EXAMPLE:
00
Component Parts (Small #) Are Included
0
When Ordering The Assembly (Large #).
28
29
34
32
(4)
33
SERVICE PARTS LIST
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
M18™ FUEL™ Spot Clean Up Vacuum
CATALOG NO.
27 32
81
33
0940-20
63
27
26
(2x)
25
23
STARTING
SERIAL NO.
48
21
(4x)
L51A
13
19
61
BULLETIN NO.
54-05-0285
REVISED BULLETIN
WIRING INSTRUCTION
See page two
1 11
80
53 78
53
DATE
Sept. 2020
59
78
1
4
6
9
4
82
6
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 31-50-0088 Main Housing Halve-Right (1)
4 43-31-0011 Filter Assembly (1)
6 43-31-0013 Foam Filter (1)
9 31-15-0111 Main Housing Cover Assembly-Right (1)
11 06-82-0212 M4 x 16mm Pan Hd. ST Screw (13)
13 23-26-0035 Light Guide (1)
14 42-42-0076 Two Speed On-O Push Button (1)
19 23-66-0301 Switch PCBA (1)
21 06-82-0213 M3 x 12mm Pan Hd. ST Screw (4)
22 34-40-0247 O-Ring (1)
23 31-15-0125 Motor Housing Front Cover (1)
25 44-66-0153 Motor Seal Cover Plate (1)
26 42-76-0071 Motor Sleeve (2)
27 23-14-0030 Motor Insulator-Left (1)
28 44-52-0086 Motor Housing Shock Pad (1)
29 43-31-0021 Soundproof Foam Filter (1)
32 06-82-0246 M3 x 12mm Pan Hd ST Screw (4)
33 23-14-0032 Motor Insulator-Right (1)
34 14-20-0186 Electronics Assembly (1)
37 42-92-0088 Cyclone Inner Hood (1)
42 23-33-0016 Socket Assembly (1)
44 44-14-0076 Inlet Connector Assembly (1)
45 42-28-0036 Button Fixing Block (1)
47 06-82-0236 M3 x 12mm Pan Hd. ST Screw (6)
48 43-81-0077 Impeller (1)
51 31-44-0318 Cyclone Housing Assembly (1)
53 31-44-0256 Main Housing Halve-Left (1)
59 31-15-0211 Main Housing Cover Assembly-Left (1)
61 43-84-0024 'FUEL' Brushless Plate (1)
63 42-51-0022 Debris Tank Assembly (1)
70 45-86-0068 Wand (1)
71 31-01-0101 Power Floor Tool (1)
72 31-01-0102 Non-Powered Floor Tool (1)
73 14-37-0109 Hose (1)
74 31-01-0103 Accessory Holder (1)
75 31-01-0104 Utility Tool (1)
76 49-90-2017 Round Brush Tool (1)
77 31-01-0865 Crevice Tool (1)
78 12-20-0283 Service Nameplate (1)
79 31-01-0106 Beater Bar (1)
80 31-44-0289 Main Housing Service Kit (1)
81 23-16-0177 Motor Insulator Kit (1)
82 49-90-2012 Replacement Filter Assembly (1)
22
47
(4x)
11
(13x)
44
75
74
71
79
79
42
47
(2x)
45
14
51
37
76
70
72
MILWAUKEE TOOL l www.milwaukeetool.com
MILWAUKEE ELECTRIC TOOL CORPORATION
13135 W. Lisbon Road, Brookeld, Wisc. 53005
13135 W. LISBON RD., BROOKFIELD, WI 53005
73
77
Drwg. 1
Drwg. 1
• As an aid to reassembly, take notice of wire routings and position in wire guides and traps
while dismantling tool.
• Route wires into wire traps and channels as shown.
• Be sure to place wires down into wire traps, being sure to remove any wire slack while routing.
• Be sure all components of electronics assembly are seated firmly and squarely in the corresponding cavity of handle support.
• Be sure there are no interferences when installing handle cover over handle support. Watch for pinched wires.
• Check for proper functionality of slide buttons and switch prior to installing battery.
Loading...