Milwaukee 2775-20 Operator's Manual
Cat. No. / No de cat.
2775-20
M18™ FUEL™ SWITCH PACK™ SECTIONAL DRUM SYSTEM
SYSTÈME DE TAMBOUR TRANSVERSAL M18™ FUEL™
SWITCH PACK™
SISTEMA DE TAMBOR MODULAR M18™ FUEL™ SWITCH PACK™
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
2
3
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instructions, illustrations and specifica-
tions provided with this power tool. Failure to follow
all instructions listed below may result in electric shock,
re and/or serious injury. Save all warnings and instructions for future reference. The term "power tool"
in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
WORK AREA SAFETY
• Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
• Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
• Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Un-
modied plugs and matching outlets will reduce risk
of electric shock.
• Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
• Do not abuse the cord. Never use the cord for car-
rying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
• When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric
shock.
• If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of an GFCI reduces
the risk of electric shock.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not
use a power tool while you are tired or under the
inuence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result
in serious personal injury.
• Use personal protective equipment. Always wear
eye protection. Protective equipment such as a dust
mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce
personal injuries.
• Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your nger on the
switch or energizing power tools that have the switch
on invites accidents.
• Remove any adjusting key or wrench before turn-
ing the power tool on. A wrench or a key left attached
to a rotating part of the power tool may result in per-
sonal injury.
• Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
• Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts. Loose clothes, jewelry or long hair can
be caught in moving parts.
• If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust col-
lection can reduce dust-related hazards.
• Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
POWER TOOL USE AND CARE
• Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
• Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting
the power tool accidentally.
• Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained
users.
• Maintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power
tool repaired before use. Many accidents are caused
by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
• Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a hazard-
ous situation.
• Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles
and grasping surfaces do not allow for safe handling
and control of the tool in unexpected situations.
BATTERY TOOL USE AND CARE
• Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of re when used with
another battery pack.
• Use power tools only with specically designated
battery packs. Use of any other battery packs may
create a risk of injury and re.
• When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause
burns or a re.
• Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact ac-
• Place the drain cleaner at a distance no greater
than two feet from drain opening. If the drain
cleaner cannot be placed within two feet from the
drain opening, the drain opening will need to be
extended using a similar size pipe and ttings.
Greater distances can cause control problems leading
to twisting, kinking, breaking or whipping of the cable.
• One person must control both the trigger switch
and cable. If the tool stops rotating, the user must be
able to turn the tool off to prevent twisting, kinking,
breaking or whipping of the cable.
• Do not operate the drain cleaner in reverse rotation
except as described in this manual. Running the tool
in reverse for extended periods can cause damage to
the cable and accessories.
•
WARNING
To reduce the risk of re, personal injury, and product damage due to a
short circuit, never immerse your tool, battery pack or
charger in uid or allow a uid to ow inside them.
Corrosive or conductive uids, such as seawater,
certain industrial chemicals, and bleach or bleach
containing products, etc., can cause a short circuit.
• Maintain labels and nameplates. These carry im-
portant information. If unreadable or missing, contact
a MILWAUKEE service facility for a free replacement.
•
WARNING
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paint
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
lter out microscopic particles.
SPECIFICATIONS
Cat. No. ..........................................................2775-20
Volts ...................................................................18 DC
No Load RPM ........................................................250
Battery Type .....................................................M18™
Charger Type ....................................................M18™
Drum Cat. No............................................ 47-53-2775
Cable Range..............................................5/16" - 5/8"
Pedal Cat. No ........................................... 14-02-0000
SYMBOLOGY
Volts
Direct Current
No-Load Revolutions per Minute (RPM)
C
US
UL Listing Mark for
Canada and U.S.
Do not allow battery to contact corrosive
or conductive uid
Only wear leather gloves
Do not transport this tool when the
drum and backpack are connected
cidentally occurs, ush with water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
• Do not use a battery pack or tool that is damaged or
modied. Damaged or modied batteries may exhibit
unpredictable behavior resulting in re, explosion or
risk of injury.
