Milan Technology NDM-FTX-XX-01 User Manual

Download

Page 1

NDM-FTX-xxxxx-01

USER’S GUIDE

NDM-FTX-xxxxx-01 (standard) NDM-FTX-xxxxx-01(L) (low profile)

Fast Ethernet Fiber/Dual Media NICs

• Fast Ethernet

• Copper and Fiber

• 10/100Base-TX and/or 100Base-FX

Transition Networks NDM-FTX series fast Ethernet dual media NIC (Network Interface Card) provides a 10/100BaseTX copper port and a 100Base-FX fiber port for installation flexibility in a mixed-media environment. The dual

ports can also provide redundancy for critical applications. These NICs come in standard and low profile form factors, and include driver support for a variety of operating systems.

Part Number Port One - Copper

10/100Base-TX

NDM-FTX-ST-01 NDM-FTX-ST-01(L)

NDM-FTX-SC-01 NDM-FTX-SC-01(L)

NDM-FTX-MT-01 NDM-FTX-MT-01(L)

NDM-FTX-SC5-01 NDM-FTX-SC5-01(L)

NDM-FTX-SC20-01 NDM-FTX-SC20-01(L)

NDM-FTX-SB201-01 NDM-FTX-SB201-01(L)

NDM-FTX-SB202-01 NDM-FTX-SB202-01(L)

RJ-45 100 m (328 ft)*

Port Two - Duplex Fiber-Optic 100Base-FX

ST, 1300 nm multimode 2 km (1.2 miles)*

SC, 1300 nm multimode 2 km (1.2 miles)*

MT-RJ, 1300 nm multimode 2 km (1.2 miles)*

SC, 1310 nm single mode 5 km (3.1miles)*

SC, 1310 nm single mode 20 km (12.4 miles)*

SC, 1310 TX/1550nm RX single mode, single fiber 20 km (12.4 miles)*

SC, 1550 TX/1310 nm RX single mode, single fiber 20 km (12.4 miles)*

Optional accessories sold separately

Part Number Description

BTR-NDM-RPL RPL, Bootable ROM Chip BTR-NDM-PXE PXE, Bootable ROM Chip

*Typical maximum cable distance. Actual distance is dependent upon the physical characteristics of the network installation.

Installation . . . . . . . . . . . . . . . . . . .2

Cable Specifications . . . . . . . . . . .4

Technical Specifications . . . . . . . .5

Troubleshooting . . . . . . . . . . . . . . .6

Page 2

NDM-FTX Series Fast Ethernet Dual Media NIC

Installation

Checklist

Before installing the NDM-FTX, verify that the package contains the following items:

• NDM-FTX Board

• LAN Driver CD

Please notify your sales representative if any item is missing or damaged.

Description

The NDM-FTX module has a bootable ROM socket (ROM chip sold separately). The two LED indicators, LINK/ACT and FDX located on the bracket, show network/board link, activities, collision, and full-duplex statuses. See Figure 1.

Figure 1: LEDs and Boot ROM Socket

NDM-FTX module installation

CAUTION: Wear a grounding strap and observe electrostatic discharge precautions when installing the NDM-FTX module. Failure to observe this caution could result in damage or failure of the NDM-FTX module.

To install the NDM-FTX module, do the following:

Install the NDM-FTX module -- continued

5. Ensure that the module is firmly seated in the slot.

6. Use the screws from step “3” to secure the module to the workstation or file server housing.

NDM-FTX PCI module configuration

For motherboards with automatic PCI configuration:

• No specific setup is needed.

• You can enter the system BIOS setup menu to view or specify the interrupt (INT) line of the PCI slots.

For motherboards with bus master and interrupt jumpers:

• Enable bus master operation in a selected PCI slot and select an INT request line (IRQ) level, using the appropriate motherboard jumper.

• Enable I/O on the NDM-FTX, PCI slot.

PCI bus system and configuration

• Ensure that the PCI machine supports master slots, INT multiple sharing and timing compatibility.

• DO NOT install NDM-FTX in PCI slave slots. Please refer to your PCI system manual and select the appropriate configuration settings.

• When installing multiple NDM-FTX boards in a server station, you should correctly configure the IRQ settings of the PCI slot.

• Up to four NDM-FTX modules can be installed in a PCI file server running NetWare operating system.

• NDM-FTX server modules share the same INT line with the driver supporting multiple INT services at a time. The IRQ of each NDM-FTX module should not conflict with other boards.

• Operation in full or half-duplex mode is configured by LAN driver options. The operating mode should match the working status of the remote link device.

