Miles Industries MF28EN, MF28EPLPG, MF28ENNG, MF28EP Instructions Manual

Madrona Free Standing Direct-Vent

Top or Rear Vent Stove

MF28EN (NG) / MF28EP (LPG)

Engine to be installed ONLY with the cast stove body

MFCS01 or MFCS02

Installation & Operating

Instructions

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

WARNING: If the information in these

instructions is not followed exactly, a re

or explosion may result causing property
damage, personal injury or loss of life.

Do not store or use gasoline or other

ammable vapors and liquids in the vicinity

of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light the appliance.

• Do not touch any electrical switch; do not
use any phone in your building.

• Immediately call your gas supplier from
a neighbor’s phone. Follow the gas
supplier’s instructions.

• If you cannot reach your gas supplier, call

the re department.

Installation and service must be performed

by a qualied installer, service agency or the

gas supplier.

PLEASE READ THIS MANUAL BEFORE
INSTALLING AND OPERATING THIS
APPLIANCE.

This appliance may be installed in an

after-market permanently located,

manufactured (mobile) home where not
prohibited by local codes.

This appliance is only for use with the type
of gas indicated on the rating plate. This
appliance is not convertible for use with

other gases, unless a certied kit is used.

This appliance is a domestic room-heating
appliance. It must not be used for any other
purposes such as drying clothes, etc.

This appliance is suitable for installation in a
bedroom or bed sitting room.

Massachusetts: The piping and nal
gas connection must be performed by a

licensed plumber or gas tter in the State of

Massachusetts. Also, see Carbon Monoxide
Detector requirements under “Safety and
Warning Information” on page 5.

4000973/07

©2006, Miles Industries Ltd.

Manufactured by

MILES INDUSTRIES LTD.

British Columbia, Canada

www.milesreplaces.com

Thank You ...

For purchasing the Madrona by Miles Industries. Your new radiant gas heater is a
technical appliance that must be installed by a qualied dealer. Each Madrona is fully
tested during the production process for your safety and comfort.

Your unit has been professionally installed by:

Dealer Name _______________________________________

Phone Number ______________________________________

Should you encounter an operational problem, call your dealer immediately.

Do not try to repair the unit as you may cause an injury or damage the replace.

2

Table of Contents

Safety & Warning Information......................................................4

Specications................................................................................7

Approval & Codes — Ratings — High Altitude
Installations— Supply Gas — Electrical

Dimensions & Clearances............................................................8

Dimensions — Hearth Requirements — Clearances

Venting..........................................................................................10

Top / Rear Outlet — Vent Material — Wall Thickness —
Framing Vent in Combustible Walls & Ceilings — Typical
Venting Components — How to Read the Venting Chart

— Venting Chart — Restrictors — Vent Termination

Installation................................................................................... 15

Fan (Blower) — Venting Conguration — Gas Line Routing

Packs Contents—Appliance & Castings.................................. 15

Appliance Preparation................................................................16

Window & Log Pack — Cast Base — Engine —Cast Side
Panels — Fixing Casting Side Panels & Engine — Lighting
Instructions Plate — Remote Control Receiver — Gas Pipe
& Connector — Receiver Position — Optional Fan (Blower)
— Venting Outlet — Top Spar — Front Hooks — Rear Log
Support

Supply Gas.................................................................................. 21

Ceramic Logs.............................................................................. 22

Window Retting.........................................................................23

Operation Check & Aeration Settings Adjustment..................

Aeration Settings — Air Shutter

Front & Top Installation.............................................................. 24

Remote Control Handset Wall Holder........................................25

Owner’s Information...................................................................

Operating Your Stove — Cleaning — Checks —
Batteries — Touch-up Paint — Servicing — Remote

Control Operation — Manual ON/OFF Switch

23

26

CONTENTS

Lighting Instructions.................................................................. 31

Wiring Diagram........................................................................... 32

Options........................................................................................ 33

Venting accessories................................................................... 34

Warranty......................................................................................

Replacement Parts.....................................................................

37

38

3

Safety & Warning Information

READ and UNDERSTAND all instructions carefully
before starting the installation. FAILURE TO FOLLOW

these installation instructions may result in possible re

hazard and will void the warranty.

Prior to the rst ring of the replace, READ the
Owner’s Information section of this manual.

DO NOT USE this appliance if any part has been under
water. Immediately, CALL a qualied service technician
to inspect the unit and to replace any part of the control

system and any gas control that has been under water.

THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

Installation and repair should be PERFORMED by a
qualied service person. The appliance and venting

system should be INSPECTED before initial use and at

least annually by a professional service person. More
frequent cleaning may be required due to excessive
lint from carpeting, bedding, etc. It is IMPERATIVE that
the unit’s control compartment, burner, and circulating
air passageways BE KEPT CLEAN to provide for
adequate combustion and ventilation air.

Always KEEP the appliance clear and free from
combustible materials, gasoline, and other ammable

SAFETY INFORMATION

vapors and liquids.

NEVER OBSTRUCT the ow of combustion and
ventilation air. Keep the front of the appliance CLEAR
of all obstacles and materials for servicing and proper
operation.

Due to the high temperature, the appliance should
be LOCATED out of trafc areas and away from
furniture and draperies. Clothing or ammable material
SHOULD NOT BE PLACED on or near the appliance.

Children and adults should be ALERTED to the

hazards of high surface temperature and should

STAY AWAY to avoid burns or clothing ignition. Young
children should be CAREFULLY SUPERVISED when

they are in the same room as the appliance.

This gas replace and vent assembly MUST be vented

directly to the outside and MUST NEVER be attached

to a chimney serving a separate solid fuel burning
appliance. Each gas appliance MUST USE a separate

vent system. Common vent systems are PROHIBITED.

INSPECT the external vent cap on a regular basis to

make sure that no debris, plants, trees, shrubs are
interfering with the air ow.

The glass door assembly MUST be in place and sealed
before the unit can be placed into safe operation.

DO NOT OPERATE this appliance with the glass door
removed, cracked, or broken. Replacement of the glass
door should be performed by a licensed or qualied
service person. DO NOT strike or slam the glass door.

The glass door assembly SHALL ONLY be replaced
as a complete unit, as supplied by the replace

manufacturer. NO SUBSTITUTE material may be used.

DO NOT USE abrasive cleaners on the glass door

assembly. DO NOT ATTEMPT to clean the glass door
when it is hot.

TURN OFF the gas before servicing this appliance.
It is recommended that a qualied service technician
perform an appliance check-up at the beginning of

each heating season.

Any safety screen or guard removed for servicing

MUST BE REPLACED before operating this appliance.

DO NOT place furniture or any other combustible

household objects within 36” of the replace front.

BE CAREFUL not to put any decorating objects

sensitive to heat on the stove or too close to the stove

as it gets very hot when operating.

DO NOT use this heater as a temporary source of heat

during construction.

This unit MUST be used with a vent system as
described in this installation manual. NO OTHER vent

system or components MAY BE USED.

NOTE: When operating your new replace for the rst time, some vapors may be released due to the burning

of curing compounds used in the manufacture of the appliance. They may cause a slight odor and could cause
the ames to be the full height of the rebox, or even slightly higher, for the rst few hours of operation. It is also
possible that these vapors could set off any smoke detection alarms in the immediate vicinity. These vapors are
quite normal on new appliances. We recommend opening a window to vent the room. After a few hours’ use, the
vapors will have disappeared and the ames will be at their normal height.

