Milan Technology CERTXFX01, CERTXFX01-SC, CERTXFX01-SM User Manual

COMPLIANCE INFORMATION

UL Listed
C-UL Listed (Canada)
CISPR/EN55022 Class A

FCC Regulations

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the user will be
required to correct the interference at the user’s own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on
the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique
édicté par le ministère des Communications du Canada.

European Regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.

Achtung !

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses Gerätes
Rundfunkstörungen auftreten, in weichen Fällen der Benutzer für entsprechende Gegenmaßnahmen
werantwortlich ist.

Attention !

Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des
interférences radioélectriques, il appartiendra alors à l’utilsateur de prende les measures spécifiques
appropriées

Trademark Notice

All registered trademarks and trademarks are the property of their respective owners.

Copyright Restrictions

© 1999 TRANSITION Networks.
All rights reserved. No part of this work may be reproduced or used in any form or by any means –
graphic, electronic, or mechanical – without written permission from TRANSITION Networks.

Printed in the U.S.A. 33113.A

Designed to be installed in the TRANSITION Networks E-MCC-1600 Media
Converter Chassis, C/E-R-TX-FX-01 series redundant Fast Ethernet

™ media converters

connect 100BASE-TX unshielded twisted pair copper to 1300 nm 100BASE-FX
multimode OR to 1300 nm 100BASE-FX singlemode fiber. In the event of a failure
in the primary copper or fiber connection, a fully redundant secondary connection
is made available to the failed copper or fiber connection. Also, the copper and
fiber media converter interfaces operate independently, so that a failure on one
interface will not force a failure on the other interface.

Switches at the side of the media converter allow selection of auto-negotiation and
of full/half-duplex. Also, a port select timer (PST) switch* allows the network
administrator to set different timer values (used when a primary connection is lost
and a secondary connection is made) at each end of the copper/fiber interface.

(*See note on page 5.)

Minneapolis, MN 55344 USA

Redundant Fast Ethernet

™

100BASE-TX/100BASE-FX 1300 Nanometer

Slide-In-Module Media Converters

C/E-R-TX-FX-01, C/E-R-TX-FX-01(SC), C/E-R-TX-FX-01(SM)

USER’S GUIDE

C/E-R-TX-FX-01

Provides two (2) RJ-45 twisted pair
100BASE-TX connectors and two (2)
sets of RX (receive) and TX (transmit)

ST 100BASE-FX connectors to 1300
nm multimode fiber-optic cable.

C/E-R-TX-FX-01(SC)

Provides two (2) RJ-45 twisted pair
100BASE-TX connectors and two (2)
sets of RX (receive) and TX (transmit)

SC 100BASE-FX connectors to 1300
nm multimode fiber-optic cable.

C/E-R-TX-FX-01(SM)

Provides two (2) RJ-45 twisted pair
100BASE-TX connectors and two (2)
sets of RX (receive) and TX (transmit)

SC 100BASE-FX connectors to 1300
nm singlemode fiber-optic cable.

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE
PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in
damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-Mitgliedstaaten
verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie 91/263/EWG zur
Angleichung der Rechtsvorschriften der Mitgliedstaaten über Telekommunikationsendeinrichtungen
einschliesslich der gegenseitigen Anerkennung ihrer Konformität.

C/E-R-TX-FX-01 in the Network . . . . . .2

Installation . . . . . . . . . . . . . . . . . . . .3

Operation . . . . . . . . . . . . . . . . . . . . .4

Fault Isolation and Correction . . . . .5

Cable Specifications . . . . . . . . . . . . .6

Technical Specifications . . . . . . . . . .7

Compliance Information . . . . . . . . . .8

Media
Conversion
Center

Power Modules

Power

1

In Use

Power

2

In Use

Management
Module

Power

Link

TX

RX

C/E-R-TX-FX-01 IN THE NETWORK

Recessed switches located on each side of the media converter are used to
configure the media converter for the network.

NOTE: Switch labels are located

AT TOP of C/E-R-TX-FX-01 media converter.

MDI/MDI-X SWITCHES

(One for each RJ-45 port - located one on each side of media
converter) Allows straight-through twisted-pair cable to be
used for crossover 100BASE-TX connections.

4-POSITION SWITCH (3rd switch not used)

Auto-negotiation (UP) Detects and adapts to line speed and

operating mode of attached device.
Full/Half-duplex (UP) Allows an attached full-duplex station to

transmit and receive simultaneously. (DOWN) Allows an
attached station to transmit and receive sequentially.

Port Select Timer (UP) Selects timer duration of eleven (11) seconds.
(DOWN) Selects timer duration of five (5) seconds.

TECHNICAL SPECIFICATIONS

Standards IEEE 802.3
Case Dimensions 5.7" x 3.0" x 1.8" (145mm x 76mm x 46mm)
Shipping Weight 3 pounds (1.4 kilograms)
Delay 400nsec round trip
Environment Temperature: 0-50°C (32° to 122° F )

Humidity 10-90%, non condensing
Altitude 0-10,000 feet

Power Supply Requirements Replace power supply with only the equivalent
input rating (see below) and output rating (unregulated 9-24VDC, 5.5W).

TN PN Requirement Location

3507 240 volts, 50 hertz United Kingdom
3342 230 volts, 50 hertz Europe
3340 120 volts, 60 hertz USA/Canada/Mexico
3346 100 volts, 50-60 hertz Japan
3511 240 volts, 50 hertz Australia
3537 (with power cord: 3522) South Africa

Warranty Lifetime

NOTE: Media Converter Slide-in-Modules can be installed in any
installation slot, in any order.

DECLARATION OF CONFORMITY

Name of Mfg: Transition Networks

6475 City West Parkway, Minneapolis MN 55344 USA

Model: Redundant Fast Ethernet

™

Media Converters

Part Number: C/E-R-TX-FX-01
Regulation: EMC Directive 89/336/EEC

Purpose: To declare that the C/E-R-TX-FX-01 to which this declaration refers is

in conformity with the following standards.

EMC-CISPR 22: 1985 Class A; EN 55022: 1988 Class A; EN 50082-1:1992;
EN 60950 A4:1997; IEC 801.2, IEC 801.3, and IEC 801.4; IEC 950

I, the undersigned, hereby declare that the equipment specified above conforms to the

above Directive(s) and Standard(s).

_May 1, 1999_____

Stephen Anderson, Vice-President of Engineering Date

Do NOT connect media
converters between hubs.
Install no more than two (2)
media converters in series.

SWITCH

100 meters

MDI switch setting
PST (UP) switch setting

2 kilometers - multimode
20 kilometers - singlemode

100 meters

MDI switch setting
PST (DOWN) switch setting

SWITCH