Miles Industries RF24IDN, RF24IDP Owner's Manual

RETROFIRE

US Patent no. 8,166,965

Direct Vent Fireplace Insert

RF24IDN (NG) & RF24IDP (LPG)

Installation and Owner’s Manual

INSTALLER

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

WARNING: If the information in these instructions is not followed exactly, a ﬁ re or explosion may result causing property damage, personal injury or loss of life.

Do not store or use gasoline or other ﬂ ammable vapors and liquids in the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light the appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ﬁ re department.

Installation and service must be performed by a qualiﬁ ed installer, service agency or the gas supplier.

Leave this manual with the appliance.

CONSUMER

Retain this manual for future reference.

Please read this manual BEFORE installing and operating this appliance.

This appliance may be installed in an after-market permanently located, manufactured (mobile) home where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁ ed kit is used.

This appliance is a domestic room-heating appliance. It must not be used for any other purposes such as drying clothes, etc.

This appliance is suitable for installation in a bedroom or bed sitting room.

Massachusetts: The piping and ﬁ nal gas connection must be performed by a licensed plumber or gas ﬁ tter in the State of Massachusetts.

Ce guide est disponible en français sur demande.

MILES INDUSTRIES LTD., British Columbia, Canada

Manufactured by

www.valorﬁ replaces.com

Table of Contents

FOR THE OWNER

Safety Precautions ............................................ 3

Safety and Your Fireplace ................................. 4

Owner’s Information .......................................... 5

Remote Control Operation.................................9

Options ............................................................13

Lighting Instructions.........................................14

Warranty ..........................................................32

FOR THE QUALIFIED INSTALLER

Warranty Card at the

Warranty Card at the back of this manual.

back of this manual.

Speciﬁ cations ..................................................15

Dimensions ...................................................... 16

Vent Conﬁ gurations .........................................17

Vent Termination ..............................................18

Existing Fireplace Preparation.........................20

Supply Gas Installation .................................... 21

Vent Liner Rough-in .........................................22

Appliance Preparation ..................................... 22

Firebox Installation .......................................... 23

Ceramic Fuel Bed Installation..........................25

Window Reﬁ tting and Checking.......................27

Remote Control Initial Set-up .......................... 27

Operation Check and Aeration Adjustment......28

Optional Cast Iron Fret Installation ..................28

Optional Bottom Cover Installation ..................29

Remote Control Handset Wall Holder

Installation .......................................................29

Wiring Diagram ................................................ 30

Approved Venting Components .......................31

Warranty ..........................................................32

Spare Parts......................................................33

The information contained in this installation

The information contained in this installation manual is believed to be correct at the time of

manual is believed to be correct at the time of printing. Miles Industries Ltd. reserves the right

printing. Miles Industries Ltd. reserves the right to change or modify any information or speciﬁ ca-

to change or modify any information or speciﬁ ca- tions without notice. Miles Industries Ltd. grants

tions without notice. Miles Industries Ltd. grants no warranty, implied or stated, for the installation

no warranty, implied or stated, for the installation or maintenance of your heater, and assumes no

or maintenance of your heater, and assumes no responsibility for any consequential damage(s).

responsibility for any consequential damage(s).

190–2255 Dollarton Highway, North Vancouver, BC, CANADA V7H 3B1

Designed and Manufactured by / for

Miles Industries Ltd.

Tel. 604-984-3496 Fax 604-984-0246

www.valorﬁ replaces.com

Safety Precautions

READ and UNDERSTAND all instructions carefully

before starting the installation. FAILURE TO FOLLOW

these installation instructions may result in possible ﬁ re hazard and will void the warranty.

Prior to the ﬁ rst ﬁ ring of the ﬁ replace, READ the

Owner’s Information section of this manual.

DO NOT USE this appliance if any part has been under water. Immediately, CALL a qualiﬁ ed service technician

to inspect the unit and to replace any part of the control system and any gas control that has been under water.

THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

Installation and repair should be PERFORMED by a

qualiﬁ ed service person. The appliance and venting

system should be INSPECTED before initial use and at

least annually by a professional service person. More frequent cleaning may be required due to excessive

lint from carpeting, bedding, etc. It is IMPERATIVE that

the unit’s control compartment, burner, and circulating

air passageways BE KEPT CLEAN to provide for

adequate combustion and ventilation air.

Always KEEP the appliance clear and free from

combustible materials, gasoline, and other ﬂ ammable vapors and liquids.

