MikroTik CSS610-1Gi-7R-2S+OUT User Manual
1.
2.
3.
4.
netPower Lite 7R
netPower Lite 7R(CSS610-1Gi-7R-2S+OUT)
Safety Warnings
Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing
accidents.
Read the installation instructions before connecting the system to the power source.
This equipment is to be installed by trained and qualified personnel, as per these installation instructions. The installer is responsible for obtaining any
required local or national safety inspections of the structural integrity of the installation by the local authority/inspection department.
All installation methods for mounting an access point on any wall surface is subject to the acceptance of local jurisdiction.
The Installation of the equipment must comply with local and national electrical codes.
This unit is intended to be mounted outdoors on a pole. Please read the mounting instructions carefully before beginning installation. Failure to use the
correct hardware and configuration or to follow the correct procedures could result in a hazardous situation to people and damage to the system.
We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your
own risk.
Quickstart
Please follow these quick steps to set up your device:
Download the latest SwitchOS software version fromhttps://mikrotik.com/download;
Connect your computer to any of the ethernet ports;
Connect the device to the power source;
Set an IP address of your computer to the 192.168.88.3;
Open your Web browser, the default management IP address is , with the username and no password;192.168.88.1 / 192.168.88.2
admin
Upload file with the web browser to the Upgrade tab, the device will reboot after an upgrade;
Set up your password to secure the device.
Expansion slots and ports
Gigabit Ethernet, one port PoE-out.
Gigabit Ethernet, eight ports.
Gigabit Ethernet, seven ports, Reverse PoE (PoE in).
Two - 10G SFP+ ports.
Configuration
The device can be discovered using Winbox utility, by clicking on the Neighbors list. The default management address is 192.168.88.1.
SwOS is a simple software designed for the switch. We suggest starting here to get yourself accustomed to the possibilities: .https://mt.lv/help
For recovery purposes, it is possible to boot the device for reinstallation, see section .netPower Lite 7R#Buttons and Jumpers
1.
2.
3.
1.
2.
3.
Powering
The device accepts power in the two ways following ways:
Direct-input power jack, (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts 12-57 V DC.
Direct-input block terminal, 12-57 V DC .
PoE in,12-57 V DC .
The power consumption under maximum load can reach 7 W, with attachments 29 W.
Power output
The device supports passive PoE from Ethernet port eight. You can power Mikrotik devices which supports powering through Ethernet. The power
delivered through the PoE port will depend on the incoming to the device.
Connecting to a PoE Adapter, only to deliver power to other devices:
Connect the Ethernet cable from the device to the PoE+DATA port of the PoE adapter.
Connect an Ethernet cable from your local network (LAN) to the PoE adapter.
Connect the power cord to the adapter, and then plug the power cord into a power outlet.
Bottom Lid
The bottom lid is secured in place with the captive screw, it can be unscrewed by hand, but do not remove the screw completely.
Pull the cover towards.
Lift to access Ethernet ports.
Mounting
The device can be mounted in several ways: pole, wall, or ceiling. The package also includes a drill hole template with detailed mounting instructions, to
help you with the drill hole marking. The device has eight mounting points for versatility use zip ties or steel clamps for mounting on the pole.
The IP rating scale for this device is IP54. When mounting outdoors, please ensure that any cable openings are directed downwards. We recommend
using the POE injector and proper grounding with Cat6 shielded cable.
Mounting points:
There are eight mounting points on the back of this device. Choose the most relevant ones.
Middle points are designed for mounting on the mast, there are curves on the case for slim fitment.
It's recommended to secure Ethernet cable to the pole using zip ties. With the distance from the device approximately 30 cm.
The installation infrastructure (towers and masts), as well as the router itself, must be properly grounded. The device includes a grounding wire attachment
screw on the backside.
Attach your grounding wire to the grounding screw.
Attach the other end of the grounding wire to the grounded mast.
The device must be mounted by UP arrow facing upwards.
Loading...