• Do not expose a battery pack or tool to re or ex-
cessive temperature. Exposure to re or temperature
above 265°F (130°C) may cause explosion.
• Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specied in the instructions. Charging im-
properly or at temperatures outside the specied range
may damage the battery and increase the risk of re.
SERVICE
• Have your power tool serviced by a qualied repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
• Never service damaged battery packs. Service of
battery packs should only be performed by the manu-
facturer or authorized service providers.
SPECIFIC SAFETY RULES
• Only grasp the rotating cable with gloves recom-
mended by the manufacturer. Latex or loose tting
gloves or rags can become wrapped around the cable
and may result in serious personal injury.
• Do not allow the cutter to stop turning while the
cable is turning. This can overstress the cable and
may cause twisting, kinking or breaking of the cable
and may result in serious personal injury.
• Use latex or rubber gloves inside the gloves rec-
ommended by the manufacturer, goggles, face
shields, protective clothing, and respirator when
chemicals, bacteria or other toxic or infectious substances are suspected to be in a drain line. Drains
may contain chemicals, bacteria and other substances
that may cause burns, be toxic or infectious or may
result in other serious personal injury.
• Practice good hygiene. Do not eat or smoke while
handling or operating the tool. After handling or
operating drain cleaning equipment, use hot, soapy
water to wash hands and other body parts exposed
to drain contents. This will help reduce the risk of health
hazards due to exposure to toxic or infectious material.
• Only use the drain cleaner for the recommended
drain sizes. Using the wrong size drain cleaner can
lead to twisting, kinking or breaking of the cable and
may result in personal injury.
• Inspect cable for wear and damage before use.
Replace a worn or damaged cable before using the
drain cleaner.
• Do not twist, kink or over bend cables. Breaking of
the cable may result in serious personal injury.
• Inspect the drain to be cleaned before use. If pos-
sible, determine the access point(s) to the drain, the
size(s) and length(s) of the drain, distance to mainlines,
the nature of the blockage, presence of drain clean-
ing chemicals or other chemicals, etc. If chemicals
are present in the drain, it is important to understand
the specic safety measures required to work around
those chemicals. Contact the chemical manufacturer
for required information.
• If needed, place protective covers in the work area.
The drain cleaning process can be messy.
• Make sure cable is fully retracted inside of the drain
cleaner. This will prevent whipping at start up.
4
5
ASSEMBLY
WARNING
Recharge only with the charger
specied for the battery. For specic charging instructions, read the operator’s
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons and
pull the battery pack away from the tool.
WARNING
Always remove battery pack before
changing or removing accessories.
To insert the battery, slide the pack into the body of the
tool. Make sure it latches securely into place.
WARNING
Only use accessories specically
recommended for this tool. Others
may be hazardous.
Always store tool in its bucket with insert to avoid
damage to the cable.
Selecting the Proper Cable
Cat. No. Description
Pipe
Diameter
48-53-2772
5/16" x 75' Inner Core Drop Head Cable
w/ Rustguard
1-1/4" - 2-1/2"
48-53-2773
3/8" x 50' Inner Core Coupling Cable
w/ Rustguard
2" - 3"
48-53-2774
1/2" x 50' Inner Core Coupling Cable
w/ Rustguard
2" - 4"
48-53-2775
5/8" x 50' Open Wind Coupling Cable
w/ Rustguard
1-1/4" - 3"
Cable Attachments for Use with
Milwaukee Coupling Cables
Cat. No. Description
Pipe
Diameter
48-53-2681 Small Bulb Head w/ Rustguard 2" - 3"
48-53-2682 Small Drop Head w/ Rustguard 2" - 3"
48-53-2683 1" Spade Bit w/ Rustguard 2" - 3"
48-53-2684 1" C-Cutter w/ Rustguard 2" - 3"
48-53-2685
5 Piece Small Drain Line Kit
w/ Rustguard
2" - 3"
48-53-2786 Medium Bulb Head w/ Rustguard 2" - 4"
48-53-2787 Medium Drop Head w/ Rustguard 2" - 4"
48-53-2788 1-1/2" Spade Bit w/ Rustguard 2" - 4"
48-53-2789 1-1/2" C-Cutter w/ Rustguard 2" - 4"
48-53-2790
5 Piece Medium Drain Line Kit
w/ Rustguard
2" - 4"
CAUTION
To prevent damage to the cable and
attachments, do not use in larger diameter
pipes.
