Milnor 42032MXS User Manual

Extract even the most delicate and difficult-to-handle fabrics –
automatically in a CBW® batch washing system

Milnor’s centrifugal extractor – teamed with a CBW® batch washer – brings full automation to processing all
types of linen, even the most delicate and difficult-to-handle fabrics. This broadens the opportunities to use
continuous batch washers, with their inherent savings.

The extractor can be paired with any size Milnor tunnel washer. With cycle times as low as 2 ¼ minutes, depending
upon goods and programming, Milnor’s centrifugal extractor can produce over 25 loads per hour (poly-cotton).
Single motor inverter produces a full range of speeds.

Automatic loading and unloading.

The hydraulic system of Milnor’s centrifugal extractor is
designed to tilt quickly for fast turnaround between loads.

Extracts polycottons and barrier
cloth with ease.

Milnor’s centrifugal extractor works especially well
with polycotton goods, such as uniforms. Low moisture
retention – without setting wrinkles – allows these
uniforms to go directly to a steam finishing tunnel. The
result is faster, higher output plus a superior finish. The
machine’s ability to remove water gently and efficiently
also allows extraction of multifilament or membrane­type barrier cloth for operating rooms – as well as 100%
polyester napery. Maximum moisture removal reduces
drying times and saves fuel.

A variety of configurations.

This versatile centrifugal extractor can be built and engaged
in a variety of configurations:

• A single centrifugal extractor can receive a load directly from

a tunnel washer, with side or in-line discharge directly into carts
or sent to automatic dryers via shuttle.

• Multiple centrifugal extractors can be used with a single

CBW batch washer in higher-production plants.

• A combination of centrifugal and membrane press

extractors can be configured for mixed-goods plants.

• 4 programmable extract speeds.

Reduces mat post-processing.

Low moisture retention is achieved with either cotton

or synthetic mats – even up to 4’ x 10’. That minimizes

post-processing requirements. Benefits are time, labor,
and fuel savings. During extraction, the machine

automatically distributes mats evenly inside the cylinder.
Moreover, the machine’s optional split extract cycle helps
prevent “water burst,” since sudden pressure is not
applied to pockets of water common with some types of
goods. With a steady stream of easily-handled batches of
mats, continuous production is achieved.

Other features...

• Microprocessor control links to washer and dryer

controls for completely automated system.

• Suspension system isolates vibration for high speed operation.

• Bearing housing supported 360° by massive ring-of-

steel design.

• Dynamic braking shortens turnaround time.
(No wearable discs or pads.)

®

• Links to Mildata

management (ask us for a brochure).

• Flat back Design eases maintenance and simplies

service.

computer system for total plant

SPECIFICATIONS

42032 48040
MXS M9V

Maximum extract speed - RPM (G force)

Dry weight capacity - lbs. (kg)
Cylinder diameter - ins. (mm)
Cylinder depth - ins. (mm)

Gross cylinder volume - cu. ft. (L)

Drive Motor - HP (kW)
Hydraulic Motor - HP (kW)
Overall Width - ins. (mm) +
Overall Depth - ins. (mm)
Stationary Overall Height - ins. (mm)
Unloading Overall Height - ins. (mm)

Approximate net weight - lbs. (kg)

+ Add 36 ins. (914 mm) for freestanding controls.

Specifications are approximate. Dimensions for 76039 with standard conveyor.

Specifications and appearance are subject to change without notice.

1000 (600)
up to 150 (68)
42 (1067)
32 (813)

25.7 (728)
30 (22)
10 (7.5)

104.63 (2657)

128.87 (3273)

103.25 (2622)
136 (3454)
12,000 (5442)

Centrifugal Extractor.

Milnor’s centrifugal extractor has cylinder speeds

up to 1000 RPM, producing 600 Gs for excellent

moisture removal. Pre-extract load distribution
speed minimizes out-of-balance conditions. Single­motor inverter produces a full range of speeds.

Paired with a Milnor tunnel washer, the centrifugal
extractor combines versatility with automation.

840 (480)

up to 250 (115)

48 (1219)
40 (1016)

41.9 (1186)
60 (45)

15 (11)

122.43 (3110)

166.4 (4227)

113.87 (2892)

159.68

14,200 (6441)

(4055)

Printed in U.S.A.
© Pellerin Milnor Corporation

Cl as s 5- 9 Br oc hu re B 22 SL 00005/12122

Pellerin Milnor Corporation
P.O. Box 400, Kenner, LA 70063-0400 USA

504-712-7656 • 800-469-8780
Fax: [phone]

E-mail: [e-mail]
www.milnor.com