R11e-4G
R11e-4G
is a standard Mini PCIe module, supports TDD-LTE/FDD-LTE network and provides
high speed and reliable mobile broadband data connection. LTE data rate can achieve DL 150 Mbps/UL
50 Mbps.
The rich interfaces and RF bands allow it to be widely used in CPE, industrial routers, security
monitoring, industrial equipment and other applications.
General Features
•LTE(FDD): B3/B7/B20/B31
•LTE(TDD): B41/B42/B43
•Environmental
℃
～
Operating Temperature: -10
Extreme working temperature: -10
Humidity: 5% ～ 95%
•Power Supply: 3.2 V to 4.2V (typical: 3.3V)
•Dimensions: 50.95mm * 30mm * 4.4mm
•AT Command: 3GPP TS 27.007 and 27.005
℃
60
℃ ～
+60 ℃
Interfaces
• Mini PCIe interface
• USB 2.0 x1
• SIM Card x1
• I2C Interface x1
• SPI Interface x1
• PCM Interface x1
• LED x4
• Reset x1
• Antenna interface x2
•OS: Windows/Linux/Android
RF Parameters
•Output Power
FDD LTE: 22dBm±2.26dB (3GPP TS 36.101 R9 Class 3)
TDD-LTE: 22dBm±0.6dB (3GPP TS 36.101 R9 Class 3)
•Sensitivity
FDD LTE:-93 dBm(20MHZ) @ 2 antenna
TDD LTE:-94 dBm(20MHZ) @ 2 antenna
Data Features
• LTE FDD : Category 4, DL 150Mbps UL 50Mbps
• LTE TDD: Category 4, DL 112Mbps UL 10Mbps
Additional Features
Certifications
• FCC*(North Americal)
• CE*(Europe)
Application
• LTE CPE
• Industrial Routers
• Security Monitoring
• Firmware update via USB
• FOTA
Important Notice to OEM integrators
1. This module is limited to OEM installation ONLY.
2. This module is limited to installation in mobile or fixed applications, according to Part
2.1091(b).
3. The separate approval is required for all other operating configurations, including
portable configurations with respect to Part 2.1093 and different antenna configurations
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module in the user's manual of the end product which
integrates this module. The end user manual shall include all required regulatory
information/warning as show in this manual.
CAN ICES-3(B)/NMB-3(B)
Innovation, Science and Economic Development Canada
This device complies with Industry Canada's licence-exempt RSSs. Operation is subject
to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
(1) Le présent appareil est conforme aux CNR d'lndustrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes:
(2) I'appareil ne doit pas produire de brouillage, et
I'utilisateur de I'appareil doit accepter tout brouillage radioélectrique subi ，même si le
brouillage est susceptible d'en compromettre le fonctionnement."
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
For class B digital device
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable
protection against harmful interference in a residential installation. This equipment
generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment. This transmitter
must not be
co-Iocated or operating in conjunction with any other antenna or transmitter.
Radiation Exposure Statement
This equipment complies with FCC/IC RF exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20
cm between the radiator & your body.
Déclaration d'exposition aux radiations
Cet équipement est conforme aux limites d'exposition RF FCC / IC définies pour un
environnement non contrôlé Cet équipement doit être installé et utilisé avec une distance
minimale de 20 cm entre le radiateur et votre corps.
End Product Labeling
The host system using this module must display a visible label indicating the following
text: Contains FCC ID: TV7R11E4G
The host system using this module must display a visible label indicating the following
text: Contains IC:7442A-R11E4G
This device is intended only for OEM integrators under the following conditions:
The antenna must be installed such that 20 cm is maintained between the antenna and
users,
The transmitter module may not be co-Iocated with any other transmitter or antenna
In the event that these conditions cannot be met (for example certain laptop
configurations or co-Iocation with another transmitter), then the FCC/IC authorization is
no longer considered valid and the FCC/IC ID cannot be used on the final product. In
these circumstances, the OEM
integrator will be responsible for re-evaluating the end product (including the transmitter)
and obtaining a separate FCC/IC authorization
Loading...