NEVER OBSTRUCT the ﬂ ow of combustion and ventilation air. Keep the front of the appliance CLEAR

of all obstacles and materials for servicing and proper operation.

Due to the high temperature, the appliance should be

LOCATED out of trafﬁ c areas and away from furniture and draperies. Clothing or ﬂ ammable material SHOULD NOT BE PLACED on or near the appliance.

Clothing or ﬂ ammable material SHOULD NOT BE PLACED on or near the appliance.

Children and adults should be ALERTED to the hazards of high surface temperature and should STAY AWAY to

avoid burns or clothing ignition.

YOUNG CHILDREN should be CAREFULLY SUPERVISED when they are in the same room as

the appliance. Toddlers, young children and others

may be susceptible to ACCIDENTAL CONTACT BURNS. A physical barrier is recommended if there

are at risk individuals in the house. To restrict access

to a ﬁ replace or stove, INSTALL AN ADJUSTABLE SAFETY GATE to keep toddlers, young children and

other at risk individuals out of the room and away from hot surfaces.

This unit MUST be used with a vent system as

described in this installation manual. NO OTHER vent system or components MAY BE USED.

This gas ﬁ replace and vent assembly MUST be vented directly to the outside and MUST NEVER be attached

to a chimney serving a separate solid fuel burning

appliance. Each gas appliance MUST USE a separate vent system. Common vent systems are PROHIBITED.

INSPECT the external vent cap on a regular basis to

make sure that no debris, plants, trees, shrubs are interfering with the air ﬂ ow.

The glass door assembly MUST be in place and sealed

before the unit can be placed into safe operation.

DO NOT OPERATE this appliance with the glass door

removed, cracked, or broken. Replacement of the glass door should be performed by a licensed or qualiﬁ ed

service person. DO NOT strike or slam the glass door. The glass door assembly SHALL ONLY be replaced

as a complete unit, as supplied by the ﬁ replace

manufacturer. NO SUBSTITUTE material may be used. DO NOT USE abrasive cleaners on the glass door

assembly. DO NOT ATTEMPT to clean the glass door

when it is hot.

TURN OFF the gas before servicing this appliance.

It is recommended that a qualiﬁ ed service technician perform an appliance check-up at the beginning of each heating season.

Any safety screen or guard removed for servicing

MUST BE REPLACED prior to operating this appliance. DO NOT place furniture or any other combustible

household objects within 36” of the ﬁ replace front.

BE CAREFUL not to put any decorating objects

sensitive to heat to close above or around the ﬁ replace as it gets very hot when operating.

DO NOT use this heater as a temporary source of heat

during construction.

This appliance is a DOMESTIC ROOM-HEATING AP- PLIANCE. It must not be used for any other purposes

such as drying clothes, etc.

State of California. Proposition 65 Warning. Fuels

used in gas, wood-burning or oil ﬁ red appliances, and the products of combustion of such fuels, contain chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. California Health & Safety Code Sec. 25249.6.

Safety and Your Fireplace

Please Read and Carefully Follow all Safety Warnings and

Operating Instructions Contained in Your Owners Manual

(Replacement Manuals are available by contacting our service department at 1-800-468-2567 or visit www.valorﬁ replaces.com).

Please Follow These Important Child Safety Precautions and Recommendations,

• Parts of your Valor Fireplace become

extremely hot while in operation.

• The glass viewing window

temperature can exceed 500 F

at full capacity. Momentary contact with a hot glass

surface can cause a severe burn, even if the ﬁ replace

is operating at reduced heating capacity.

• The glass window will remain hot

for an extended period of time after the ﬁ replace has been turned off. Ensure that children are prevented from touching the ﬁ replace during the cool down period.

• Toddlers and Young Children

must be closely supervised at all times when they are in the same

room as the operating ﬁ replace. They lack full awareness of danger and rely on your protection. Toddlers, in particular, do not have the motor

skills and response reﬂ exes to withdraw in the event of accidental contact with a hot surface.

• A physical barrier is strongly

recommended if there are young

children, or at-risk individuals in the house. Install an approved aftermarket safety gate to keep toddlers, young children and other at-risk individuals a safe distance from the ﬁ replace.

• Keep the remote control handset

out of reach of children at all times. A wall mount storage holster

is provided with your remote control handset.

• Ensure that the ﬁ replace, including

the pilot light, is completely turned off when children are present and

close supervision and safety barriers are not available—see page 8 of

Owner’s Information section.