4

Safety & Warning Information

California

Massachusetts

State of California. Proposition 65 Warning. Fuels used in gas, wood-burning or oil red

appliances, and the products of combustion of such fuels, contain chemicals known to the
State of California to cause cancer, birth defects and other reproductive harm. California

Health & Safety Code Sec. 25249.6.

State of Massachusetts Carbon Monoxide Detector/Vent Terminal Signage
Requirements

For all side wall horizontally vented gas fueled equipment installed in every dwelling,
building or structure used in whole or in part for residential purposes, including those owned
or operated by the Commonwealth and where the side wall exhaust vent termination is less
than seven (7) feet above nished grade in the area of the venting, including but not limited
to decks and porches, the following requirements shall be satised:

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of
the side wall horizontal vented gas fueled equipment, the installing plumber or gastter

shall observe that a hard wired carbon monoxide detector with an alarm and battery back-

up is installed on the oor level where the gas equipment is to be installed. In addition, the
installing plumber or gastter shall observe that a battery operated or hard wired carbon

monoxide detector with an alarm is installed on each additional level of the dwelling,

building or structure served by the side wall horizontal vented gas fueled equipment. It
shall be the responsibility of the property owner to secure the services of qualied licensed
professionals for the installation of hard wired carbon monoxide detectors.

a. In the event that the side wall horizontally vented gas fueled equipment is installed in a
crawl space or an attic, the hard wired carbon monoxide detector with alarm and battery
back-up may be installed on the next adjacent oor level.

b. In the event that the requirements of this subdivision can not be met at the time of
completion of installation, the owner shall have a period of thirty (30) days to comply with
the above requirements; provided, however, that during said thirty (30) day period, a battery
operated carbon monoxide detector with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as
required in accordance with the above provisions shall comply with NFPA 720 and be ANSI/
UL 2034 listed and IAS certied.

3. SIGNAGE. A metal or plastic identication plate shall be permanently mounted to the

exterior of the building at a minimum height of eight (8) feet above grade directly in line

with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or
equipment. The sign shall read, in print size no less than one-half (1/2) inch in size, “GAS
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas
fueled equipment shall not approve the installation unless, upon inspection, the inspector

observes carbon monoxide detectors and signage installed in accordance with the

provisions of 248 CMR 5.08(2)(a)1 through 4.

SAFETY INFORMATION

5

Safety & Warning Information

Massachusetts

State of Massachusetts Carbon Monoxide Detector/Vent Terminal Signage
Requirements - Cont.

(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1
through 4:

1. The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented”
in the most current edition of NFPA 54 as adopted by the Board; and

2. Product Approved side wall horizontally vented gas fueled equipment installed in a
room or structure separate from the dwelling, building or structure used in whole or in

part for residential purposes.

(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM
PROVIDED. When the manufacturer of Product Approved side wall horizontally vented
gas equipment provides a venting system design or venting system components with
the equipment, the instructions provided by the manufacturer for installation of the
equipment and the venting system shall include:

1. Detailed instructions for the installation of the venting system design or the venting

system components; and

2. A complete parts list for the venting system design or venting system.

SAFETY INFORMATION

(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM
NOT PROVIDED. When the manufacturer of a Product Approved side wall horizontally
vented gas fueled equipment does not provide the parts for venting the ue gases, but
identies “special venting systems”, the following requirements shall be satised by the
manufacturer:

1. The referenced “special venting system” instructions shall be included with the
appliance or equipment installation instructions; and

2. The “special venting systems” shall be Product Approved by the Board, and the
instructions for that system shall include a parts list and detailed installation instructions.

(e) A copy of all installation instructions for all Product Approved side wall horizontally
vented gas fueled equipment, all venting instructions, all parts lists for venting
instructions, and/or all venting design instructions shall remain with the appliance or
equipment at the completion of the installation.

6

Specications

Approval &

Codes

Ratings

This appliance is certied to ANSI Z21.88b-2003/CSA 2.33b-2003 Vented Gas Fireplace
Heater standard for use in Canada and USA, and to CGA 2.17-91 High Altitude Standard in
Canada. This appliance is for direct vent installations.

Conversion between fuels may only be done using the approved conversion kits listed on
page 33. This appliance complies with CGA P.4.1 Testing method for measuring annual

replace efciencies.

The installation must conform to local codes or, in the absence of local codes, with the

National Fuel Gas Code, ANSI Z223.1 or the Natural Gas and Propane Installation Code
CAN/CGA-B149. Only qualied licensed or trained personnel should install this appliance.

This appliance, when installed with the optional circulating fan kit (blower), must be

electrically grounded in accordance with local codes, or, in the absence of local codes, with
the National Electrical Code, ANSI/NFPA 70 or the Canadian Electrical Code, CSA C22.1.

Model (Field convertible Top or Rear Vent Outlet) MF28EN MF28EP
Gas Natural Propane
Altitude (Ft)* 0-4,500 feet*
Input Maximum (Btu/h) 28,000 28,000
Input Minimum (Btu/h) 12,000 14,500
Manifold Pressure (in w.c.) 3.75 10.2
Minimum Supply Pressure (in w.c.) 5.0 11.0
Maximum Supply Pressure (in w.c.) 11.0 14.0

Main Burner Injector Marking 82-750 92-300
Pilot Injector Marking 51 30

SPECIFICATIONS

*High

Altitude

Installations

Supply Gas

Electrical

Input ratings are shown in BTU per hour and are certied without deration for elevations up

to 4,500 feet (1,370 m) above sea level.
For elevations above 4,500 feet (1,370 m) in USA, installations must be in accordance with

the current ANSI Z223.1 and/or local codes having jurisdiction. Heating value of gas in some
areas is reduced to compensate for elevation—consult your local gas utility to conrm.
For installations at elevations above 4,500 feet (1,370 m) in Canada, please consult
provincial and/or local authorities having jurisdiction.

Heater engine MF28EN is used with natural gas.

Heater engine MF28EP is used with propane gas.
The supply pressure must be between the limits shown in the Ratings section above.
The supply connection is 3/8” NPT female.

5/16” O.D.
tubing

5/16”

are

3/8” N.P.T.
Female

3/8” N.P.T.

The Madrona stove does not require an electrical power source unless it is tted with an
optional circulating fan—see page 19.

7

Dimensions

Dimensions & Clearances

Inlet collar

Ø 6-5/8”

Gas

inlet

position

3/8”
fem.
NPT

17-7/8”

x

DIMENSIONS

Exhaust

collar Ø 4”

4”

Center

line

28-1/2”

Supplied
with top
vent; eld

convertible
to rear vent

Hearth

Requirements

Gas

inlet

position

3/8”
fem.
NPT

23”

x

8-1/2”

27-1/2”

31-1/2”

14”

This unit is approved for mounting directly on combustible wood ooring. If installed directly
on carpeting, vinyl or soft combustible oor other than wood, it must be installed on a metal
or wood panel covering a minimum surface of 15” deep by 28” width.

26-1/8”

8

Dimensions & Clearances

Clearances

Min. 5”

Min. 5”

between

combustible

wall and

stove

Min. 5” between

combustible wall

and stove

between

combustible

wall and rear

of stove

17-7/8”

Corner clearances Wall clearances

Maximum 26” from wall for

projection of combustible

Minimum 12” between

stove and combustible

shelf or mantel

shelf or mantel

Min. 6” between

combustible wall

and side of stove

28-1/2”

CLEARANCES

31-1/2”

Min. 36”

Keep a minimum of

36” space in front

of stove free of

furniture or objects

Mantel / shelf clearances

40-1/2” minimum

17-7/8”

5” between
combustible wall
and back of stove

5”

43-1/2” minimum

26” maximum

Alcove clearances

9

Venting

Top / Rear

Outlet

Vent Material

Wall

Thickness

VENTING

Framing Vent

Combustible

Walls &

Ceilings

This unit is shipped with a top outlet collar which is eld-convertible to rear outlet—see page 20

for details.

