MiLAN MIL-S2612, MIL-S2614, MIL-S2613, MIL-S2615, MIL-S2622 User Manual
...
User’s Manual
MIL-S2612, 2-port 100BASE-FX Module (ST)
MIL-S2613, 2-port 100BASE-FX Module (SC)
MIL-S2614, 2-port 100BASE-FX Module (MT-RJ)
MIL-S2615, 2-port 100BASE-FX Module (VF-45)
MIL-S2622, 4-port 100BASE-FX Module (ST)
MIL-S2623, 4-port 100BASE-FX Module (SC)
MIL-S2624, 4-port 100BASE-FX Module (MT-RJ)
MIL-S2625, 4-port 100BASE-FX Module (VF-45)
MIL-S3630, 8-port 10/100BASE-TX Module (RJ-45)
MIL-S6603SX, 1-port 1000BASE-SX Module (SC)
MIL-S6603LX, 1-port 1000BASE-LX Module (SC)
1. 8 ports 10/100Base-TX Module
1
100
LK/ACT
FD/COL
MIL-S3630
2345678
Figure 1. Front Panel
When installed into a Switch hub, the 10/100Base-TX Module provides 8
10/100Mbps Switch ports which can connect to 10Mbps or 100Mbps hub or end
station.
1-1. 8 Ports 10/100Base-Tx Module Features
! 8 10/100Base-TX N-Way Switch ports.
! Conforms to IEEE 802.3, IEEE 802.3u and IEEE 802.3x standards
! Store and forward switch architecture for abnormal packet filtering
! Support for half and full duplex on all ports
! Backplane up to 2.4Gbps
! 2M memory Buffer support
! Automatic address learning with 12K address entry storage
! Filtering and forwarding rate of 14,880~148,800 packets per second
! DIP Switch for decision connection mode with other network devices
1-2. DIP Switch with Link Mode
The 8 port 10/100Base-TX module provides dip switch for 1 to 4 port to adjust link
mode with other network devices. Another 4 ports use auto-negotiation protocol
only. There are three type of link mode can be chosen, Auto-negotiation,
100Mbps/Full duplex and 10Mbps/Full duplex.
P o rt 1
P o rt 2
P o rt 3
P o rt 4
DIP Sw itc h fo r
P o rt 1 to P o rt 4
adjustable
ports
Autonegotiation
Full D uplex
100M
P o rt 5
P o rt 6
P o rt 7
P o rt 8
87654321
10M
ON
Port 1
Port 2 Port 4
Port 3
OFF
2
1
Figure 2. Dip switch location and mode settings
If you adjust to auto-negotiation, then the DIP for 100Mbps and 10Mbps is not
effective. If you adjust to Full duplex, then the DIP for 100Mbps and 10Mbps is
effective.
The following Table 1. lists the ports’ operating modes based on the DIP switch
position.
PORT 1 PORT 2 PORT3 PORT4
SW123 4 5678
ON Full 10M Full 10M Full 10M Full 10M
OFF Auto 100M Auto 100M Auto 100M Auto 100M
Table 1. 8 Ports 10/100Base-TX Module DIP switch functions
1-3. LED Descriptions
There are three LED indicators for each of the RJ-45 LAN connection ports. If
there is no connection to a port, the corresponding LED indicators are not lit.
•
100Mps
This LED indicator is green when the corresponding port is
connected to a 100Mbps device. This LED indicator is not lit when the
corresponding port is connected to a 10Mbps device.
•
Link/Activity
. This LED indicator is green when there is a connection secured
to a device (a link) to the corresponding port. The LED indicator blinks when
there is a transmission of data (activity) taking place at the corresponding port.
•
Duplex Mode/Collision
. This LED indicator is orange when the
corresponding port is operating in Full Duplex mode. When the corresponding
port is operating in Half Duplex, the LED indicator is not lit. When collisions
are occurring at the corresponding port, the LED indicator blinks.
2. Two ports 100Base-FX Fiber Module
12
TX TXRX RX
LK/ACT
FD/COL
MIL-S2612
Figure 3. 2 port 100Base-FX Module Front View
When installed into a Switch hub, this Module provides a 100Mbps Fast Ethernet
fiber port which can be used to:
" Connect the Switch to the backbone of your network; that is, to a basement
switch, hub or router
" Connect the Switch to a 100Mbps server or end-station
2-1. Two ports 100Base-FX Fiber Module Features
! Conforms to IEEE 802.3u Fast Ethernet standard
! Support for SC, ST, MT-RJ, VF-45 fiber connectors (optional)
! Supports half and full duplex modes via DIP switches
! Store-and-forward switch architecture for abnormal packet filtering
! 2 switching 100Mbps Fiber Ethernet ports
Loading...