• If the ﬁ replace is not going to be used

for the summer or any extended

period of time, remove the batteries

from the remote control handset and receiver. It is recommended that

batteries are replaced annually in any event—see page 7.

Owner’s Information

• • HOT HEARTH / FLOOR!

The hearth or ﬂ oor in front of the ﬁ replace may become very hot when the ﬁ replace heats. Do not use the hearth as a seat or shelf.

• • Some materials or items, although safe, may discolor, shrink, warp, crack, peel, and so on because of the heat produced by the ﬁ replace.

AVOID PLACING

candles, paintings, photos,

and other items

SENSITIVE TO HEAT

• • Solid wood ﬂ ooring in front of the ﬁ replace (if allowed) may shrink during the heating season due to heat.

OWNER’S INFORMATION

WARNING

EXTREMELY HOT!!!

• READ the SAFETY information on pages 3 and 4 of this manual BEFORE operating your gas heater.

• Some parts of your ﬁ replace are EXTREMELY HOT, particularly the GLASS window.

• DO NOT LET CHILDREN touch the glass or any parts of your ﬁ replace even after it is turned off as it is still hot.

• USE A SAFETY SCREEN or a GATE to reduce

the risk of severe burns.

• Keep the remote control handset OUT OF

REACH of children. HOT HEARTH / FLOOR!

in front of the ﬁ replace may become very hot when the ﬁ replace heats. Do not use the hearth as a seat or shelf.

Some materials or items, although safe, may discolor, shrink, warp, crack, peel, and so on because of the heat produced by the ﬁ replace.

AVOID PLACING

and other items 36 inches (0.9 m) around the ﬁ replace.

Solid wood ﬂ ooring in front of the ﬁ replace (if allowed) may shrink during the heating season due to heat.

Performance of LPG appliances may be affected by the quality of commercial gas supplied in your area.

candles, paintings, photos,

SENSITIVE TO HEAT

The hearth or ﬂ oor

within

Fireplace

Hearth

Do not put

furniture or other objects

in this space in front of

the replace:

36” (0.9 m)

Thank You ...

For purchasing a Valor by Miles Industries. Your new radiant gas heater is a technical appliance that must be installed by a qualiﬁ ed dealer. Each Valor ﬁ replace is fully tested during the production process for your safety and comfort.

Your unit has been professionally installed by:

Dealer Name: ________________________________

Phone Number :_______________________________

Should you encounter an operational problem, call your dealer immediately.

Do not try to repair the unit as you may cause an injury or damage the ﬁ replace.

This manual and particularly the preceeding and following pages contain very important information regarding the safe operation of your ﬁ replace as well as maintenance instructions.

Read carefully BEFORE operating your ﬁ replace and pay special attention to the SAFETY WARNINGS.

A heating gas appliance does require safe handling and for this reason, we very strongly recommend that no children be allowed to touch the ﬁ replace and its

controls at all times. Do install a screen or barrier

in front of the ﬁ replace to protect your children against severe burns.

Operating Your Fireplace for the First Time

When operating your new ﬁ replace for the ﬁ rst time, some vapors may be released due to the burning of curing compounds used in the manufacture of the appliance. They may cause a slight odor and could cause the ﬂ ames to be the full height of the ﬁ rebox, or even slightly higher, for the ﬁ rst few hours of operation.

It is also possible that these vapors could set off any smoke detection alarms in the immediate vicinity. These vapors are quite normal on new appliances. We recommend opening a window to vent the room. After a few hours use, the vapors will have disappeared and the ﬂ ames will be at their normal height.

Flame Supervision Device

For your safety, this appliance is ﬁ tted with a ﬂ ame supervision device which will shut-off the gas supply if, for any reason, the pilot ﬂ ame goes out. This device incorporates a ﬁ xed probe, which senses the heat from the pilot ﬂ ame. If the probe is cool, the device will prevent any gas ﬂ ow unless manually lighting the pilot. See full lighting instructions on page 14 of this manual.

OWNER’S

Check that Window Moves Freely After Reinstallation

Spring Loaded Fastening Studs (2)

1/4 Turn

DO NOT TOUCH THE GLASS WHILE IT IS HOT!

Let the ﬁ replace cool ﬁ rst before cleaning it.

INFORMATION

Owner’s Information

Cleaning

DO NOT TOUCH THE GLASS WHILE IT IS HOT!

