Milwaukee 2684-20 Service Parts List

EXAMPLE:

00

Component Parts (Small #)

0

Are Included When Ordering
The Assembly (Large #).

SERVICE PARTS LIST

SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS

M18 FUEL™ 15mm Random Orbital Polisher

CATALOG NO. 2684-20

STARTING
SERIAL NO.

M08A

BULLETIN NO.

54-32-0010

REVISED BULLETIN

WIRING INSTRUCTION

SEE REVERSE SIDE

DATE

Oct. 2021

44

40
x4

48

40 43
44

40
x6

43

39

42

41

36

1

47

11 12
13

11

37

38

10
x4

49

4

36 39
40 45

x2

5

6

52

46

16

45

50

12

FIG. PART NO. DESCRIPTION OF PART NO. REQ.

1 14-20-0347 Electronics Assembly 1

 4 42-14-0028 Ba󰀪e 1

5 06-82-2380 #8-32 Pan Hd. T-20 Screw 6
6 44-66-0209 Retaining Plate 1
10 05-88-1300 M4 x 1.4 x 28mm Pan Hd. T-20 Screw 4
11 --------------- Shroud Support 1
12 --------------- Shroud Cover 1
13 06-82-0135 M3 x 1.34 T-10 Screw 6
16 34-40-0206 O-Ring 1
22 05-90-0225 Spring Washer 4
33 05-81-1160 M3 x 6mm Washer Screw 3
34 49-36-0401 5" Backing Plate (Recommended) 1
49-36-0402 6" Backing Plate (Optional Accessory) 1
35 06-82-0251 M4 x 8mm Recess Hex Screw 4
36 --------------- Housing Support (Left Housing) 1
37 42-42-0077 Lock On Button 1
38 40-50-0277 Lock On Spring 1
39 --------------- Housing Cover (Right Housing) 1
40 06-82-1076
41 31-15-0114 Mesh Filter Assembly 1
42 45-72-0031 Trigger 1
43 --------------- Battery Housing Cover 1
44 --------------- Battery Housing Support 1
45 12-20-0370 Service Nameplate 1
46 14-30-0126 Gearbox Assembly 1
47 31-44-0292 Pommel Assembly 1
48 31-44-0291 Battery Housing Assembly 1
49 31-44-0290 Housing Assembly 1
50 14-73-0233 Output Assembly 1
51 14-73-0234 Receiver Assembly 1
52 16-01-0054 Rotor Assembly 1

M4 x 1.4 x 16mm Pan Hd. ST T-20 Screw

10

13
x6

MILWAUKEE TOOL

22
x4

5

x4

51

33
x3

34

35
x4

l

13135W.LisbonRoad,Brookeld,WI53005

www.milwaukeetool.com

Drwg. 3

Carefully place/route ribbon cable in traps
as shown.

Route all wires and wire groupings through
wire traps as shown. Be sure to push wires,
sleeved wire groupings and ribbon cables
firmly below wire trap openings.

Avoid bending wires sharply from switch.

Be careful and do not tighten or strain the
wires in this area.

• As an aid to reassembly, take notice of wire routing and position in wire guides and traps while dismantling tool.

• Be sure that all components of the electronics kit are seated rmly and squarely in the handle recesses.

• Avoid pinched wires, be sure that all wires and sleeves are pressed

completely down in wire guides and traps.

• Prior to installing the handle cover onto
the handle support, be sure that there
are no interferences.

SEAT TORQUE
FIG. PART NO. WHERE USED (KG/CM) (IN/LBS)
5 06-82-2380 Gear Case 22±2.0 19±2.0
10 05-88-1300 Gear Case 20±2.0 17±2.0
13 06-82-0135 Shroud Cover 10.0±1.0 8.5±1.0
24 --------------- Lower Counterweight 15±1.5 13±1.5
28 --------------- Upper Counterweight 20±2.0 17±2.0
33 05-81-1160 Reciever Plate 10±1.0 8.5±1.0
35 06-82-0251 Backing Plate 25±2.5 21.5±2.5
40 06-82-1076 Foot Support 14±1.5 12±1.5

SCREW TORQUE SPECIFICATIONS

When servicing, remove 90-95% of the exist­ing grease prior to installing Type 'Y'. Original
grease may be similar in color but not
compatible with 'Y'.

LUBRICATION NOTES:

Use Type ‘Y’ Grease, No. 49-06-5270 (6 ounce tube)
No. 49-06-5275 (14 ounce tub)

Place 20±2.0 grams of grease in the Gear Case
cavity, around the Pinion and above and below the
Bevel Gear.

Place a heavy coating of grease to the teeth of the
Bevel Gear and to the teeth of the Pinion Gear
on the Rotor Assembly #52.