Milan Technology T1E1-CF-01-LH, T1E1-CF-01, T1E1-CF-01-SE, T1E1-CF-01-SM User Manual

COMPLIANCE INFORMATION

UL Listed
C-UL Listed (Canada)
CISPR/EN55022 Class A

FCC Regulations

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at the user’s own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on
the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique
édicté par le ministère des Communications du Canada.

European Regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.

Achtung !

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes
Rundfunkstörungen auftreten, in weichen Fällen der Benutzer für entsprechende Gegenmaßnahmen
werantwortlich ist.

Attention !

Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des
interférences radioélectriques, il appartiendra alors à l’utilsateur de prende les measures spécifiques
appropriées

Trademark Notice

All registered trademarks and trademarks are the property of their respective owners.

Copyright Restrictions

© 1999-2001 TRANSITION Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means –
graphic, electronic, or mechanical – without written permission from TRANSITION Networks.

Printed in the U.S.A. 33112.E

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten

verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur

Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen

einschliesslich der gegenseitigen Anerkennung ihrer Konformität.

TRANSITION Networks T1E1-CF-01 series media converters encode and decode
T1 OR E1 signals over duplex fiber cables to extend the distance and transmission
reliability of high speed T1 and E1 data traffic.

T1/E1 Copper-to-Fiber

Media Converters

T1E1-CF-01

USER’S GUIDE

T1E1-CF-01

Provides an RJ-45 twisted pair
connector for T1 OR E1 signals, a set
of RX (receive) and TX (transmit) coax
connectors for E1 signals, and a set of
RX and TX ST connectors to 850 nm
multimode fiber-optic cable.

T1E1-CF-01(SC)

Provides an RJ-45 twisted pair
connector for T1 OR E1 signals, a set
of RX (receive) and TX (transmit) coax
connectors for E1 signals, and a set of
RX and TX SC connectors to 850 nm
multimode fiber-optic cable.

T1E1-CF-01(SM)

Provides an RJ-45 twisted pair
connector for T1 OR E1 signals, a set
of RX (receive) and TX (transmit) coax
connectors for E1 signals, and a set of
RX and TX ST connectors to 1300 nm
singlemode fiber-optic cable.

T1E1-CF-01(LH)

Provides an RJ-45 twisted pair
connector for T1 OR E1 signals, a set
of RX (receive) and TX (transmit) coax
connectors for E1 signals, and a set of
RX and TX ST connectors to 1300 nm
singlemode fiber-optic cable.

T1E1-CF-01 in the Network . . . . . . .2

Installation . . . . . . . . . . . . . . . . . . . .4

Operation . . . . . . . . . . . . . . . . . . . . .7

Fault Isolation and Correction . . . . .8

Cable Specifications . . . . . . . . . . . .10

Technical Specifications . . . . . . . . .11

Compliance Information . . . . . . . . .12

T1E1-CF-01 IN THE NETWORK

NOTE: THE T1E1-CF-01 REQUIRES A CSU BETWEEN THE MEDIA
CONVERTER AND THE PUBLIC TELEPHONE NETWORK.

Features

• Media converter is framing independent (as ESF vs D4) and supports
all common line codes, (AMI, B8ZS, HDB3).

• Distance extensions of 2 km 850 nm multimode or 8 km 1300 nm
singlemode.

• Jitter attenuators optimize Bit Error Rate (BER) performance.

• Dry relay contacts allow media converter to be tied into separate
alarm circuit

• All Ones Insertion (AIS), indicated by LEDs, on loss of signal at
copper and/or fiber interface.

TECHNICAL SPECIFICATIONS

Standards Emissions: CISPR A

T1/E1 Physical Layer: ITU-T, ANSI, AT&T, ETSI

Case Dimensions 4.75" x 3.0" x 2.0" (119mm x 76mm x 50mm)
Shipping Weight 3 pounds (1.4 kilograms)
Delay 400nsec round trip
Environment Temperature: 0-50°C (32° to 122° F )

Humidity 10-90%, non condensing
Altitude 0-10,000 feet

Power Supply Requirements Replace power supply with only the equivalent
input rating (see below) and output rating (unregulated 9 VDC).

TN PN Requirement Location

3507 240 volts, 50 hertz United Kingdom
3342 230 volts, 50 hertz Europe
3340 120 volts, 60 hertz USA/Canada/Mexico
3346 100 volts, 50-60 hertz Japan
3511 240 volts, 50 hertz Australia
3537 (with power cord: 3522) South Africa

NOTE: This product also can be powered by the Transition Networks E-MCR
series media converter rack.

Warranty Lifetime

DECLARATION OF CONFORMITY

Name of Mfg: Transition Networks

6475 City West Parkway, Minneapolis MN 55344 USA
Model: T1E1-CF-01 Series Copper-to-Fiber Media Converter
Part Number: T1E1-CF-01, T1E1-CF-01(SC), T1E1-CF-01(SM),

T1E1-CF-01(LH)

Regulation: EMC Directive 89/336/EEC

Purpose: To declare that the T1E1-CF-01 and T1E1-CF-01(SM) to which this

declaration refers is in conformity with the following standards.

EMC-CISPR 22: 1985 Class A; EN 55022: 1988 Class A; EN 50082-1:1992;
EN 60950 A4:1997; IEC 801.2, IEC 801.3, and IEC 801.4; IEC 950

I, the undersigned, hereby declare that the equipment specified above conforms to the

above Directive(s) and Standard(s).

_June 8, 1999_____

Stephen Anderson, Vice-President of Engineering Date

OR

T1 or E1

E1

T1 OR E1

Network Extension

UTP/STP

Fiber

T1 or E1

E1

E1

OR

CSU

T1 or E1

T1 or E1

To Telco

OR

To Telco