Millwood Pines W000107055 Assembly Instructions

Caution : You must read this before you proceed

CHAIR

CAUTION : This Chair is NOT a TOY.
Keep your child / children at bay in the process of assembly.
For turning the Chair and to prevent damage to the Chair, 02 persons may be
needed to execute this action.

Page 1 of 9

Label Picture Description QTY

A Backrest Panel 1

B Seat Panel 1

C

D

E Leg Support Bar 1

Label Picture Description QTY

Right Leg Panel

1

(with Leveler)

Left Leg Panel

1

(with Leveler)

①

②

③

④

⑤

Short Bolt

3

(M8x30mm)

Long Bolt

7

(M8x50mm)

Screw

3

(M6x50mm)

Flat Washer

3

(M8.5/16x2mm)

Allen Key 1

Page 2 of 9

Before Beginning Assembly:

This Chair has multiple parts and may require up to 30 minutes to assemble. To give

Overview

Backrest Panel (A)

Left Leg Panel(D)

Leg Support Bar(E)

Right Leg Panel (C)

Seat Panel(B)

FRONT FACING

you an overview of the Chair parts, the above picture is to help you put the various
parts into perspective. Please read through the instructions below to familiarise
yourself with the parts and steps before assembly.

Page 3 of 9

Step 1

Page 4 of 9

Unpack and place all parts on a clean, non-marring surface.

Step 2

Lay down Backrest Panel (A) then attach Seat Panel (B) to Backrest Panel (A)
by using Bolt (①), Flat Washer (④) and secure by Allen Key (⑤)

Do not fully tighten the Bolts.

Step 3

A

5

Step 3.2

2

5

2

Step 3.1

D

Pre-fixed Iron Dowel

B

Position housing of Left Leg Panel (D) into pre-fixed iron dowel on Seat Panel
(B) as picture

3.1) Secure Left Leg Panel (D) to Seat Frame (B) by using Bolts(②) with Allen
Key(⑤)

3.2) Secure Left Leg Panel (D) to Backrest Panel (A) by using Bolts(②) with
Allen Key(⑤)

Do not fully tighten the Bolts.

Page 5 of 9

Step 4

5

ABC

D

2

5

Step 4.2

2

5

3

E

Step 4.1

With assistance from your adult partners, turn pre-assemble part in step 3 to
the other side
Place Leg Support Bar (E) into housing of Left Leg Panel (D)
Then, position housing of Right Leg Panel (C) into pre-fixed iron dowel on Seat
Panel (B) and Leg Support Bar (E) as picture

4.1) Secure Right Leg Panel (C) to Leg Support Bar (E) by using Screw (③)
with Allen Key(⑤)

4.2) Repeat same process in step 3.1 and 3.2 to Secure Right Leg Panel (C) to
Backrest (A) and Seat Panel (B)

Do not fully tighten the Bolts, Screws.

Page 6 of 9

Step 5

3

5

E

D

With assistance from your adult partners, turn the Chair back to normal flat ground
Secure Left Leg Panel (D) to Leg Support Bar (E) by using Screw (③) with Allen Key(⑤)

Do not fully tighten the Screw

Step 6

If wobble

Test again

30CM~50CM

Place the Chair right side up on a LEVEL SURFACE to see if it wobbles.
If it wobbles, lift the Chair to some 30cm to 50cm height from the ground.
Keep your feet and toes well away from the drop zone.
Drop the Chair freely and vertically with the four legs, hitting the ground, at the same time.
This Drop Test will help to ensure that all the Bolts, Screws and gaps all reach full
alignment status.
Test again for evenness on a LEVEL SURFACE.
If no wobbles are found, proceed to tighten all the Screws, and Bolts.

CAUTION: When tightening the Screws, and Bolts tighten sequentially. DO NOT
tighten any Bolt, or Screw fully and then move towards the next one. This could
cause the frame to warp.

If there are still wobbles, loosen the Screws and Bolts and execute this same drop tests.

If the Chair is not stable, it could lead to damage to the product.

Page 7 of 9

Step 7

Page 8 of 9

Your Chair is ready for use.
Please use adjustable foot for uneven floors.

This Chair can only be used on a flat, level surface.

Page 9 of 9