Cable Installation
WARNING
To reduce the risk of injury, wear
safety goggles or glasses with side
shields. Always wear leather gloves. Cable tip may
be sharp.
Remove the cable for cleaning after each use. Different size and types of cables are available for different
applications.
FUNCTIONAL DESCRIPTION
1
2
1. Handle
2. Inner drum
3. Cable
4. Latches
5. Head attachment
storage
6. Drum alignment
guides
7. Foot pedal
storage
8. Drive belt
9. Forward/
Off/Reverse
switch
10. Foot pedal
11. Cord wrap
3
Drum
4
5
6
7
8
9
4
10
11
Powered Base
Inner
Powered Base
Outer
12
13
14
15
12. Backpack snaps
13. Chest buckle straps
14. Kickstand
15. Battery bay
To remove the cable:
1. Turn the forward/off/reverse switch to the off position
O and remove the battery pack.
2. Pull the cable out through the nose of the drum until
the anchor cable shows.
3. Remove the cable from the anchor cable by insert-
ing the pin key into the coupling hole and pulling the
cable away.
4. To clean or maintain cable, follow the cleaning instructions under "Maintenance".
To install the cable:
1. Turn the forward/off/reverse switch to the off position
O and remove the battery pack.
2. Install the cable to the anchor cable by snapping the
attachment coupler into the cable coupler.
3. Feed the cable into the drum.
4. Remove the protective tip cover from new cables
before use.
Cable Attachment Installation
To install the attachment:
Snap the attachment coupler into the cable coupler.
Test the cable before inserting into the drain to make
sure the attachment does not fall off during use.
To remove the attachment:
Insert the pin key into the coupling hole and pull attach-
ment off of cable.
Transportation and Set Up
WARNING
Do not transport this tool when the
drum and backpack are connected.
Tipping may occur.
To transport the tool:
1. Remove drum from the backpack area.
2. Place the foot pedal in its storage and
tie the pedal cord using the cord wrap.
3. Place the backpack over back and
buckle the chest straps together.
4. Lift the drum to the drain area, as
shown.
To set up the tool:
1. Once at the drain, area, remove
backpack and place it no further
than 2' from the drain. WARNING!
Greater distance can cause twisting,
kinking, breaking or whipping of the
cable.
2. Remove the foot pedal and cord from
the backpack and place to the side, ensuring the cord
will not tangle with the tool cable.
3. Place the drum onto the powered base by using
the drum alignment guides. Press drum down onto
powered base while latching to ensure a complete
connection.
OPERATION
WARNING
Always remove battery pack before
changing or removing accessories.
Only use accessories specically recommended
for this tool. Others may be hazardous.
To reduce the risk of short circuit, when setting tool
or battery down, do not allow battery to contact
corrosive or conductive uid.
To reduce the risk of injury, wear safety goggles
or glasses with side shields. Always wear leather
gloves.
Using Forward/Off/Reverse Switch
1. For forward (clockwise) rotation, turn the forward/
off/reverse switch to the arrow pointing towards the
nose of the drum . Check the direction of rotation
before use.
2. For reverse (counterclockwise) rotation, turn the
forward/off/reverse switch to the arrow pointing away
from the nose of the drum . Check the direction of
rotation before use.
3. To lock the switch, turn the forward/off/reverse switch
to the center position O. The foot pedal will not work
while the forward/off/reverse switch is in the center
locked position. Always lock the switch or remove
the battery pack before performing maintenance,
changing accessories, storing the tool and any time
the tool is not in use.
Starting and Stopping Speed
1. To start the tool, push the forward/off/reverse switch
to either direction and step or kneel on the foot pedal.
2. To stop the tool, release pressure on the pedal.
Inserting Cable Into Drain
1. Transport and set the tool up according to the instructions under "Transportation and Set Up".
2. Grasp the cable close to the tool and feed at least 2'
into the drain. WARNING! Wear leather gloves.
