EXAMPLE:
00
Component Parts (Small #) Are Included
0
When Ordering The Assembly (Large #).
16 17
60
18 19
25
(4x)
22
14
(4x)
19
18
17
54
53
65
SERVICE PARTS LIST
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
M18 FUEL™ Flat Head Braking Angle Grinder w/ Paddle Switch
35 43
44
44
62
STARTING
SERIAL NO.
2 4 10
63
47 57
2
1
L72A
48
4
5
CATALOG NO.
66
22
35
(2x)
16
2886-20
35
61
37
35
(2x)
43
BULLETIN NO.
54-38-2350
REVISED BULLETIN
WIRING INSTRUCTION
SEE PAGE 2
5
64
47
58
DATE
May 2022
57
10
(5x)
11
56
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 31-15-0103 Dust Cover (1)
2 --------------- Left Housing Halve-Support (1)
4 --------------- Right Housing Halve-Cover (1)
5 40-50-0243 Spring (1)
10 06-82-2025 M3.5 x 16mm Pan Hd. ST T-10 Screw (5)
11 44-40-7100 5/8" Flange Nut (1)
14 05-74-0302 M4 x 8mm Flat Hd. T-20 Macine Screw (4)
16 05-74-0301 M3 x 12mm Cap Hd. Shoulder Scr. w/Hex (1)
17 40-50-0456 Spring (1)
18 45-04-0031 M3 x 8.5mm Pan Washer Hd. Phillips Screw (1)
19 44-10-0137 Wheel Guard Locking Lever (1)
22 34-40-0266 O-Ring (1)
25 05-88-1255 M4 x 22mm Pan Hd. ST T-20 Screw (4)
35 06-82-2660 M3.5 x 8mm Pan Hd. Taptite T-10 Screw (4)
37 42-90-0024 Plastic Coupler (1)
43 45-88-0241 Flat Washer (1)
44 02-04-0111 Ball Bearing (1)
47 06-82-1087 M3 x 12mm Pan Hd. ST T-10 Screw (1)
48 43-84-0207 Rapid Stop Plate (1)
53 14-34-0109 Side Handle Assembly (1)
54 28-41-0106 5" Type 27 Wheel Guard Assembly (1)
28-41-0105 5" Type 1 Cutting Guard (Not Shown) (1)
56 49-96-7215 Spanner Wrench (1)
57 12-20-0368 Service Nameplate (1)
58 50-55-3560 Contractor Bag (1)
60 14-29-0097 Gearcase Assembly (1)
61 16-01-0116 Rotor Assembly (1)
62 14-20-0196 Electronic Assembly (1)
63 14-38-0104 Housing Kit (1)
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
64 31-92-0256 Paddle Trigger Assembly (1)
65 28-53-0096 Spindle Hub Assembly (1)
66 42-90-0068 Pinion/Coupler Assembly (1)
*LUBRICATION NOTE:
When servicing the Gear Case Assembly,
90-95% of the old grease must be removed
prior to new grease being added.
FIG. LUBRICATION*
65,66 Type ‘S2’ Grease, No. 49-08-5262,
1.4 oz. / 40g tube.
Apply 5g of ‘S2’ grease TOTAL. Coat all
bevel gear and bevel pinion teeth liberally.
Place remaining grease in gearcase cavity.
MILWAUKEE TOOL l www.milwaukeetool.com
13135 W. Lisbon Road, Brookeld, WI 53005
Bevel Gear
Bevel Pinion
Drwg. 2
Ground
Wire
Terminal
15
3 4
2
Battery
Terminal
Block
1 5
On-Off
Switch
Hall Board
Shown without stator
8 7 6
Power Control Board
Wire Color Orientation
1 Red From Hall Board to Power Control Board
2 Pink From Hall Board to Power Control Board
3 Blue From Hall Board to Power Control Board
4 Yellow From Hall Board to Power Control Board
5 Black From Hall Board to Power Control Board
6 White From Power Control Board to Stator
7 Red From Power Control Board to Stator
8 Black From Power Control Board to Stator
9 Yellow From Power Control Board to On-O Switch
10 Yellow From Power Control Board to On-O Switch
11 Red From Power Control Board to Fuse
12 Red From Battery Terminal Block to Fuse
13 Blue From Power Control Board to Battery Terminal Block
14 Green From Power Control Board to Battery Terminal Block
15 Black HV Wire. From Battery Terminal Block to Gearcase
16 Black From Power Control Board to Battery Terminal Block
15
10
9
12
16
1314
11
Fuse
As an aid to reassembly, take notice of wire routing and position in
wire guides and traps while dismantling tool.
Be sure that all components of the electronics kit are seated rmly
and squarely in the housing recesses.
Avoid pinched wires, be sure that all wires and sleeves are pressed
completely down in wire guides and traps.
Prior to securing the housing cover onto the housing support, be
sure that there are no interferences.
Before installing the battery, check for proper functionality of paddle
trigger.
Install battery and depress paddle trigger to assure tool is operating
properly.
Loading...