MikroTik CRS318-16P-2S+OUT User manual

1.

2.

3.

4.

5.

6.

7.

8.

9.

netPower 16P

netPower 16P (CRS318-16P-2S+OUT)

The netPower is a weatherproof switch with the capability of delivering PoE to your connected devices.

Quickstart

Please follow these quick steps to set up your device:

Open the bottom lid (see " ");netPower 16P#Bottom Lid
Connect all served devices to Ethernet ports;
Connect the device to the power source (see " ");netPower 16P#Powering

Once connected to the same network, open in your web browser to start configuration, user name: a and there is no http://192.168.88.1

dmin

password by default;
Once connected configure the device, so it has an active Internet connection ;https://mt.lv/configuration
Upgrade the RouterOS software to the latest version ;https://mt.lv/upgrade
Set up your router password in the bottom field of the QuickSet menu, to the right and repeat it, it will be used to login next time.

Expansion slots and ports

DC power connector 48 – 57 V.
DC power connector 18 – 30 V.
LED indicating a power state of the device.
Reset button.
Gigabit Ethernet, 8 - ports, delivering PoE out.
Gigabit Ethernet, 8 - ports, delivering PoE out.
Two - 10G SFP+ ports.
LED Indicating the activity of SFP port.
LED Indicating the speed of SFP port.

Configuration

1.

2.

3.

1.

2.

3.

1.

The device can be discovered using Winbox utility, by clicking on the Neighbors list. The default management address is 192.168.88.1. To reach both
devices needs to be in the same IP network. Configured as a bridge, ARP, and fast forward enabled. RSTP protocol activated.
RouterOS includes many configuration options in addition to what is described in this document. We suggest starting here to get yourself accustomed to
the possibilities: .http://mt.lv/help
For recovery purposes, it is possible to boot the device for reinstallation, see section .netPower 16P#Buttons and Jumpers

Powering

The device accepts power in the two ways following ways:

Direct-input power jack 1, (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts 18-30 V DC.
Direct-input power jack 2, 48-57 V DC .

Use included DC plug to connect with your power source:

DC plug 2.1x5.5x12 mm to Screw Terminal 2pin.
Connect your power source cables to the two pins and secure them in place by tightening screws.
Connect DC plug to the device.

The power consumption under maximum load can reach 21 W, with attachments 325 W.

Power output

The device supports 802.3af/at PoE from Ethernet 1 - 16. You can power Mikrotik devices which supports powering through Ethernet. The power delivered
through the PoE port will depend on the incoming to the device.

Max out per port when input greater than 30 V - 1.1 A.
Max out per port when input lower than 30 V – 0.6 A.
Max total out 2.8 A.

Connecting to a PoE Adapter, only to deliver power to other devices:

Connect the Ethernet cable from the device to the PoE+DATA port of the PoE adapter.
Connect an Ethernet cable from your local network (LAN) to the PoE adapter.
Connect the power cord to the adapter, and then plug the power cord into a power outlet.

Bottom Lid

Bottom lid is secured in place with the captive screw, it can be unscrewed by hand, but do not remove the screw completely.

When using both the high and low Voltage adapters, the netPower will automatically choose the correct PoE standard and Voltage, based on
the devices you connect to each port. This can also be specified manually.

2.

3.

Pull the cover towards.

Lift to access Ethernet ports.

Mounting

The device can be mounted in several ways: pole, wall, or ceiling. The package also includes a drill hole template with detailed mounting instructions, to
help you with the drill hole marking. The device has eight mounting points for versatility use zip ties or steel clamps for mounting on the pole.

The IP rating scale for this device is IP54. When mounting outdoors, please ensure that any cable openings are directed downwards.