3. Turn the forward/off/reverse switch to the forward
position and engage the foot pedal to begin rotating
the cable.
4. Continue feeding cable
into the drain until the
obstruction is reached.
NOTE: If more cable is
needed to reach the clog, a
second drum may be con-
nected. To do this, turn the
forward/off/reverse switch to
the off position O. Remove
the drum from the powered
base and place to the side.
Insert a new drum onto the
powered base. Disconnect
the anchor cable from the
original drum and and connect it to the anchor cable in the second cable according
to instructions under "Cable Attachment Installation".
5. When the clog is reached, move the cable in a back
and forth motion until the obstruction is cleared. If
the tool binds, release pressure from the foot pedal
immediately. Repeat until the drain is clear.
6
7
To Unbind Cable
1. Turn the forward/off/reverse switch to the reverse
position and engage the foot pedal to begin rotat-
ing the cable.
2. Withdraw the tool a few inches while in reverse to
free the cable.
3. Stop the tool.
4. After the tool has come to a complete stop, switch
back to the forward position.
CAUTION
Running the tool in reverse for
extended periods can cause damage
to the cable and accessories.
Removing Cable From Drain
1. Turn the forward/off/reverse switch to the forward
position and engage the foot pedal.
2. Pull the cable away from the drain.
3. Wipe the exposed cable with a rag and feed it back
into the drum.
4. Repeat steps 2-4 until the cable is free from the drain.
5. Before storing the tool, wash the cable and drum (see
"Cleaning Cables and Drums" in Maintenance).
MAINTENANCE
WARNING
To reduce the risk of injury, always
unplug the charger and remove the
battery pack from the charger or tool before performing any maintenance. Never disassemble the
tool, battery pack or charger. Contact a MILWAUKEE
service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good repair
by adopting a regular maintenance program. Inspect
your tool for issues such as undue noise, misalignment
or binding of moving parts, breakage of parts, or any
other condition that may affect the tool operation. Return
the tool, battery pack, and charger to a MILWAUKEE
service facility for repair. After six months to one year,
depending on use, return the tool, battery pack and
charger to a MILWAUKEE service facility for inspection.
If the tool does not start or operate at full power with a
fully charged battery pack, clean the contacts on the bat-
tery pack. If the tool still does not work properly, return
the tool, charger and battery pack, to a MILWAUKEE
service facility for repairs.
WARNING
To reduce the risk of re, personal
injury, and product damage, never
immerse your tool, battery pack or charger in uid
or allow a uid to ow inside them.
Cleaning
Clean dust and debris from vents. Keep handles clean,
dry and free of oil or grease. Use only mild soap and a
damp cloth to clean, since certain cleaning agents and
solvents are harmful to plastics and other insulated
parts. Some of these include gasoline, turpentine,
lacquer thinner, paint thinner, chlorinated cleaning solvents, ammonia and household detergents containing
ammonia. Never use ammable or combustible solvents
around tools.
Cleaning Cables and Drums
The cable and drum should be thoroughly ushed with
water after every use to prevent damaging effects of
sediment and drain cleaning compounds. WARNING!
Wear leather gloves. After washing, dry the cable and
drum completely. Then, wipe cable with an oiled rag
before returning it to the drum according to the instruc-
tions in "Cable Installation".
Repairs
For repairs, return the tool, battery pack and charger to
the nearest service center.
ACCESSORIES
WARNING
Use only recommended accessories.
Others may be hazardous.
For a complete listing of accessories, go online to www.
milwaukeetool.com or contact a distributor.
SERVICE - UNITED STATES
1-800-SAWDUST (1.800.729.3878)
Monday-Friday, 7:00 AM - 6:30 PM CST
or visit www.milwaukeetool.com
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: metproductsupport@milwaukeetool.com
Become a Heavy Duty Club Member at
www.milwaukeetool.com to receive important
notications regarding your tool purchases.
