Miller DS60 User Manual
FEATURES AND CONTROLS
Camera Screws
#1004 DS60 Fluid Head (Flat Base)
#1003 DS60 Fluid Head (150mm Bowl)
O P E R A T O R ’ S M A N U A L
FLUID HEAD
Sliding Platform
Tilt Lock
Tilt Drag
Control
Eyepiece Leveller
Mount
DS-60
Stud
Camera Plate
Quick Release
Lever
Safety Tab
Counterbalance
Selectors
Pan Lock
Bubble Level
Pan Drag Control
Slide Lock
Pan Handle Clamp
Telescopic Clamp
Pan Handle
Tilt Safety Lock
Flat Base
(Mitchell Type)
Clamp Stud
(3/8”)
ACCESSORIES & COMPONENTS SERVICE, SALES & SUPPORT
Description Cat#
Camera Plate Assembly (EURO) #1060
3/8”w Camera Screw P0037
Handle Clamp Assembly P3810
Telescopic Pan Handle #690
Eyepiece Leveller Adaptor #383
Ø150 M12 Clamp Nut Assembly P5114
9V Battery P5901
WARRANTY
3 year parts and labour warranty.Please refer to warranty
card for complete details.
Miller Authorised Service Agents must carry out all service and repair work.
Failure to observe this requirement may void warranty. It is advisable to
notify Miller or a MIller Authorised Service Agent if a change of performance
is observed as a result of dropping or rough usage. For information regarding
sales and service of Miller products, or for your nearest Miller representative
please contact us via www.millertripods.com or at the following:
MILLER CAMERA SUPPORT EQUIPMENT
30 Hotham Parade, Artarmon, Sydney
NSW 2064 Australia
Tel: +61 2 9439 6377
Fax: +61 2 9438 2819
Email: sales@miller.com.au
MILLER FLUID HEADS (Europe) LTD.
Unit 12A, Shepperton Business Park
Govett Avenue, Shepperton
Middlesex TW17 8BA United Kingdom
Tel: +44 (0) 1932 222 888
Fax:+44 (0) 1932 222 211
Email: sales@millertripods-europe.com
MILLER CAMERA SUPPORT LLC (USA)
218 Little Falls Road, Cedar Grove,
New Jersey 07009-1231 USA
Tel: (973) 857 8300
Fax: (973) 857 8188
Email: sales@millertripods.us
WEBSITE www.millertripods.com
D5190-3
Ball Base
Clamp Nut
(M12)
Fig 1.
(150mm)
INTRODUCTION
The Miller DS60 uid head offers robust and versatile 150mm ball levelling
or Flat Base support in a portable system. The DS60 features 4-position
counterbalance plus 4-position selectable pan/tilt drag to support payloads
from 15-30kg (30-66lb). With rear mounted main controls, a quick-release
Euro camera plate and tilt safety lock, the DS60 is designed for operator
ease. The ‘true’ uid drag action complements these features to deliver
seamless transitions under all studio and location conditions.
SAFETY INSTRUCTIONS
• Before operation please read the operating instructions.
• This Fluid Head has been designed to be operated by qualied camera
operators.
• Ensure Tripod is set-up for maximum stability and is stable.
• Hold camera securely during all levelling, balancing or removing opera-
tions.
• Ensure sliding platform is locked before tilting uid head from horizontal •
Lock uid head in horizontal position using the tilt safety lock before tting
or removing payload, or whenever operator leaves the system.
• Do not adjust the counterbalance or drag settings without securing (hold-
ing) the pan handle.
• Do not release the TILT LOCK without holding the PAN HANDLE to prevent
accidental or sudden movement.
• Do not release the clamp nut without holdng either the head or the at-
tached camera.
• Do not exceed the maximum total payload of 30kg. (66lb)
• The operator is responsible for the safe operation of this piece of equip-
ment.
Fig 2.
TECHNICAL DATA
Weight 6.1kg (13lb)
Height 210mm (8.2”)
Width 260mm (10.2”)
Depth 200mm (7.8”)
Max Payload Capacity 30kg (66lb) (see CB Graph)
Mounting 150mm ball levelling (1003), or
Flat Base (1004)
Pan Drag 4-positionselectableuiddrag
Pan Range 360°
Pan Lock Positive lock calliper brake
Tilt Drag 4-positionselectableuiddrag
Tilt Range +75°/-75°
Tilt Lock Positive lock calliper brake
Safety Lock Steel pin tilt brake calliper lock
Counterbalance System 4-position
Counterbalance Range 15-30kg (30-66lb) (see CB graph)
Camera Plate QR Euro Plate - 80mmW x 120mmL
Camera Platform 100mm (+50/-50mm) Sliding range
OPERATING INSTRUCTIONS
3. CENTRE YOUR CAMERA ON HEAD
6. BATTERY REPLACEMENT
The operating instructions for the DS60 Fluid Head are described below.
Please read and understand these instructions before using this equip-
ment.
1. INSTALL AND LEVEL THE HEAD
1. Unscrew the CLAMP NUT from its threaded stud/hole. (see Fig. 3)
2. Place the head in your tripod and re-t the CLAMP NUT. Do not tighten
fully.
3. Level the uid head by centering the BUBBLE LEVEL. Then screw the
CLAMP NUT tight.
4. Note: If adjusting the level with your camera mounted, hold the camera
before loosening the CLAMP NUT.
