Milnor 42031, 42044 CP2, 42044 CP3 Service Manual

Published Manual Number/ECN: MPP42SUPAE/2000036N

• Publishing System: TPAS

• Access date: 01/19/2000

• Document ECN's: Latest Available

Service— 42031, 42044 CP2/CP3

Washer-Extractors

PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.

Please Read

About the Manual Identifying Information on the Cover

The front cover displays pertinent identifying information for this manual. Most important, are the published manual number (part number) /ECN (date code). Generally, when a replacement manual is furnished, it will have the same published manual number, but the latest available ECN. This provides the user with the latest information applicable to his machine. Similarly all documents comprising the manual will be the latest available as of the date the manual was printed, even though older ECN dates for those documents may be listed in the table of contents.

When communicating with the Milnor factory regarding this manual, please also provide the other identifying information shown on the cover, including the publishing system, access date, and whether the document ECN’s are the latest available or exact.

References to Yellow Troubleshooting Pages

This manual may contain references to “yellow pages.” Although the pages containing troubleshooting procedures are no longer printed on yellow paper, troubleshooting instructions, if any, will be contained in the easily located “Troubleshooting” chapter or section. See the table of contents.

Trademarks of Pellerin Milnor Corporation

The following, some of which may be used in this manual, are trademarks of Pellerin Milnor Corporation:

Ampsaver Autolint Auto-Purge

Autovac E-P Plus

CBW Dye-Extractor® Hands-Off Dyextractor® Hydro-Cushion

Gear Guardian

Mildata

Milnet Milnor

Staph-Guard

System 4 Miltrac System 7 Miltron Totaltrol

Comments and Suggestions

Help us to improve this manual by sending your comments to:

Pellerin Milnor Corporation Attn: Technical Publications P. O. Box 400 Kenner, LA 70063-0400

Fax: (504) 469-1849

Table of Contents

for MPP42SUPAE/2000036N

42031, 42044 CP2/CP3 Washer-Extractors

Page Description Document/ECN

1 Approval and Procurement Record BMP74009/81213 3 Warranty BMP720097/92732A 4 How to Order Parts BMP720097R/72332A

5 Section 1: Lubrication

6 Lubrication Chart BMP701483/71172A 7 Lubrication Instructions BMP701450/73047A

9 Section 2: Drive Components

10 Clutch, Brake and Drive BMP700246/70023A

11 Section 3: Main Bearings and Seals

12 Removal, Installation & Setting Main Bearings & Seals BMP701227/78337A 13 Removal, Installation & Setting Main Bearings & Seals BMP701227R/78337A 14 Removal, Installation & Setting Main Bearings & Seals BMP701228/78337A 15 Removal, Installation & Setting Main Bearings & Seals BMP701228R/78337A

17 Section 4: Steam and Air

18 Servicing Air Cylinders MSSM0130AE/9313AV 19 Burket Steam Valve BMP800020/96066V

21 Section 5: Installation

22 Installation BMP720107/72352A 23 Installation BMP720107R/77412A 24 Installation BMP720108/72352A 25 Installation BMP720108R/72352A 26 Air Mount Installation - Shipboard 42" BMP770129/87316C 27 Parts List - Air Mount Installation, Shipboard 42" BMP770129R/88432A 28 How to Adjust Water Level BMP701110/71172B

29 Section 6: Fuse and Wire Sizes

30 Recommended Fuse and Wire Sizes BMP700564/83141A 31 Recommended Fuse and Wire Sizes BMP700564R/83141A

33 Section 7: Dimensional Drawings

35 Dimensional Drawing - 42044NP2/CP2 Washer Extractor BD4244NPAE/97112D 36 Dimensional Drawing - 42044NP2/CP2 Options BD4244NPAB/93292D 37 Dimensional Drawing - 42032NP2/CP2 Washer-Extractor BD4231NPAE/97112D 38 Dimensional Drawing - 42031NP2/CP2 Options BD4231NPAB/93292D

3(//(5,10,/125&25325$7,21

/,0,7('67$1'$5':$55$17<

We warrant to the original purchaser that MILNOR machines including electronic hardware/software (hereafter referred to as “equipment”), will be free from defects in material and workmanship for a period of one year from the date of shipment from our factory with no operating hour limitation. This warranty is contingent upon the equipment being installed, operated and serviced as specified in the operating manual supplied with the equipment, and operated under normal conditions by competent operators.

Providing we receive written notification of a warranted defect within 30 days of its discovery, we will – at our option – repair or replace the defective part or parts, FOB our factory. We retain the right to require inspection of the parts claimed defective in our factory prior to repairing or replacing same. We will not be responsible, or in any way liable, for unauthorized repairs or service to our equipment, and this warranty shall be void if the equipment is repaired or altered in any way without MILNOR’s written consent.

Parts which require routine replacement due to normal wear – such as gaskets, contact points, brake and clutch linings and similar parts – are not covered by this warranty, nor are parts damaged by exposure to weather or to chemicals.

We reserve the right to make changes in the design and/or construction of our equipment (including purchased components) without obligation to change any equipment previously supplied.

ANY SALE OR FURNISHING OF ANY EQUIPMENT BY MILNOR IS MADE ONLY UPON THE EXPRESS UNDERSTANDING THAT MILNOR MAKES NO EXPRESSED OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR USE OR PURPOSE. MILNOR WILL NOT BE RESPONSIBLE FOR ANY COSTS OR DAMAGES ACTUALLY INCURRED OR REQUIRED AS A RESULT OF: THE FAILURE OF ANY OTHER PERSON OR ENTITY TO PERFORM ITS RESPONSIBILITIES, FIRE OR OTHER HAZARD, ACCIDENT, IMPROPER STORAGE, MISUSE, NEGLECT, POWER OR ENVIRONMENTAL CONTROL MALFUNCTIONS, DAMAGE FROM LIQUIDS, OR ANY OTHER CAUSE BEYOND THE NORMAL RANGE OF USE. REGARDLESS OF HOW CAUSED, IN NO EVENT SHALL MILNOR BE LIABLE FOR SPECIAL, INDIRECT, PUNITIVE, LIQUIDATED, OR CONSEQUENTIAL COSTS OR DAMAGES, OR ANY COSTS OR DAMAGES WHATSOEVER WHICH EXCEED THE PRICE PAID TO MILNOR FOR THE EQUIPMENT IT SELLS OR FURNISHES.

WE NEITHER ASSUME, NOR AUTHORIZE ANY EMPLOYEE OR OTHER PERSON TO ASSUME FOR US, ANY OTHER RESPONSIBILITY AND/OR LIABILITY IN CONNECTION WITH THE SALE OR FURNISHING OF OUR EQUIPMENT TO ANY BUYER.

BMP720097

92732A

How to order repair parts

Repair parts may be ordered either from the authorized dealer who sold you this machine, or directly from the MILNOR factory. In most cases, your dealer will have these parts in stock.

When ordering parts, please be sure to give us the following in formation:

1. Model and serial number of the machine for which the parts are required

2. Part number

3. Name of the part

4. Quantity needed

5. Method of shipment des ired

6. In correspondence regarding motors or electrical controls, please include all nameplate data, including wiring diagram number and the make or manufacturer of the motor or controls.

All parts will be shipped C.O.D. transportation charges collect on ly.

Please read this manual

It is strongly recommended that you read the installation and operating manual before attempting to install or operate your machine. We suggest that this manual be kept in your business office so that it will not become lo st.

PELLERIN MILNOR CORPORATION

32%2;.(11(5/$  86$

FAX: Administration 504/468-9307, Engineering 504/469-1849, Service 504/469-9777

BMP720097R

72332A