This unit is approved for installation using 4” x 6-5/8” co-axial direct vent pipe and accessories
manufactured by Simpson Dura-Vent, Security and Selkirk—see list of approved venting pipes
and accessories on pages 33–36.

This unit may also be converted to co-linear (2–3”) venting for use in solid-fuel burning replaces
and chimneys using adapters and accessories—see list of approved venting pipes and
accessories on pages 33–36. Instructions for co-linear conversion are packaged with the co-linear
adapter.

Do not mix components from different vent manufacturers, with the exception of Valor’s 551DVK
Horizontal Termination Kit which can be used in combination with approved manufacturers’
venting pipes listed on pages 35–36. Follow the installation instructions supplied with the
individual venting components.

The appliance vent is suitable for penetrating a combustible wall assembly up to 14” (36 cm) in
thickness. A non-combustible wall can be of any thickness up to the maximum horizontal run of
vent pipe allowed for the particular installation.

When penetrating through combustible walls and ceilings, frame a minimum of 10” x 10” opening

in

to ensure that the insulation is kept clear of the vent pipe. Also, seal all joints between the wall
plates, the wall and the vent pipe. Follow the installation instructions supplied with the individual
venting components.

Align the vent
center to the
center of the
frame

10” (254mm)

10” (254mm)

10

Venting

Typical

Venting

Components

See list of approved venting pipes and accessories on pages 33–36.

Maximum pipe length:

24” (straight out with snorkel)
14” (45° elbow out with snorkel)

Snorkel required (min.

14” high) with horizontal
run through the wall

(no rise)

No more than one 45°
elbow allowed

VENTING

Through wall (without vertical rise)

Through wall (with vertical rise) Through roof

11

How to Read

the Venting

Chart

Venting

The chart below applies to top or rear outlet, roof or wall termination with a vertical rise.
All rear outlet venting without a vertical rise must be terminated by a snorkel.

1.

The total length of the vent pipe cannot exceed 40’ (12.2m).

2.

The minimum vertical height with roof termination is 8’ (2.45 m).

3.

Any combination of rise and run can be used as long as they are within the allowable
limits shown on the chart below.

4.

A maximum of 5 x 90° elbows—or equivalent (2 x 45° = 90°)—can be used.

5.

Each 90° elbow installed on the horizontal plane is equivalent to a 3’ horizontal pipe;
therefore, 3’ must be subtracted from allowable horizontal run. (45° elbow is equivalent
to 18” horizontal pipe.)

6.

All horizontal pipe runs must be graded 1/4” per foot upwards in the direction of the
exhaust ow.

7.

Co-linear venting in existing chimney systems is limited to 40’ vertical rise.

8.

Restrictors are not required for co-linear installations.

Roof termination

V3

VENTING

5” min.
between

pipe and

combustible
walls

Wall termination

40

38

36

34

32

30

28

26

24

22

Restrictor 75

20

18

16

14

VERTICAL RISE

12

5 x 90º ELBOWS

MAXIMUM

Allowable Vent

Congurations

NO

INSTALLATION

Example 1

Example 1
V Value = V1 (6’) + V2 (6’) + V3 (2’)= 14’

Not to scale

H Value = H1 (3’) + H2 (3’) = 6’
75% restrictor required

12

10

Restrictor 50

8

6

4

2

2 4 6 8 10 12 14 16 18 20

NO INSTALLATION

HORIZONTAL RUN

NO

RESTRICTORS

Venting

Restrictors

SOME INSTALLATIONS REQUIRE RESTRICTORS. For improved ame picture and

performance, this unit is supplied with two different sets of vent restrictors. The level of
restriction required depends on the vertical rise in the venting system and, to a lesser

degree, the horizontal run and number of elbows.

The amount of restriction is based on laboratory tests. The ideal restrictor position may
vary slightly, especially when the vent pipe length is near the limits of the acceptable
congurations for each type of restrictors.

The chart on the previous page shows the vent restrictor required relative to the length
of the vent pipe. Restrictors are not required for co-linear applications.

To install restrictors:

Remove every second screw from the exhaust ports in the top of the rebox.

1.

Install the restrictors with the removed screws.

2.

VENTING

50

Restrictor 50 Restrictor 75

75

OR

13

Venting

Horizontal

Vent

•

•

Termination

•

•

•

•

VENTING

The vent terminal must be located on an outside wall or through the roof.

This direct vent appliance is designed to operate when an undisturbed airow hits the

outside vent terminal from any direction.
The minimum clearances from this terminal that must be maintained when located on

an outside wall are shown in the gure below. Any reduction in these clearances could
result in a disruption of the airow or a safety hazard. Local codes or regulations may
require greater clearances.

The vent terminal must not be recessed into a wall or siding.

The vent terminal should be positioned where it will not be covered by snowdrifts.
Sidewall vent terminations within 7’ of grade require a terminal guard.

KEY VENT TERMINAL LOCATIONS - MINIMUM DISTANCES MINIMUM

CLEARANCE

Inches Cm
A Clearance above grade, verandah, porch, deck or balcony 12 30
B Clearance to window or door that may be opened 12 30

C Clearance to permanently closed window (recommended to prevent

condensation on window)

D Vertical clearance to ventilated soft located above the terminal within a

horizontal distance of 2 feet (60 cm) from the center-line of the terminal

E Clearance to unventilated soft 12 30

F Clearance to outside corner 12 30
G Clearance to inside corner 6 30

H Horizontal clearance to center-line of meter/regulator assembly located within 15

feet (4.6 m)below the terminal

I Clearance to service regulator vent outlet 36 90

J Clearance to non-mechanical air supply inlet to the building or the combustion air

inlet to any other appliance

K Clearance to a mechanical air supply inlet 72 180

L Clearance above paved sidewalk or a paved driveway located on public property

Note: A vent must not terminate directly above a sidewalk or paved driveway,
which is located between two single-family dwellings and serves both dwellings

M Clearance under a verandah, porch, deck or balcony

Only permitted if veranda, porch, deck or balcony is fully open on a minimum of 2

sides beneath the oor

Note: Local codes and regulations may require different clearances.

12 30

18 46

36 90

12 30

84 210

12 30

14

Venting

Vertical

Vent

Termination

Fan (Blower)

Roof

Pitch

Flat to 7/12 1'

Over 7/12 to
8/12

Over 8/12 to
9/12

Over 9/12 to
10/12

Over 10/12 to
11/12

Over 11/12 to
12/12

Over 12/12 to
14/12

Minimum
"H" (feet)

1.5'

2’

2.5’

3.25’

4’

5’

Installation

Allow for and install electrical wiring if there will be a blower to install. Ask the
homeowner if you are not sure.

INSTALLATION

Venting

Conguration

Gas Line

Routing

This unit is supplied with a top outlet and is eld convertible to a rear outlet. Plan
routing of vent taking into consideration stove and vent clearances, allowable vent
terminal locations BEFORE cutting a hole in the roof or wall. Avoid penetrating the
wall/roof at structural members.

Consider visibility of shut-off valve or step-down regulators, etc. when planning gas

line routing.

Packs Contents—Appliance & Castings

The Madrona Stove is supplied in three (3)

cartons.

In one carton is the engine.