Ball Base
(150mm)
or Flat Base
(Mitchell Type)
Tripod Bowl
(150mm)
or Flat Base
(Mitchell Type)
Bubble Level
1. With your camera attached to the uid head, hold the PAN HANDLE and
release the TILT LOCK and TILT SAFETY LOCK.
2. Turn the TILT DRAG CONTROL knob to position “1”. Turn the COUN-
TERBALANCE SELECTOR knob to position “1”.
3. Release the SLIDE LOCK lever and slide your camera forward or back-
ward until balanced over the centre axis of the uid head (see Fig.4). If
necessary, be prepared to stop your camera sliding suddenly. Your camera
will remain static when balanced.
4. Lock the SLIDING PLATFORM by turning the SLIDE LOCK clockwise
until rmly locked tight.
COUNTERBALANCE PERFORMANCE
The DS-60 illumination feature uses a standard long life alkaline 9V
battery. Under most operating conditions the battery will provide two
years of operation.
Miller approves the use of the following battery, GP25A or equivalent 9V
batteries.
To change the BATTERY:
1. Lift tab on BATTERY LID
2. Remove BATTERY
3. Insert new BATTERY, negative end (-) rst
4. Replace BATTERY LID by presing into opening. Check for proper
location of BATTERY LID.
5. Press the ILLUMINATION BUTTON to test operation. The BUBBLE
LEVEL will remain illuminated for 10 seconds, then switch off
automatically.
Battery Lid
Battery
Illumination Button
2. MOUNT YOUR CAMERA
Note that best camera control can be achieved by balancing the camera
centre of gravity (C of G) over the centre axis of the head.To achieve this
the DS60 is equipped with a SLIDING CAMERA PLATFORM
1. Ensure tilt is horizontal. Lock the TILT SAFETY LOCK.
2. Lock the PAN and TILT LOCKS (rotate both levers clockwise until
rm).
3. Remove the CAMERA PLATE by pulling downwards on the SAFETY TAB
while rotating the QUICK RELEASE to the left until it reaches the automatic
stop position (the CAMERA PLATE will pop up).
4. With accessories and battery tted, determine your camera’s Cof G by
the best method available (Eg: balance camera on a rod to nd balance
point).
5. Attach the CAMERA PLATE at the C of G point by fastening the CAMERA
SCREWS into your camera’s base or “tripod base plate”. These screws
should be tightened evenly and as far apart as possible to prevent movement between camera and uid head.
6. Attach your camera to the uid head by holding the camera slightly “lens
down” and placing the attached CAMERA PLATE under the front lip on
the top of the SLIDING PLATFORM. Lower the back of the camera until
the QUICK RELEASE knob locks. Ensure the QUICK RELEASE knob is
rmly seated.
7. Grip the PAN HANDLE rmly and then disengage the PAN and TILT
LOCKS and TILT SAFETY LOCK. Your camera should be rmly attached
with no free movement.
Fig 3.
Pan Handle
Fig 4.
C of G
CENTRE AXIS
Clamp Nut (M12) or
Clamp Stud (3/8”)
Slide Lock
Tilt Safety Lock
Fig 5.
4. COUNTERBALANCE YOUR CAMERA
The DS60 includes a variable counterbalance system that provides ngertip
control through its tilt range and allows the camera to be static at any angle
within that range. The counterbalance control can be set in one of four
positions depending on your payload.
1. Hold the PAN HANDLE and release the TILT LOCK.
2. Rotate the COUNTERBALANCE SELECTORS to setting position “4”.
3. Tilt the camera through its tilt range. Check that your camera remains
static in a tilted postion. If the Camera rotates from its tilted position, return
the camera to the horizontal position and a lower counterbalnce setting. Tilt
through the range again and check that the camera remains static in both
tilted forward and tilted backward positions. Note: You may need to adjust
the SLIDING PLATFORM to ensure forward and backward balance.
Note: If accessories are added or removed , re-balance by: adjusting the
COUNTERBALANCE SELECTOR, and/or adjusting the SLIDING PLA-
TORM position, or by re-positioning the CAMERA PLATE on your camera’s
base or “tripod base plate”.
5. DRAG CONTROL
1. The DS60 provides four (4) settings for the pan drag control. These
settings are indicated on the control knob. There are no half-stops. When
changing drag settings, pan and tilt movements must be stopped.
2. To achieve smooth diagonal movement, ensure that TILT and PAN DRAG
CONTROLS are on similar settings.
Fig 6.
7. CLEANING
WARNING: Do not immerse in any liquid.
WARNING: Do not use stiff brushes, abrasives or solvents.
The DS60 features protective coatings, dust and moisture seals and cor-
rosive resistant materials to ensure long and trouble free operation, even
in harsh environments. To ensure optimum performance throughut the life
of the head Miller recommends regular cleaning.
When the uid head has been used in harsh environments (such as sand,
mud, or salt water spray), wipe over with a soft damp cloth as soon as
possible. Usa a soft clean brush to clean crevices. Clean CAMERA PLATE
and SLIDING PLATFORM.
MAINTENANCE
With the exception of cleaning, the DS60 does not require additional
maintenance. Miller recommends periodic servicing by a Miller Authorised
Service Agent.
Miller Authorised Service Agents must carry out all service and repair work.
Failure to observe this requirement may void warranty.
STORAGE
When storing your DS60 for extended periods clean uid head and store in
a safe, dry place, away from direct sunlight. The uid head can be stored
horizontally or upright. However, do not store the head with the tilt locked.
Loading...