• Use EMM386 version 4.49 or higher, and install both DOS and EMM386 from the same DOS package to avoid software problems.

Important: Install the NDM-FTX module in a “master slot” only.

1. Locate a master slot on the PC workstation or file server.

2. Remove the cover from the PC workstation or file server—keep all screws.

3. Remove and keep the screws holding the cover over the installation slot.

4. Carefully slide the NDM-FTX module into the “master slot,” aligning the module with the slot guides.

Tech Support: 1-800-260-1312 International: 00-1-952-941-7600, 24 hours

techsupport@transition.com -- Click the “Transition Now” link for a live Web Chat.

Page 3

NDM-FTX Series Fast Ethernet Dual Media NIC

Cable Specifications

Copper cable

10BASE-T UTP Category 3, 4, 5 or higher 100Base-TX UTP Category 5 or higher Gauge: 24 to 22AWG Attenuation: 22.0 dB /100m @ 100 MHz

• Straight-through MDI twisted-pair cable must be used.

• Shielded STP or unshielded UTP twisted-pair cable may be used.

• Pins 1 and 2, 3 and 6 are the two active pairs in an Ethernet network.

• RJ-45 Pin-out: Pin 1 = TD+, Pin 2 = TD-, Pin 3 = RD+, Pin 6 = RD-

• Use only dedicated wire pairs for the active pins:

(e.g., blue/white and white/blue, orange/white and white/orange, etc.)

• DO NOT use flat or silver satin wire.

Straight-Through Cable

Twisted Pair #1

Twisted Pair #2

The physical characteristics must meet or exceed the IEEE 802.3 specification.

1 2

3 6

Fiber cable

Bit error rate: <10-9 Single mode fiber (recommended): 9 µm Multimode fiber (recommended): 62.5/125 µm Multimode fiber (optional): 100/140, 85/140, 50/125 µm

NDM-FTX-ST-01(x), NDM-FTX-SC-01(x), NDM-FTX-MT-01(x) 1300 nm multimode Fiber optic transmitter power: min: -19.0 dBm max: -14.0 dBm Fiber optic receiver sensitivity: min: -31.0 dBm max: -17.0 dBm Link budget: 12.0 dB

NDM-FTX-SC5-01(x) 1310 nm single mode Fiber optic transmitter power: min: -19.0 dBm max: -14.0 dBm Fiber optic receiver sensitivity: min: -31.0 dBm max: -7.5 dBm Link budget: 12.0 dB

NDM-FTX-SC20-01(x) 1310 nm single mode Fiber optic transmitter power: min: -15.0 dBm max: -8.0 dBm Fiber optic receiver sensitivity: min: -31.0 dBm max: 0.0 dBm Link budget: 16.0 dB

NDM-FTX-SB201-01(x) 1310 TX/1550 RX nm single mode

Fiber optic transmitter power: min: -14.0 dBm max: -8.0 dBm Fiber optic receiver sensitivity: min: -32.0 dBm max: 0.0 dBm Link budget: 18.0 dB

1 2

3 6

single stand

Fiber cable -- continued

NDM-FTX-SB202-01(x) 1550 TX/1310 RX nm single mode

Fiber optic transmitter power: min: -14.0 dBm max: -8.0 dBm Fiber optic receiver sensitivity: min: -32.0 dBm max: 0.0 dBm Link budget: 18.0 dB

The fiber optic transmitters on the device meet Class I Laser safety requirements per IEC825/CDRH standard and comply with 21CRF1040.10 and 21CRF1040.11.

single stand

Technical Specifications

For models NDM-FTX-xxxxx-01 and NDM-FTX-xxxxx-01(L)

Standards: IEEE 802.3 Expansion bus standard: PCI 2.1, 2.2 Data rate: 10/100Mpbs twisted pair media

100Mbps fiber media

LED: LINK/ACT (on the bracket)

ON = communication link; flashing = activity on link FDX (full duplex link); ON = full duplex link

Drivers: • NetWare Server 4.1x, 5.x

• Netware DOS Client ODI

• Windows 95, 98, 2000, 2003, XP, NT4.0

• Linux Boot server support: Novell RPL Boot ROM; PXE Boot ROM PCB dimensions: 2.5” W x 5.9” D x 0.85” H

(63.5 mm W x 149.9 mm D x 21.6 mm H)

Weight: 3 oz. (91g) approximate Power consumption: 1.0A @ +5VDC MTBF 198,853 hours (Bellcore7 V5.0) Operating temp 0°C to 50°C (32°F to 122°F) Storage temp: -25°C to 85°C (-13°F to 185°F) Humidity: 5% to 90%, non-condensing Altitude: 0 to 10,000 feet Warranty: Lifetime

WARNING: Visible and invisible laser radiation when open: DO NOT stare into the beam or view directly with optical instruments. Failure to observe this warning could result in damage to your vision or blindness.