•

In a second carton are the casting sides, the

•

top and the legs.
In a third carton are the casting front and base.

•

Unpack the cartons carefully. We strongly
recommend that you leave the engine sitting

on the packaging base in which it came to

avoid damaging the control valve, wires and
pipes already attached to the engine.

PACKAGING BASE to

WARNING!

LEAVE ENGINE ON

avoid damage to the

control valve, wires

and pipes.

Some parts are packed in the cardboard sleeve around the engine;
make sure you take them all out of the packaging. The engine carton
contains a list of all components included in the three cartons. Make
sure you have all the components before you start the installation.

15







Window &

Log Pack

Casting Base

Appliance Preparation

1.

Release the spring bolts at top and bottom
of the window by pushing and turning 1/4

turn.

2.

Lift the window and set it aside in a safe

place to avoid damage.

3.

Remove the log pack from inside the rebox

and set it aside with the window. Please
handle the logs carefully as they are made of
fragile material and can easily be damaged.

x 4

Rough-in the gas line and electrical wiring for a fan (if any).

1.

Decide where the stove should be positioned to avoid moving it once all the casting pieces

2.
are attached together.

Place the casting base upside down. Unscrew the bolts to insert the legs.

3.
Slide each leg under the head of its bolt.

4.
Tighten the bolts securely with a wrench.

5.

PREPARATION

Fix the casting base to the oor or

6.

hearth using bolts (not supplied)

through the casting feet—see the

bolting pattern below. (Required for
mobile homes only).

Detail

Appliance’s foot print

16

Appliance Preparation

Engine

Flip the base upside-down. Place the engine on the base at its approximate
nal position—see detail below. Center the engine using the holes at front of

the base as guidelines.

Detail

PREPARATION

Casting Side

Panels

On the casting side panels, release the top and bottom screws.

Drop a hinge pin on the back corner of base and drop the side panel on the pin.

1.

Rotate the panel towards the engine.

2.

Repeat with the other casting side panel.

3.

17

Appliance Preparation

Casting Side

Panels &

Engine

Lighting

Instructions

PREPARATION

Fixing

Plate

Adjust the position of the engine to locate the top and bottom screws of the side panels

1.

into the slots of the engine’s side bracket. Tighten the top and bottom screws.
Adjust the engine as required and x it to the casting base at bottom of its side

2.

brackets with the nuts and bolts provided.

The lighting instructions plate is attached to the back of the engine and may have slid out
of its slot. Reposition the plate if this is the case.

Remote

Control

Receiver

Gas Pipe &

Connector

Under the engine, the receiver box is clipped to the burner pipes to facilitate transportation.
Unclip the box and let it hang while you t the gas pipe.

Receiver hooked to burner pipes

Fit the pipe and connector supplied with the engine to the valve. Connect the gas line to
the inlet pipe.

3/8” gas line
connection

18

5/16” are

Appliance Preparation

Receiver

Position

Once the gas pipe is tted, clip the receiver on top of the casting crossbar on the base,
to the left hand side of the valve. Make sure the receiver box is oriented with its wires
towards the back and its sensor at the front.

Receiver & clip Receiver clipped to crossbar in nal position

PREPARATION

Optional Fan

(Blower)

If the Circulating Fan Kit (blower) is to be installed,

we suggest that you do it now.

Take the fan out of its package.

1.

Remove the mounting plate from the fan and

2.

discard it.
Position the fan in such a way that its exhaust

3.

is directed upwards, towards the space

between the inner and the outer walls of the

rebox.
Using 3 screws, x the fan to the rebox bracket.

4.

Fix the fan control box bracket provided to the

5.

control box with 2 screws.
Fix the bracket, with the control box attached, to

6.

the casting base of the stove from underneath.

With 2 screws from the burner plate, x the fan’s

7.

thermoswitch to the underside of the burner

plate, behind the pilot area.

See instructions with the 555CFK kit for

8.

complete details.

Fan control

box position

Fan control
box bracket

19

Appliance Preparation

Venting

PREPARATION

Outlet

!

If the appliance is to be vented from the top, it is ready for vent installation once the
engine is on the casting base.

If the appliance is to be vented from the rear, it must be converted. Follow these
simple steps:

1. Remove the following parts in this order:

a.

Dura-Vent collar, gasket and intake plate from the top of the appliance
(22 screws of the intake plate and 2 rear screws of the collar);

Exhaust collar (8 screws).

b.

NOTE: The gaskets are glued to the engine or the intake plate; it is not
necessary to separate them from the parts they are attached to. However,
if they need to be manipulated, BE CAREFUL not to damage them

because their material is fragile.

2. Re-install through the vent opening at the rear of the rebox in the
reverse order in which you took the parts out.

Co-linear

Applications

Top Spar

Front Hooks

For conversion of top or rear outlet collars to co-linear (2 x 3”) venting, refer to instructions
packaged with the 556CLA Co-linear Adapter.
NOTE: Co-linear venting may only be installed into solid-fuel burning replaces and chimneys.

Position the top spar on the side brackets located

1.
between the engine and the cast sides.

Fix the spar with four 3/8” pre-assembled screws

2.

provided.

Fix the 4 hooks to the inside
of the cast front with eight 8

mm screws provided.

Rear Log

Support

Fix the rear support log to the back of the rebox with the metal
screws taken from the back of the rebox (2) and from behind the

burner (2).

20

Connector

Pipes

Unions

Supply Line

Size

Sealant

Manual Shut-

off Valve &

Union

Test Pressures

>1/2 psig

(3.5kPa)

Test Pressures

≤1/2 psig

(3.5kPa)

Possible

Damages

Minimum

Pressure

Leak Test

Mandatory

Test Tapping

Location

Supply Gas

The gas supply inlet connection is a 3/8” NPT female connector. For detailed location

•

of this connector see drawing on page 7. If a circulating fan or isolating valve is to be

installed, adjust the routing of the gas line to suit.

Use only new black iron or steel pipes or copper tubing if acceptable—check local

•

codes. Note that in USA, copper tubing must be internally tinned for protection against

sulfur compounds.

Unions in gas lines should be of ground joint type.

•

The gas supply line must be sized and installed to provide a supply of gas sufcient to

•

meet the maximum demand of the appliance without undue loss of pressure.

Sealant used must be resistant to the action of all gas constituents including LP gas.

•

Sealant should be applied lightly to male threads to ensure excess sealant does not

enter gas lines.
The supply line should include a manual shut-off valve and union to allow the

•

appliance to be disconnected for servicing.
Pressure test the supply line for leaks.

•

The appliance and its individual shut-off valve must be disconnected from the

•

gas supply piping system during any pressure testing of that system at test

pressures in excess of 1/2 psig (3.5kPa).

The appliance must be isolated from the gas supply piping system by closing its

•

individual manual shut-off valve during any pressure testing of the gas supply

piping system at test pressures equal to or less than 1/2 psig (3.5kPa).

Failure to either disconnect or isolate the appliance during pressure testing may result

•

in regulator or valve damages and void the warranty. Consult your dealer in case of
damages.

The minimum supply pressure is

•

given in the Ratings section of this

manual—page 7.
All piping and connections must

•

be tested for leaks after installation
or servicing. All leaks must be
corrected immediately.

When testing for leaks:

•

Make sure that the appliance is

•
turned off.

Open the manual shut-off valve.

•

Test for leaks by applying a

•
liquid detergent or soap solution to all joints. Bubbles forming indicate a gas leak.

Never use an open ame to check for leaks.

Correct any leak detected immediately.