Let the ﬁ replace cool ﬁ rst before cleaning it.

Important - Glass cleaning - Mineral deposits

One of the by-products of the combustion process in a gas appliance is a mineral which can show up as a white ﬁ lm on the ceramic glass of the viewing door.

The composition of the deposit varies widely from various locations and also from time to time in the same location. It seems this is associated with the varying sulfur content of the gas. You may have the problem for a time and then not see it for many months when it will reappear in your area.

We have discussed this problem with ceramic glass manufacturers and they cannot give us a deﬁ nitive answer to this problem. Dealers have tried various cleaning products with varying results. The following recommendations will not guarantee results in your particular case.

NOTE: This is a problem beyond Miles Industries’ control and is not covered under warranty.

• Clean the glass regularly as soon as you notice

the buildup (white ﬁ lm). If the ﬁ lm is left for a longer period of time, it will bake on. It is then much harder, if not impossible, to remove.

• NEVER use an abrasive cleaner on the ceramic glass. Any abrasion of the surface has the immediate effect of compromising the strength of the glass. An emulsion type cleaner is recommended.

• Use a soft damp cloth to apply the cleaner. Dry the glass with a soft, dry, preferably cotton cloth. Most paper towels and synthetic materials are abrasive to ceramic glass and should be avoided.

• Our dealers have had good results from the products listed below. We cannot, however, guarantee the results of these products.

Do not clean the glass while it is hot.

Always securely replace the window before lighting.

If broken, the glass pane may only be replaced as a complete window unit as supplied by the manufacturer.

It is necessary to remove the cast iron fret and brackets or the bottom cover before removing the window—see previous installation sections.

WARNING

» BRASSO, POLISH PLUS by KELKEM, COOK TOP CLEAN CREME

by ELCO, WHITE OFF by RUTLAND, TURTLE WAX

The window can be removed for cleaning by rotating the two fastening studs at the bottom corners 90 degrees to release, and swinging the bottom of the window unit outwards to unhook the top edge.

IMPORTANT: To ensure a safe operation, verify that

the bolts are hooked properly to the window tabs; then, pull out the top of the window and release it to insure the springs return it.

After reﬁ tting the window, apply light hand pressure against the window frame sides to bed-in the window seal.

If the Hot Glass Warning plate has been removed from the front lower corner of the window, reinstall it by sliding it between the glass and the frame as indicated.

Hot Glass Plate

Dust, etc. can be brushed from the ceramic fuel effects and ﬁ rebox walls after removing the front unit and opening the window. Dust etc. can also be removed from the burner using a soft brush after removing the

ceramic fuel effects. When cleaning, make sure that

no particles are brushed into the slots in the burner.

Owner’s Information

Pilot Flame

Thermocouple Probe must be in Flame

OWNER’S INFORMATION

Checks

A periodic check of the pilot and burner ﬂ ames should

be made. Check after the ﬁ re has been on for at least 30 minutes. The pilot ﬂ ame must cover the tip of the thermocouple probe. The main burner ﬂ ame pattern will vary from appliance to appliance depending on the type of installation and climatic conditions—see images below.

Correct Flame Picture

The appliance area must always be kept clear and free from combustible materials, gasoline and other ﬂ ammable vapors and liquids.

Inspect the vent terminal outdoors regularly to make sure that, snow, leaves, bushes, trees, etc, do not obstruct it.

Examine the vent system and terminal regularly. We recommend annually.

Remote Control Handset Wall Holder

Your ﬁ replace equipment includes a wall holder to store the handset. If it hasn’t be installed, refer to the instructions further on in this manual for the installation.

Batteries

WARNING

DO NOT ATTEMPT TO CHANGE THE BATTERIES WHILE THE FIREPLACE IS STILL HOT! Let

the ﬁ replace cool ﬁ rst before touching it.

in the off-season will extend the battery life. Should the batteries loose power, the control may be operated by manually turning the control knob at the valve or by turning off the valve at the switch.

To replace the batteries in the remote control receiver:

1. The receiver is located to the left of the valve and

it is retained to the ﬁ rebox by a Velcro tab. Grab

the receiver and pull it out from its location.

2. Slide and remove the receiver cover.

3. Replace the 4 AA alkaline batteries.

4. Replace the cover.

5. Put the receiver back in its position pushing it in

so it attaches to the Velcro tab.