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
LIMITED WARRANTY
USA & CANADA
Every MILWAUKEE power tool* (see exceptions below) is warranted
to the original purchaser only to be free from defects in material and
workmanship. Subject to certain exceptions, MILWAUKEE will repair
or replace any part on an electric power tool which, after examination,
is determined by MILWAUKEE to be defective in material or workman-
ship for a period of ve (5) years** after the date of purchase unless
otherwise noted. Return of the power tool to a MILWAUKEE factory
Service Center location or MILWAUKEE Authorized Service Station,
freight prepaid and insured, is required. A copy of the proof of purchase
should be included with the return product. This warranty does not
apply to damage that MILWAUKEE determines to be from repairs
made or attempted by anyone other than MILWAUKEE authorized
personnel, misuse, alterations, abuse, normal wear and tear, lack of
maintenance, or accidents.
Normal Wear: Many power tools need periodic parts replacement and
service to achieve best performance. This warranty does not cover
repair when normal use has exhausted the life of a part including,
but not limited to, chucks, brushes, cords, saw shoes, blade clamps,
o-rings, seals, bumpers, driver blades, pistons, strikers, lifters, and
bumper cover washers.
*This warranty does not cover Air Nailers & Staplers; Airless Paint
Sprayer; Cordless Battery Packs; Gasoline Driven Portable Power
Generators; Hand Tools; Hoist – Electric, Lever & Hand Chain; M12™
Heated Gear; Reconditioned Product; and Test & Measurement
Products. There are separate and distinct warranties available for
these products.
**The warranty period for Job Site Radios, M12™ Power Port, M18™
Power Source, Jobsite Fan and Trade Titan™ Industrial Work Carts is
one (1) year from the date of purchase. The warranty period for the
Drain Cleaning Cables is two (2) years from the date of purchase. The
warranty period for the M18™ Compact Heat Gun and the 8 Gallon
Dust Extractor is three (3) years from the date of purchase. The war-
ranty period for the LED in the LED Work Light and the LED Upgrade
Bulb for the Work Light is the lifetime of the product subject to the
limitations above. If during normal use the LED or LED Bulb fails, the
part will be replaced free of charge.
Warranty Registration is not necessary to obtain the applicable war-
ranty on a MILWAUKEE power tool product. The manufacturing date
of the product will be used to determine the warranty period if no proof
of purchase is provided at the time warranty service is requested.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT
REMEDIES DESCRIBED HEREIN IS A CONDITION OF THE CONTRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT.
IF YOU DO NOT AGREE TO THIS CONDITION, YOU SHOULD NOT
PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE
BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL
OR PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES,
EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY
PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR
LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU
OF ALL OTHER EXPRESS WARRANTIES, WRITTEN OR ORAL.
TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH
DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WARRANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE
EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES
DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO
YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,
AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
Please consult the ‘Service Center Search’ in the Parts & Service sec-
tion of MILWAUKEE’s website www.milwaukeetool.com or call 1.800.
SAWDUST (1.800.729.3878) to locate your nearest service facility for
warranty and non-warranty service on a Milwaukee electric power tool.
LIMITED WARRANTY - MEXICO,
CENTRAL AMERICA & CARIBBEAN
TECHTRONIC INDUSTRIES' warranty is for 5 years since the original
purchase date.
This warranty card covers any defect in material and workmanship
on this Product.
To make this warranty valid, present this warranty card, sealed/
stamped by the distributor or store where you purchased the product,
to the Authorized Service Center (ASC). Or, if this card has not been
sealed/stamped, present the original proof of purchase to the ASC.
Call toll-free1 01 (800) 030-7777 to nd the nearest ASC, for service,
parts, accessories or components.
Procedure to make this warranty valid
Take the product to the ASC, along with the warranty card sealed/
stamped by the distributor or store where you purchased the product,
and any faulty piece or component will be replaced without cost for
you. We will cover all freight costs relative with this warranty process.
Exceptions
This warranty is not valid in the following situations
a) When the product is used in a different manner from the end-user
guide or instruction manual.
b) When the conditions of use are not normal.
c) When the product was modied or repaired by people not authorized
by TECHTRONIC INDUSTRIES.