The pressure test tapping locations are shown in the gure above. A built-in non-

•

adjustable regulator controls the burner manifold pressure. The correct pressure
range is shown in the table in Ratings section of this manual on page 7. The pressure

check should be made with the burner alight and at its highest setting. See lighting

instructions section for full operating details on page 31.

SUPPLY GAS

21

Ceramic Logs

The ceramic logs are supplied in two packages. Unpack them very carefully to avoid
damaging the fragile material. Install the logs as shown below.

CERAMIC LOGS

22

Window Retting

To ret the window, place it on the
rebox frame and hold it in place while
pushing and turning its fastening studs

90 degrees.

Then, apply light hand pressure against

the window frame sides to bed-in the
window seal.

x 4

Operation

Check

Aeration

Settings

Air Shutter

Operation Check & Aeration Settings Adjustment

Turn the replace ame up and down using the remote control to conrm that the full range
of inputs is achieved—see the remote control operation instructions on pages 27–29.

Light the re and allow the unit to warm up for 10–15 minutes to evaluate the ame
picture. The burner is equipped with an adjustable shutter to control primary aeration. See
the gures below. The shutter is factory-set to an aeration gap which will give optimum
performance for the vast majority of installations. In a few unusual installations, the ame
picture may be improved by adjusting the aeration. The need for adjustment should be
determined only by operating the appliance with the ceramic logs and window installed.

Increasing aeration will cause the ames to appear more transparent and blue making

the ceramic logs glow more.

Decreasing aeration will cause the ames to appear more yellow or orange making the

ceramic logs glow less.

Too little aeration may result in black carbon forming and dropping into the rebox.

Air Shutter

OPERATION CHECK

Air Shutter
Retainer

Air Shutter in
Closed Position

Air Shutter in
Open Position

23

Front & Top Installation

Using pliers,
bend the four
hooks 1 to 2 mm
towards the
center of the
cast front.

adjustment

Installation

FRONT & TOP

Hooks

- Majolica
casting

Front

The Majolica casting front, because of the added thickness of the enamel nish,
may require adjustments of its hooks to ease its tting to the engine.

For an easier t, bend the 4 hooks 1 to 2 mm towards the center using pliers.

Hook the cast front to the side brackets located between the engine and the cast sides.

Details

Top Casting

Engine

Hook

Cast front

Side bracket

Place the top casting piece on the top of the stove ensuring the rear edge is ush
with the rear edge of the cast side panels. Fill in the vent space with the inll plate

if using a rear vent.

24

Remote Control Handset Wall Holder Installation

Packing Contents:

1 Wall Bracket A

2 Screws B

1 Screw C

2 Wall Anchor D

1 Spacer E
(detach before assembly)

1 Wall Bracket F

Switch Plate

Alternative 1

Alternative 2

Alternative 3

Remote

Control

Handset Wall

Holder

The remote control kit for this replace comes complete with a wall-mounted holder. This
holder is not required in all installations but is provided as an optional feature for those

customers who wish to mount the remote handset to the wall.

To install the holder to the wall, nd a convenient location and use the hardware provided
with the kit. See the diagram below for required hardware and congurations. Note that the
holder can be installed at the base of a light switch plate.

IMPORTANT. The location of the remote control handset is important to assure proper
temperature regulation. To obtain a constant temperature, we recommend that the handset
should be between 3 and 15 feet away from the appliance but not directly above it. We

also advise that the handset should be located away from any other heat source and not in

direct sunlight as this may affect the temperature sensor located in the remote handset.

HANDSET WALL HOLDER

25

Owner’s Information

Operating

Your Stove

For your safety, this appliance is tted with a ame supervision device which will shut­off the gas supply if, for any reason, the pilot ame goes out. This device incorporates a
xed probe, which senses the heat from the pilot ame. If the probe is cool, the device will
prevent any gas ow unless the MAN knob is in position MAN and the metallic core on the
valve is pushed in. See full lighting instructions on page 31 of this manual.

WARNING: Your stove becomes very hot when operating. Avoid placing decorative

objects sensitive to heat on the stove or within 36” around it.

Cleaning

OWNER’S INFO

It will be necessary to clean the glass periodically. During startup, condensation, which

is normal, forms on the inside of the glass and causes dust and lint to cling to the glass

surface. Initially, paint, while curing, may deposit a slight lm on the glass. We therefore
recommend that, during the rst few weeks of use, the glass be cleaned two or three times
with non-abrasive common household cleaners (such as dish soap) and warm water.

Ammonia based cleaners should NOT be used.

Subsequently, the glass should be cleaned two or three times a season depending on the
circumstances. Do not clean the glass while it is hot. Always securely replace the window

before lighting. If broken, the glass pane may only be replaced as a complete window

unit as supplied by the manufacturer.

To remove the window for cleaning, rotate its four fastening studs 90 degrees to release

and gently pull the window unit outwards—see page 16. Set aside in a safe place to avoid

damage.

To ret the window, place it on its frame and hold it in place while pushing and turning its
fastening studs 90 degrees. Then, apply light hand pressure against the window frame
sides to bed-in the window seal—see page 23.

Checks

Batteries

Dust can be brushed from the ceramic logs and rebox walls after removing the front unit
and opening the window. Dust can also be removed from the burner using a soft brush after
removing the ceramic logs. When cleaning, make sure that no particles are brushed into

the slots of the burner.

A periodic check of the pilot and burner ames
should be made. Check after the re has been
on for at least 30 minutes. The pilot ame
must cover the tip of the thermocouple probe.
The main burner ame pattern will vary from
appliance to appliance depending on the type

of installation and climatic conditions.

The appliance area must always be kept clear

and free from combustible materials, gasoline

and other ammable vapors and liquids.

Inspect the vent terminal outdoors regularly to make sure that snow, trees, bushes, leaves,

or other objects do not obstruct it.

Examine the vent system and terminal regularly. We recommend annually.

The appliance uses four 1.5 V AA batteries for its remote control receiver and one 9 V
battery for its handset. Batteries should last one to two seasons, depending on usage.

Removing the batteries in the off-season will extend the battery life. Should the batteries

lose power, the control may be operated by manually turning the control knob at the valve

or by turning off the valve at the switch.

Correct Flame Picture

26

Owner’s Information

Batteries

Touch Up

Paint

Servicing

Remote

Control

Operation

To replace the batteries in the remote control receiver, carefully pull the receiver

off its Velcro attachments on the cross beam.

If you need to touch up the paint on your cast unit, use the Stove Bright by Forrest
1990 Satin Black spray paint. Please note that it may be necessary to spray the
entire cast piece.

If any attention is required for your appliance, contact your supplier quoting the
model number. It will be helpful if the appliance serial number can also be quoted.
This number is on the rating plate, which is attached to the unit. The replacement
parts are shown at the end of this manual. Please always quote the part number and
description when requesting spare parts.

Your replace’s remote control helps you get the comfort, convenience and aesthetics you
want from your appliance. The “remote” controls your replace in different ways.

Note: If you would just like to turn your replace to the desired temperature, just press the

SET button to ☼temp or ☽temp and then, press and hold the SET button until the display

ashes; set the desired temperature by pressing the ▲ (up) and ▼ (down) buttons.

OWNER’S INFO

Operation

Modes

man MAN MODE—Manual Mode. The flame height can be adjusted

in the following manners:

Press the ▲ (up) button to turn on the main burner.

1.

Press the ▲ (up) button to increase the flame height.

2.

Press the ▼ (down) button to decrease the flame height or to

3.

go to pilot Standby position.

For fine adjustments, tap the ▲ and ▼ buttons.