Lighting, Operation and Rating Information

WARNING

DO NOT ATTEMPT TO TOUCH THE DATA PLATE WHILE THE FIREPLACE IS STILL HOT! Let the

ﬁ replace cool ﬁ rst before touching it.

The Lighting, Operation and Rating information is located on a plate at the left of the valve under the burner.

To access the plate, remove the cast fret or the bottom cover, grab the plate and take it out to read it. There is important information on both sides of the plate.

Servicing

If any attention is required for your appliance, contact your supplier quoting the model number. It will be helpful if the appliance’s serial number can also be quoted. This number is on the rating plate, which is located under the burner. The replacement parts are shown at the end of this manual. Please always quote the part number and description when requesting spare parts.

CAUTION

DO NOT USE a screwdriver or other metallic object to

remove the batteries from the receiver or the handset! This could cause a short circuit to the receiver.

Low batteries signal: see page 13. BEFORE changing the batteries, turn off the valve

using the manual On/Off switch —see instructions on

the following page.

The appliance uses four alkaline 1.5 V AA batteries for its remote control receiver and one 9 V alkaline battery for its handset. Batteries should last one to two seasons, depending on usage. Removing the batteries

OWNER’S INFORMATION

Owner’s Information

Fireplace Control Devices

There are three ways to control your ﬁ replace.

1. Thermostatic Remote Control;

2. Wall Switch (optional);

3. Manual On/Off Switch.

The manual On/Off switch must be ON for the ﬁ replace to function. It can be used to shut off the ﬁ replace in case of emergency—see next section.

The Thermostatic Remote Control can be programmed to function automatically—see pages 9–13.

The Wall Switch (optional) can be used to turn on, off and to increase or decrease the ﬂ ame height—see 1265WSK—Wall Switch Kit.

NOTE: The remote control in the AUTO mode will

override the wall switch.

OFF

Thermostatic Remote Control

Wall Switch (optional)

Manual On/Off Switch

Manual ON/OFF Switch: Press the O button.

OFF

Manual On/Off Switch

How to Ensure Your Fireplace Cannot Be Turned ON Inadvertently

You can use one of the two following methods to ensure that your ﬁ replace will not turn on when you don’t want it on.

First, ensure your ﬁ replace is turned off—including the pilot—and cold BEFORE going ahead.

• You can prevent your ﬁ replace from lighting by

pressing the O button on the manual ON/OFF switch

on the gas valve—see image above.

• Alternately, remove all batteries from the receiver as well as the battery from the handset.

How to Turn Your Fireplace OFF (including pilot)

Familiarize yourself with each of these methods before operating your ﬁ replace.

Handset and Wall Switch: Press and hold the OFF

button for a second. If the ﬂ ames are on, they go down and you hear the

valve motor wind down. You hear a clunk and a beep indicating that the valve has received the signal from the remote control.

Remote control

handset

Wall Switch

(optional)

Automatic Shut-Off (in certain conditions)

Your ﬁ replace’s remote control is equipped with an automatic shut-off mechanism which is activated in

certain conditions. See page 13 in the Remote Control Operation section for a description of this feature.

Remote Control Operation

Current

temperature

(F or C)

Current time (12 or 24 hour clock)

Modes (Manual, Temperature, Timer)

Handset sensor

Battery status

Current

programmed

period (Timer)

Period

start or end

(Temp, Timer)

OWNER’S INFORMATION

NOTE: Before using the remote control system for the ﬁ rst time, the receiver and the handset must be

synchronized. See the section Remote Control Initial Set-up on page 27 of this manual.

Display Overview

Note: In the TEMP or TIMER modes, the remote handset senses the room temperature and adjusts the ﬂ ame accordingly.

To communicate, the handset should be within 15 feet (4.5 meters) of the ﬁ replace.

Do not leave the handset on the mantel or hearth.

IMPORTANT: BEFORE YOU BEGIN, please note that on this system, the settings of time, temperature and automatic ON/OFF can only be programmed when the function display is ﬂ ashing. Be patient when programming as it can take a few seconds to set.

Large ame

Set (scrolls

through

modes and

settings)

OFF (returns

to set mode,

turns the burner

and the pilot o)

Handset Overview

button (ames up, sets hours, temperature)

Small ame button (ames down and o, sets minutes, temperature)

TO TURN ON APPLIANCE TO TURN OFF APPLIANCE

CAUTION

When pilot ignition is conﬁ rmed, motor turns automatically to maximum ﬂ ame height.