Note: If cord set is damaged, it should be replaced by an Authorized
Service Center to avoid electric risks.
SERVICE AND ATTENTION CENTER
Call to 01 (800) 030-7777
IMPORTED AND COMMERCIALIZED BY
TECHTRONIC INDUSTRIES MEXICO, SA DE CV
Av President Masarik #29 piso 7, Col. Polanco V Sección
CP 11560, Deleg. Miguel Hidalgo, CDMX
Model:
Date of Purchase:
Distributor or Store Stamp:
RÈGLES DE SÉCURITÉ GÉNÉRALES
RELATIVES AUX OUTILS ÉLECTRIQUES
AVERTISSEMENT
Lire toutes les consignes
de sécurité, consignes, illustrations et spécifications fournies avec cet
outil électrique. Ne pas suivre l’ensemble des règles
et instructions peut entraîner une électrocution, un in-
cendie ou des blessures graves. Conserver les règles
et les instructions à des ns de référence ultérieure.
Le terme «outil électrique» gurant dans les avertissements ci-dessous renvoie à l’outil électrique à alimenta-
tion par le réseau (à cordon) ou par batterie (sans l).
SÉCURITÉ DU LIEU DE TRAVAIL
• Veillez à ce que l’aire de travail soit propre et
bien éclairée. Le désordre et le manque de lumière
favorisent les accidents.
• Ne pas utiliser d’outils électriques dans des at-
mosphères explosives, par exemple en présence
de liquides, gaz ou poussières inflammables.
Les outils électriques produisent des étincelles
risquant d'enflammer les poussières ou vapeurs.
• S’assurer que les enfants et les curieux se trouvent
à une bonne distance au moment d’utiliser un outil
électrique. Les distractions peuvent causer une perte
de contrôle.
SÉCURITÉ ÉLECTRIQUE
• Les fiches des outils électriques doivent cor-
respondre à la prise secteur utilisée. Ne jamais
modier la che, de quelque façon que ce soit.
Ne jamais utiliser d'adaptateurs de che avec des
outils mis à la terre. Les ches et prises non modiées
réduisent le risque de choc électrique.
• Éviter tout contact avec des surfaces mises à
la terre comme des tuyaux, des radiateurs, des
cuisinières et des réfrigérateurs. Le risque de choc
électrique est accru lorsque le corps est mis à la terre.
• Ne pas exposer les outils électriques à l'eau ou
l'humidité. La pénétration d’eau dans ces outils accroît
le risque de choc électrique.
• Ne pas maltraiter le cordon d'alimentation. Ne
jamais utiliser le cordon d’alimentation pour trans-
porter l’outil électrique et ne jamais débrancher ce
dernier en tirant sur le cordon. Garder le cordon à
l'écart de la chaleur, de l'huile, des objets tranchants
et des pièces en mouvement. Un cordon endom-
magé ou emmêlé accroît le risque de choc électrique.
• Pour les travaux à l’extérieur, utiliser un cordon
spécialement conçu à cet effet. Utiliser un cordon
conçu pour l'usage extérieur réduit les risques de choc
électrique.
• Si l’utilisation d’un outil électrique est inévita-
ble dans un endroit humide, utiliser une source
d’alimentation munie d’un disjoncteur de fuite de
terre. L’utilisation d’un disjoncteur de fuite de terre ré-
duit le risque de choc électrique. sécurité individuelle.
SÉCURITÉ INDIVIDUELLE
• Rester attentif, prêter attention au travail et faire
preuve de bon sens lors de l'utilisation de tout outil
électrique. Ne pas utiliser cet appareil en cas de
fatigue ou sous l’inuence de l’alcool, de drogues
ou de médicaments. Un moment d’inattention pen-
dant l’utilisation d’un outil électrique peut entraîner des
blessures graves.
• Porter l’équipement de protection individuel req-
uis. Toujours porter une protection oculaire. Selon
les conditions, porter aussi un masque antipoussières,
des bottes de sécurité antidérapantes, un casque
Loading...