CAUTION: than those specified herein may result in hazardous radiation exposure.

The information in this manual is subject to change without further notice.

Use of controls, adjustments, or the performance of procedures other

Tech Support: 1-800-260-1312 International: 00-1-952-941-7600, 24 hours

techsupport@transition.com -- Click the “Transition Now” link for live Web chat.

Page 4

NDM-FTX Series Fast Ethernet Dual Media NIC

Troubleshooting

Diagnostics LEDs and Boot ROM

LEDS

The LINK/ACT LED lights when a fiber cable or twisted pair cable connection is good. It blinks to indicate activity.

The collision and full-duplex LED report board operating status.

Boot ROM

To add the remote boot feature to a workstation, insert the Boot ROM into the ROM socket. See Figure 1 on page 2.

After power UP, the LINK/ACT LED should light; if not, check the following:

1 Confirm that the NDM-FTX module is properly inserted into the PC

workstation master slot or file-server master slot.

2 Confirm that the PC workstation or the file server is properly connected to

a power source and with the power source turned ON.

3 Check the fiber cable and twisted-pair copper cables for proper connection.

4 Contact Tech Support: 1-800-260-1312, Int’l: 00-1-952-941-7600 if those

steps fail to produce the desired result.

Note: To connect this device to a router, bridge, or switch, please refer to the

corresponding technical manual for the device.

Declaration of Conformity

Name of Mfg: Transition Networks, 6475 City West Parkway,

Model: NDM-FTX-xxxxx-0l and NDM-FTX-xxxxx-0l(L) Network Interface

Part Number: NDM-FTX-ST-01(x), NDM-FTX-SC-01(x), NDM-FTX-MT-01(x),

Regulation: EMC Directive 89/336/EEC

Purpose: To declare that the NDM-FTX-xxxxx-01 and NDM-FTX-xxxxx-0l(L), to

CISPR 22:1997+A1:2000; EN 55022:1998+A1:2000 Class A; FCC Part 15 Subpart B; 21CFR

subpart J

I, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s) and

Standard(s).

Stephen Anderson, Vice-President of Engineering Date

Minneapolis, MN 55344 U.S.A.

Cards

NDM-FTX-SC5-01(x), NDM-FTX-SC20-01(x), NDM-FTX-SB201-01(x), NDM-FTX-SB202-01(x)

which this declaration refers, is in conformity with the following standards:

June 30, 2005

Technical support

Technical support is available at techsupport@transition.com

• US and Canada: 1-800-260-1312 (24 hours)

• International: 00-1-952-941-7600 (24 hours)

Transition now

Chat live via the Web with Transition Networks Technical Support. Log onto www.transition.com and click the Transition Now link.

Web-based seminar

Transition networks provides seminars via live, web-based training. Log onto www.transition.com and click the Learning Center link.

Ask a question anytime by sending an email to our technical support staff: techsupport@transition.com

Address

Transition Networks

6475 City West Parkway

Minneapolis, MN 55344, U.S.A.

Telephone: 952-941-7600,

Toll free: 800-526-9267

Fax: 952-941-2322

Tech Support: 1-800-260-1312 International: 00-1-952-941-7600, 24 hours

techsupport@transition.com -- Click the “Transition Now” link for live Web chat.

Page 5

Compliance Information

CISPR22/EN55022 Class A, CE Mark, CISPR22/EN55022 Class A + EN55024, CE Mark

FCC regulations

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at the user's own expense.

Canadian regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the radio interference regulations of the Canadian Department of Communications. Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la Class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada.

European regulations

Caution: This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures. Achtung! Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für Gegenmaßnahmen verantwortlich.

Attention! Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des interférences radioélectriques, il appartiendra alors à l'utilsateur de prende les measures spécifiques appropriées.

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EGMitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer Konformität.

Trademark notice

All registered trademarks and trademarks are the property of their respective owners.

© 2004-2005 Transition Networks. All rights reserved. No part of this work may be reproduced or used in any form or by any means—graphic, electronic or mechanical—without written permission from Transition Networks

Printed in the US Manual Part Number and Rev.

33332.A