NOTE: While pressing either button, a symbol indicating
transmission appears on the upper right hand corner of the display.

The receiver confirms transmission with an acoustic signal.

STANDBY MODE—Ignited pilot only.

☼temp TEMP MODE—Daytime Temperature Mode (appliance
must be in Standby mode; pilot ignited): The room temperature
is measured and compared to the set temperature. The flame

height is then automatically adjusted to achieve the Daytime set

temperature.

☽temp TEMP MODE—Nighttime Setback Temperature Mode (appliance must be in Standby

mode, pilot ignited): The room temperature is measured and compared to the Nighttime
Setback temperature. The ame height is then automatically adjusted to achieve the
Nighttime Setback temperature.

timer TIMER MODE—(appliance must be in Standby mode, pilot ignited): The Timer setting

allows you to set two burner ON times and two burner OFF times for every 24-hour period.

27

Owner’s Information

Operation

Modes

Changing the Mode of Operation

Briefly pressing the SET button changes the mode of operation in the
following order:

man

NOTE: MAN mode can also be reached by pressing either the ▲ or ▼

buttons.

In TEMP mode,

→

☼temp

☼ indicates the daytime temperature setting.

☽ indicates the nighttime temperature setting.

In TIMER mode,

☼ indicates the start time setting.

☽ indicates the stop time setting.

Time

OWNER’S INFO

To set the time, follow the steps below.

The display indicates °C/24-hour or °F/12-hour clock. To change from

1.

one to the other, press and hold both the OFF and ▼ buttons until the
display changes.

To set the time, hold down both the ▲ and ▼ buttons until the display

2.

ashes. Let go.

→

☽temp

→

timer

and back to

→

man.

Temperature

Quickly press the ▲ button to set the hour and the ▼ button to set the

3.
minutes.

Note: You must start setting the time while the display is ashing. If it
stops ashing, go back to 2.

Press the OFF button to return to manual mode or simply wait and it will

4.
automatically return to Manual mode.

Use this setting when you come in and want to enjoy a set temperature.

Select either the ☼temp MODE or the ☽temp MODE by briefly pressing

1.
the SET button.

Hold the SET button until the TEMP display flashes.

2.

Set the desired temperature with the ▲ or the ▼ buttons.

3.

Note: 4.5°C/40°F is the minimum temperature setting.

Press the OFF button or simply wait and the display will go to the

4.

temperature control mode.
Note: If you would like the Nighttime Setback temperature control to turn
off, decrease the ☽temp MODE setting until [---] appears on the display.

Your replace will reach the set temperatures and the remote handset
will check the temperature every ve minutes, adjusting the amount of

fuel needed to give you a steady, even heat.

The display must remain in TEMP mode on the remote handset.

5.

Note: Be patient with settings as it can take a few seconds to program.

28

Flame Height

Owner’s Information

In Standby mode, press the ▲ button to increase the flame height.

1.

Press the ▼ button to decrease the flame height or to set the appliance at the pilot flame.

2.

For fine adjustments, tap the ▲/▼ buttons.

Timer

It is possible to program two periods of time per day at which your replace will

turn on and off automatically.

For example, you can set your replace to turn on in the morning just before
you get up (P1 ☼ [start time]) and to turn off when you leave for the day (P1 ☽

[stop time]). Then, you can set your replace to turn on again at the end of the

day (P2 ☼ [start time]) and to turn off when you go to bed at night (P2 ☽ [stop
time]).

If you wish to set only one time period at which your replace will turn on and
off, program P2 ☼ [start time] and P2 ☽ [stop time] for the same time as P1 ☽

[stop time].

Select timer MODE by briefly pressing the SET button.

1.

Press and hold the SET button until TIMER is displayed on the lower right

2.
hand side.

Press and hold the SET button until P1 ☼ and the time display flashes. Set

3.

the start time by pressing the ▲ button for the hour and the ▼ button for the
minutes. Then, briefly press SET to P1 ☽ and set the stop time in the same

manner you just set P1 ☼.

Briefly press the SET button again for the next burner cycle time, which will

4.
be P2 ☼ and P2 ☽.

Once all four times are set, press OFF or simply wait to complete

5.

programming.

OWNER’S INFO

Low Battery

Indication

Poor

Reception

Handset /

Receiver

Match

Automatic

Standby Mode

The remote handset must remain in TIMER mode to function automatically.

6.

Remote handset: BATT will appear on the display when the battery needs to be
replaced.
Replace with one 9 V battery (alkaline recommended).

Receiver: When the batteries need to be replaced, three short ‘beeps’ will sound
when the motor functions. Replace with four 1.5 V batteries (alkaline recommended).
To replace the batteries in the receiver, unclip the receiver from the cross bar,
replace the batteries and re-clip the receiver on the cross bar.

If the reception is poor, remove the tape from the antenna on the receiver and stretch
the antenna toward an open area. This should improve reception.

The remote control handset and receiver are programmed to function together. In
case of a replacement of the handset or the receiver, you will need to reset the control

valve to allow them to function together. Contact your dealer for details

If there is no transmission from the handset to the receiver within a 6-hour period, the
appliance will go to STANDBY (pilot) mode.

29

Owner’s Information

Manual ON/
OFF Switch

In cases where you want to turn off your replace and cannot do it with the remote
control handset (misplaced, lost, dead batteries, etc.), you can turn off the appliance
with the manual switch located on the right hand side of the valve. Simply reach

under the front and activate the switch.

OWNER’S INFO

30

— O

ON

OFF

FOR YOUR SAFETY, READ BEFORE LIGHTING

WARNING:

If you do not follow these instructions exactly, a re or explosion may result

causing property damage, personal injury or loss of life.

A. This appliance has a pilot which must be lighted by hand or by remote control. Follow these instructions exactly.

To save gas, turn the pilot off when not using the appliance for a prolonged period of time.

B. BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the oor because

some gases are heavier than air and will settle on the oor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

C. Use only your hand to push in or turn the control knobs. Never use tools. If the knobs will not push in or turn by

hand, don’t try to repair them; call a qualied service technician. Force or attempted repair may result in a re or
explosion.

D. Do not use this appliance if any part has been under water. Immediately call a qualied service technician to

inspect the appliance and to replace any part of the control system and any gas control, which has been under

water.

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above.

5

Fig 1

2. SET ON/OFF SWITCH (1) TO “OFF” POSITION.

•

Wait ve (5) minutes to clear out any gas, then smell for gas, including near the oor. If you smell gas, STOP!
Follow “B” in the safety information above on this label. If you don’t smell gas, go to the next step.

3. AUTOMATIC IGNITION (Fig. 1): Locate the pilot (Fig. 3.) inside of rebox at left hand side.

•

ON/OFF switch (1) in ON position, MAN-knob (2) in ON position; set Flame Adjustment knob (3) to lowest

setting ().

•

On the remote control handset, press the star button () and up-arrow button () simultaneously; a short
acoustic signal conrms the start has begun.

•

Further short acoustic signals indicate the ignition process is in progress.

•

When the pilot is lit, the Flame Adjustment knob (3) will automatically rotate to the highest setting.

•

Press the down-arrow button () on the remote control handset to reduce the ame height.

4. MANUAL IGNITION (Fig. 2): With the window off, locate the pilot (Fig. 3) inside of rebox at left hand side.

•

ON/OFF switch (1) in ON position, MAN-knob (2) in MAN position.

•

Set Flame Adjustment knob (3) to the lowest setting ().

•

Push down the metallic core (4) with a pen or similar instrument; this will establish the pilot gas ow.