• On the valve, turn MAN knob on the ON, full counterclockwise position.

• Place ON/OFF switch (if equipped) in I (ON position).

• Simultaneously press the OFF and

(large ﬂ ame) buttons until a short beep conﬁ rms the start sequence has begun; release buttons.

• Continuing beeps conﬁ rm the

ignition is in process.

• Once pilot ignition is conﬁ rmed, there is main gas ﬂ ow.

• After main burner ignition the

handset will automatically go into manual (MAN) control mode.

• Press OFF button.

When the pilot is off, it will take 2

minutes before it can be lit again.

STANDBY MODE (Pilot Flame)

• Press and hold (small ﬂ ame) to set appliance at pilot ﬂ ame.

FLAME HEIGHT ADJUSTMENT

• In standby mode: Press and hold

(large ﬂ ame) button to increase ﬂ ame height.

OWNER’S INFORMATION

Remote Control Operation

• Press and hold (small ﬂ ame) button to decrease ﬂ ame height or to set the appliance at pilot ﬂ ame.

• For ﬁ ne adjustment tap the (large ﬂ ame) or (small ﬂ ame) buttons.

Express Low and High Fire

• Double-click (small ﬂ ame) button. “LO” will be displayed. NOTE: Flame goes to high ﬁ re ﬁ rst before going to designated low ﬁ re.

x 2

• Double-click (large ﬂ ame) button. Flame automatically goes to high ﬁ re. “HI” will be displayed.

x 2

SETTING ºC/24-HOUR OR ºF/12-HOUR CLOCK

• In MAN mode, press OFF and (small ﬂ ame) buttons until display changes from Farenheit/12-hour clock to Celsius/24-hour clock and vice versa.

SETTING THE TIME

• The time display will ﬂ ash after either:

» Installing the battery or » Simultaneously pressing the

(large ﬂ ame) and (small ﬂ ame) buttons.

• Press (large ﬂ ame) button to set the hour.

• Press (small ﬂ ame) button to set the minute.

• Press OFF or simply wait to return to MAN mode.

MODES OF OPERATION

• Brieﬂ y pressing the SET button

changes the mode of operation in the following order:

MAN

→ →

TIMER

→ → and back to .

TEMP

MAN

NOTE: Manual mode can also be reached by pressing

either the (large ﬂ ame) or the (small ﬂ ame) buttons.

MAN

• - Manual Mode - Manual

Flame Height Adjustment.

TEMP

• - Daytime Tempera- ture Mode (Appliance must be in

standby mode; pilot ignited) - The

room temperature is measured and compared to the set temperature. The ﬂ ame height is then auto- matically adjusted to achieve the Daytime Set Temperature.

TEMP

• - Nighttime Setback Temperature Mode (Appliance

must be in standby mode; pilot

ignited) - The room temperature

is measured and compared to the Nighttime Setback temperature. The ﬂ ame height is then automati- cally adjusted to achieve the Nighttime Setback Temperature.

TIMER

• - Timer Mode (Appliance

must be in standby mode; pilot

ignited) - The timers P1 and P2

(Program 1, Program 2) each can be programmed to go ON and OFF at speciﬁ c times. For instructions see Timer Programming Mode.

NOTE: The display shows the set temperature every

30 seconds.

Remote Control Operation

SETTING THE ON / OFF TEMPERATURES

SETTING THE “DAYTIME” TEMPERATURE Default Settings: (sun), 23ºC / 74ºF

TEMP

OWNER’S INFORMATION

SETTING THE “NIGHTTIME SETBACK” TEMPERATURE

Default Settings: (moon), “--” (OFF)

TEMP

• Brieﬂ y press SET button to scroll to

TEMP (sun) mode. Hold

TEMP

the SET button until the TEMP ﬂ ashes.

• Press (large ﬂ ame) button

to increase the Daytime Set Temperature.

• Press (small ﬂ ame) button

to decrease Daytime Set Temperature.

• Brieﬂ y press SET button to scroll to

TEMP (moon) mode. Hold

TEMP

the SET button until the TEMP ﬂ ashes.

• Press (large ﬂ ame) button to

increase Nighttime Setback Temperature.

• Press (small ﬂ ame) button to

decrease Nighttime Setback Temperature.

• Press OFF or simply wait to complete programming.

Tip

Set the different parameters when they are ﬂ ashing.

+ 25 hidden pages

Miles Industries RF24IDN, RF24IDP Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual