC, for service, parts, accessories or components.
Procedure to make this warranty valid
Take the product to the ASC, along with the warranty card sealed/stamped by the distributor or store where you purchased the product, and there any faulty piece or component will be replaced without cost for you. We will cover all
freight costs relative with this warranty process.
Exceptions
This warranty is not valid in the following situations:
a) When the product is used in a different manners from the end-user guide or instruction manual.
b) When the conditions of use are not normal.
c) When the product was modifi ed or repaired by people not authorized by TECHTRONIC INDUSTRIES.
Note: If cord set is damaged, it should be replaced by an Authorized Service Center to avoid electric risks.
SERVICE AND ATTENTION CENTER
Model:
Rafael Buelna No.1.
Col. Tezozomoc Mexico, Azcapotzalco D.F.
Date of Purchase:
Ph. 01 800 832 1949
Distributor or Store Stamp:
IMPORTED AND COMMERCIALIZED BY:
TECHTRONIC INDUSTRIES MEXICO, .S.A. DE C.V.
Av. Santa Fe 481 piso 6, Col. Curz Manca.
CP 05349, Cuajimalpa, D.F.
7
Loading...