•

Light gas at the pilot (5) with a match.

•

Continue holding down metal core (4) for about 10 seconds; after release, pilot should remain lit.

•

If the pilot will not stay lit after several tries, turn the gas control knob (3) to OFF () and call your local
service technician or gas supplier.

•

Reinstall the window and set the MAN-knob (2) to ON; turn Flame Adjustment knob (3) up () or down ()
manually or use the up/down ()() buttons on the remote control handset to adjust the ame height.

Fig 2

Fig 3

TO TURN OFF GAS TO APPLIANCE

1. AUTOMATIC SHUT-OFF (using the remote control handset):

•

Press and hold the down-arrow button () on the remote control handset to shut-off the main burner gas ow.

•

Press OFF button on remote handset to shut-off the appliance, including pilot ame.

2. MANUAL SHUT-OFF (using only the ON/OFF switch (1) located to the right hand side of the valve):

•

Press O the ON/OFF switch (1) to shut-off the appliance, including pilot ame.

LIGHTING INSTRUCTIONS

31

Wiring Diagram

WIRING DIAGRAM

32

Options

Fuel

Cast Stoves

Safety

Screen

Venting

Fan (Blower)

Conversion

Kits

MF28EN—Natural Gas Installations
MF28EP—Propane Gas Installations

MFCS01—Madrona Stove Kit Standard Black
MFCS02—Madrona Stove Kit Majolica Brown

MFDKSG—Madrona Stove Door Kit Safety Guard

551DVK—Direct Vent Kit, for horizontal terminations with vertical rise.

See also venting accessories listed on pages 35–36.

555CFK—Circulating Fan Kit with 6’ c/w grounded cordset.

MA28NK—Conversion Kit to Natural Gas
MA28PK—Conversion Kit to Propane Gas

OPTIONS

551DVK

Venting accessories

The 551DVK horizontal termination kit (sold separately) detailed below includes
26” of usable pipe with a termination and through wall plates with vertical rise
only. This kit may be used as the nal through wall pipe and terminal with any of
the pipe manufacturers approved products listed on pages 35–36.

Important Installer Notice – Weather Sealing & Vapor
Barriers

It is the installer’s responsibility to ensure that vent installations through
exterior walls are caulked and weatherproofed in such a manner as to:

Prevent rain water from entering the wall from the weather side by

•

adequately caulking the outer vent plate to the exterior wall surface.
Prevent moisture inside the home from penetrating into the wall

•

structure by ensuring the inside wall plate is adequately sealed to
the inside vapor barrier.

Prevent rain water and moisture from entering the walls by sealing

•
the joints between the outer vent tube and the inner and outer wall

plates.

We recommend the use of a high quality polyurethane sealant.

33

Venting accessories

551DVK—Kit content

Pipe Terminal

Wall PlateInsulation Shields

Cut to length
depending on wall

thickness

This end ts over all different

manufacturers’ pipes shown in the list of
venting accessories on pages 33–34.

VENTING ACCESSORIES

12-1/8”

Wall plate with
insulation shield

Outer wall plate

11-3/4”

12-1/8”

11-3/4”

551DVK
terminal

34

Optional 835TG Terminal
Guard

Venting accessories

Approved Alternative Direct Vent Suppliers for Valor

Venting Parts Description

Co-axial kit, 26” long — — — — — 551DVK

Standard Co-axial 984 4DT-HC — — — —

Horizontal

Hign Wind Co-axial 985 — — SV4CHC — —

Standard Co-axial 980 4DT-VC — — HSDV4658-1313 —

Hing Wind Co-axial 991 — — SV4CGV — —

Extended Co-axial 930 — — — — —

Termination Caps

Vertical

Co-linear — — — 3PDVCV

Snorkel, 14” Rise 982 4DT-ST14 — — — —

Snorkel, 36” Rise 981 4DT-ST36 — — — —

Universal Adapter 3” Flex

Coupler

Co-linear Flex Connector 923F — — — — —

Models 530, 534, 535, AND

Miles Fireplaces’ Models MF28

Venting Parts Code / Availability by Manufacturer

VENT

SIMPSON

DURA-VENT

2150 — — — — —

SELKIRK

SECURE

RLH

INDUSTRIES

HS-C33U-99

HS-C33F-1313

559CLT

MILES

INDUSTRIES

VENTING ACCESSORIES

Couplers

Vent Adapters /

Liner

Flexible

Aluminum

Adjustable Pipe Length 4” x 6-5/8”

Co-axial to Co-linear

Adapter

Co-linear to

Co-axial Adapter

3” Diameter 2280 Series 3” ACFL

11” to

14-5/8”

12” to 17”

17” to 24”

4” to 10”

1-1/2” to 6”

1-1/2” to 12”

1-1/2” to 24”

Galvanized 911

Black 911B

Galvanized 912

Black 912B

Galvanized 917

Black 917B

Galvanized

Black 4DT-ADJ(B)

Galvanized

Black SV4LBA

Galvanized

Black SV4LBA12

Galvanized

Black SV4LBA24

923GCL — — — — 556CLA

923GK — — — — —

NOTE: 2-ply liner approved to CAN/ULC S635 suitable for
venting gas appliances. As manufactured by Z-Flex.

— — — — —

— — — — —

— — — — —

—

— — —

— — —

— — —

4DT-ADJ

— — — —

SV4LA

SV4LA12

SV4LA24

— —

— —

— —

35

Venting accessories

Venting Parts Description

Galvanized 945 — — —

Black 945B — — SV4EBR45

DV 45°

Elbows

DV 90°

Elbows

Pipes 4” x 6 5/8” ( ID x OD )

VENTING ACCESSORIES

Flashing

Galvanized Swivel 945G 4DT-EL45

Black Swivel 945BG 4DT-EL45(B) SV4EB45

Galvanized 990 — — —

Black 990B — — SV4EBR90

Galvanized Swivel 990G 4DT-EL90

Black Swivel 990BG 4DT-EL90(B) SV4EB90

6” long

9” long

12” long

18” long

24” long

36” long

48” long

Roof Flashing

Roof Flashing

Flat Roof Flashing 943F — — SV4F — —

Decorative Plate 940 4DT-CS — SV4PF — —

Cathedral Ceiling

Ceiling Firestop /

Galvanized 908 4DT-06

Black 908B 4DT-06(B) SV4LB6

Galvanized 907 4DT-09

Black 907B 4DT-09(B) —

Galvanized 906 4DT-12

Black 906B 4DT-12(B) SV4LB12

Galvanized 4DT-18

Black 4DT-18(B) —

Galvanized 904 4DT-24

Black 904B 4DT-24(B) SV4LB24

Galvanized 903 4DT-36

Black 903B 4DT-36(B) SV4LB36

Galvanized 902 4DT-48

Black 902B 4DT-48(B) SV4LB48

0/12-6/12

7/12-12/12

Wall Thimble 942 4DT-WT — SV4RSM — —

Storm Collar 953 4DT-SC — SV4AC — —

Support

Floor Support

Wall Strap 988 4DTWS — — — —

Venting Parts Code / Availability by Manufacturer

VENT

SIMPSON

DURA-VENT

943 4DT-AF6 — SV4FA — —

943S 4DT-AF12 — SV4B — —

941 4DT-CCS — — — —

963 4DT-FS —

SELKIRK

—

—

—

—

—

—

—

—

—

SECURE

SV4E45

SV4E90

SV4L6

—

SV4L12

—

SV4L24

SV4L36

SV4L48

SV4BF

SV4SD

RLH

INDUSTRIES

— —

— —

— —

— —

— —

— —

— —

— —

— —

— —

— —

— —

MILES

INDUSTRIES

Vinyl Siding Standoff 950 4DT-VS — SV4VS — —

Various Venting System Parts

Elbow Strap 989 4DT-OS — — — —

Termianl Guard 984SG — — — — 835TG

Notes: 1) Simpson Dura-Vent co-axial pipes and ttings require Valor 817VAK Starter Adapter to t Valor’s smooth collars. All other above

manufacturers’ collars will t directly to Simpson Dura-Vent or Valor’s smooth collars. 2) Follow instructions supplied with each manufacturer’s
components. 3) Unless otherwise specied, all the parts and assemblies from the above table are to be used with 4” x 6-5/8” pipes.

4) Termination caps manufactured by RLH Industries are from Homestyle Chimney Collection and can be ordered in one of the following

nishes: a) aluminium; b) black powder coated; c) solid copper.

36

Warranty

Limited

Lifetime

Warranty

Coverage

Two-Year

Parts

Warranty

Terms and

Conditions

Your Madrona Limited Lifetime Warranty applies to the lifetime of the initial owner and cannot be

passed on to subsequent homeowners. During the dened lifetime warranty and conrmation of
a bona de defect in components or workmanship under normal conditions and use of service,
Miles Industries Ltd. (the “Manufacturer”), or its designated distributors, will pay for the repair of,
or exchange the following parts or components:

Item Coverage

Exterior steel case Corrosion

Glass window Loss of structural integrity
Burner and connection pipes Corrosion and loss of structural integrity (not

discoloration)
Cast iron stove casing Corrosion
Firebox and heat exchanger Corrosion and loss of structural integrity (not

discoloration)

In addition, for two years from the date of purchase, the Manufacturer, at its option, can repair or
exchange all parts and components not listed above but that are found to have a bona de defect
in material or workmanship under normal conditions of use.

The warranty registration card must be completed by the initial owner and returned to the

1.

Manufacturer within 90 days of purchase.
Installation and maintenance must be performed by an authorized and trained dealer in

2.
accordance with the Manufacturer’s installation instructions.

The owner must comply with all operating instructions.

3.

The Manufacturer is not responsible for the labor costs to remove defective parts or re-install

4.

repaired or replacement parts.
The rst purchaser or user of the unit will be responsible for any shipping charges for

5.

replacement parts as well as travel time incurred by the dealer to perform the warranty work.
This warranty applies to non-commercial use and service and is void if it is apparent that there

6.

is abuse, misuse, alteration, improper installation, accident or lack of maintenance to the unit.
This warranty does not cover damage to the unit through:

7.

7.1 Improper installation, operational or environmental conditions.

7.2 Inadequate ventilation in the area or competition for air from other household equipment
or appliances.

7.3 Damage due to chemicals, dampness, condensation, or sulphur in the fuel supply lines

which exceeds industry standards.

This warranty does not cover glass, log breakage or damage to the unit while in transit.

8.
The Manufacturer does not allow anyone to extend, alter or modify this warranty and assumes

9.

no responsibility for direct, indirect or consequential damages caused by the unit. State or
provincial laws where the rst purchaser or user resides may provide specic rights to extend
this warranty and, if so, the Manufacturer’s sole obligation under this warranty is to provide

labor and/or materials in accordance with those laws.

WARRANTY

Discharge of

Liability

No Other
Warranty

After two years from the date of purchase, the Manufacturer may, at its option, fully discharge all
obligations under this warranty by paying to the rst purchaser/user the wholesale price of any
defective parts.

All obligations to repair this unit are dened in this warranty. Some states or provinces may
specically mandate additional warranties on the part of manufacturers, but in the absence of
such specic legislation, there is no other warranty or obligation expressed or implied.

37

Replacement Parts

Cast Stove
Parts

Description Part no. Part no. Description Part no. Part no.

Black Majolica Black Majolica

1 Base 4000926AH 4000926MJ 6 Fret 4000935AH 4000935MJ

2 Top Panel 4000928AH 4000928MJ 7 LH Side Panel 4000931AH 4000931MJ

3 Leg (4) 4000929AH 4000929MJ 8 Inll Plate 4000927AH 4000927MJ

4 RH Side Panel 4000930AH 4000930MJ 9 Hook (4) 4000990

5 Front 4000934AH 4000934MJ Hardware pack 4000883

8

2

7

4

REPLACEMENT PARTS

9

6

1

3

5

38

Replacement Parts

Engine Parts

Code Description Part no. Code Description Part no.

1 Log Set 4000603 30e Servo Motor 4001190

2 Rear Log 4000688 31 Front Log Brackets (2) 4000739

3 L/H Cross Log 4000690 32 Shutter Slider 4000759

4 Middle Cross Log 4000689 33 Burner Assembly 4000599

5 R/H Cross Log 4000691 34 Aeration Shutter 4000657
6 Front Log 4000692 35a Injector Elbow NG 4000738
7 Restrictor 50 (2) 4000949 35b Injector Elbow LPG 9730035
8 Restrictor 75 (2) 4000950 36 Burner Support Plate 4000579
9 Dura-Vent Intake Collar 4000925 37 Valve Tray 4000636

10 Intake Collar Gasket 4000942 38 Rear Gasket 4000642

11 Exhaust Collar Assembly 4000943 39 R/H Side Gasket 4000644
12 Exhaust Collar Gasket 4000938 40 Front Gasket 4000641
13 Intake Plate 4000908 41 L/H Side Gasket 4000643
14 Intake Plate Gasket 4000941 42 Olive 8mm 420K342

R/H Stove Back Corner 4000922 43 Olive Nut 220K567

15

L/H Stove Back Corner 4000923 44 Pipe Valve to Main Burner 4000600

16

17 Firebox Assembly 4000920 45 Tube Nut 220K558
18 Rear Log Support 4000621 46 Valve Mount 4000141

19a Burner Tray Assy NG 4000894 47a Pilot Assembly NG 4000727
19b Burner Tray Assy LPG 4000895 47b Pilot Assembly LPG 4000728

20 Window Assembly 4000919 48 Electrode 720A543
21 Heat Reduction Bafe 4000974 49 Pilot Tube 4000732

22 Fan Control Bracket 9000946 50 Extended Nut 720A200
23 Inlet Pipe 030A224 51 Pilot Gasket 4000715
24 Inlet Connector 220K997 52 Pilot Bracket 4000729

Top Spar 4000916 53 Thermocouple 4000061

25
27 GV60 Valve 4000873 54a Pilot Injector #51 NG 4000735
28 Receiver 4001188 54b Pilot Injector #30 LPG 4000736

29 Wiring Harness 4001187 55 Two-Flame Pilot Hood 4000730

30 Remote Control Handset 4001038 56 Switch Bracket 4001070

30a Switch with Cable 4001036 57 Receiver Clip 4001164
30b Interruptor Block 4001037
30c Ignition Cable 4001039 58 Handset Wall Holder 9000008

30d

Cable Interruptor/Receiver

4001035

not shown

Pilot Tube Connector 4001034

REPLACEMENT PARTS

39

Replacement Parts

50

1

7

2

3

4

6

20

5

21

18

17

75

8

16

9

10

11

12

13

14

15

REPLACEMENT PARTS

23

25

24

57

58

30e

30a

29

28

30d

30b

27

30

30c

19a/19b

54a/54b

41

55

53

52

51

50

31

33

36

46

32

48

22

49

40

45

56

31

34

35a/35b

37

38

39

42

43

44

47a/47b

40