SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
CATALOG NO.
EXAMPLE:
00
Component Parts (Small #)
0
Are Included When Ordering
The Assembly (Large #).
SERVICE PARTS LIST
M12™ Right Angle 1/4" Hex Impact Driver
58
2467-20
50b
STARTING
SERIAL NO.
G53A
43
BULLETIN NO.
54-26-2060
REVISED BULLETIN
WIRING INSTRUCTION
See Page 2
50d
DATE
July 2015
57
52a
52
38
49
52b
52a 52b
52c
51a 51b
51
51c 51d
50a
51c
51a
51b
50c
(4x)
41
(5x)
56
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 42-38-0500 Rubber Bumper Ring 1
2 44-90-0650 Retaining Ring 1
3 45-88-0428 Washer 1
4 40-50-0297 Spring 1
5 45-22-0880 Sleeve 1
9 02-02-7045 2.5mm Steel Ball 2
38 40-50-0027 Spring Plate 1
39 42-42-0084 Forward / Reverse Shuttle 1
40 31-92-0316 Trigger 1
41 06-82-1080 M13 x 14mm Pan Hd. Plast. T-10 Screw 5
43 44-06-0180 Fuel Gauge Lens 1
49 43-44-7062 Motor Brush Seal 1
50 31-44-2467 Housing Assembly 1
50a --------------- Housing Cover, Housing Halve-Right 1
50b --------------- Housing Support, Housing Halve-Left 1
50c 45-30-2653 Rubber Slug 4
50d --------------- Fuel Gauge Label 1
51 23-66-2467 Electronics Assembly 1
51a --------------- Battery Connector Block 1
51b --------------- On-Off Switch 1
51c --------------- PCBA 1
51d --------------- LED Assembly 1
52 23-30-1041 Motor Assembly with Pinion 1
52a --------------- Motor 1
52b --------------- Motor Mount Plate 1
52c --------------- Motor Mount Screw 2
53 42-06-1038 Anvil Assembly 1
53a --------------- Anvil 1
53c --------------- Nylon Washer 1
54 28-14-2467 1/4" Hex Gearcase Assembly 1
55 43-81-0201 Hammer Assembly 1
56 12-20-2469 Service Nameplate 1
57 42-55-2415 Contractor Bag 1
58 42-70-0058 Housing Connection Clip 1
52c
(2x)
39
40
51d
55
53a
53a
53
53c
2 3 4
54
5 9
5
4
3
2
1
MILWAUKEE TOOL www.milwaukeetool.com
13135 W. LISBON RD., BROOKFIELD, WI 53005
50
50a 50b
50c 50d
53c
9
(2x)
Drwg. 1
PCBA (51c)
NOTE:
As an aid to reassembly, be sure
that the left arm of Motor Mount
Plate (52b) and the left lug of
Hammer Assembly (55) are
firmly and squarely seated
in the corresponding cavities of the Left Handle
Halve (50b).
Motor Assembly (52) is to be positioned
with the Red Dot (positive terminal)
to the top
Hammer
Assy. (55)
Lug
Motor
Mount
Plate (52b)
Arm
Battery
Connector
On-Off
Switch (51b)
Block (51a)
Spring Plate (38)
Forward/Reverse
Shuttle (39)
AS AN AID TO REASSEMBLY, TAKE NOTICE OF WIRE ROUTING AND
POSITION IN WIRE GUIDES AND TRAPS WHILE DISMANTLING TOOL.
BE SURE THAT ALL COMPONENTS OF THE ELECTRONICS KIT
ARE SEATED FIRMLY AND SQUARELY IN THE HANDLE RECESSES.
AVOID PINCHED WIRES, BE SURE THAT ALL WIRES AND SLEEVES
ARE PRESSED COMPLETELY DOWN IN WIRE GUIDES AND TRAPS.
PRIOR TO INSTALLING THE HANDLE COVER ONTO THE HANDLE
SUPPORT, BE SURE THAT THERE ARE NO INTERFERENCES.
Trigger (40)
LED
Assembly (51d)
= WIRE TRAPS
or GUIDES
Loading...