Miki Pulley ETP BUSH, ETP-CLASSIC, ETP-A, ETP-A-B, ETP-A-C Instruction Manual

TRS-ETA-005-01 /MD-000074158A

Shaft

Clamping bolt

Hub

Piston ring

Sleeve

Flange

Sealing ring

Pressure medium

P1
P2
P4
P8

ETP BUSH

ETP-CLASSIC

ETP-A/ETP-A-B/ETP-A-C

ETP-A-S/ETP-A-R

Instruction Manual

Before use this product, read the instruction manual carefully and use the product safety and correctly.

１．Before using・・・・・・・・・・・・・・・
２．Safety Precautions・・・・・・・・・・・・
３．Installation procedure ・・・・・・・・・・
４．Removal ・・・・・・・・・・・・・・・・・

1.Before using

1-1 After opening the package

First, please check the following points.

1) Is the product what you ordered?

2) Is the product damaged during transportation?

If any problems are found, please contact your supplier.

1-2 Structure and Parts

-1-

DANGER

When death or serious injury may result
by mishandling

CAUTION

When disability or only physical damage
may result by mishandling

Structural precautions

Touching the product during operation could cause injury. Place a safety
cover to avoid any accident. Additionally, set up a safety mechanism for
quick stop of the product when opening the cover.

Do not use the product near flammable liquids or in the presence of gas
and other explosive air particles.

The driven and driving sides could be completely detached when the
product is damaged. Set up a safety mechanism such as a safety brake to
avoid any danger.

Mounting precautions

Depending on the tightening adjustment of bolt or screw, exceptionally
dangerous situations such as product damage or performance degradation
could occur. Always use a calibrated torque wrench and clamp at the
tightening torque specified by Miki Pulley.

It is very dangerous if the driving part starts by accident while mounting
the product. Be sure that the main power of the equipment is turned off.

Cautions during operation

If the product is used in excess of more than its maximum rated
permissible speed, very dangerous product damage could occur by a large
vibration.

Due to the exposed rotor, touching the product during operation may
cause injury. Make sure not to touch the product during operation.

Using the product with more than the "maximum permissible
misalignment" could cause damage or adverse effect on the equipment.
Always operate the product within the specified "maximum permissible

DANGER

2.Safety Precautions

Please read carefully through the instruction manual and the technical information for proper

use and safety. In this manual, safety precautions are classified by "DANGER" and "CAUTION".

Equipment use (atomic energy, aerospace, medical treatment, transportation, or various
safety devices) that may result in serious bodily injury or loss of life directly by mechanical
failure or mishandling, careful examination is necessary. Contact us for further information. The
company has taken all possible measures to produce a quality product; however, continuous
rotational states when the clutch can not be disengaged or coasting of the machine when the
brakes went off is envisioned as emergency. Please pay attention to safety measures in case
anything goes wrong.

-2-

misalignment."

Cautions for maintenance and inspection

It is extremely dangerous if the driving part starts operating by accident
while dismounting the product. Make sure that the main power of the
equipment is off.

Cautions for disposal

Do not leave the product around where young children may play.

Structural precautions

Do not use the product in an environment where chemicals may spill,
humidity is high, or in hot or cold temperature.

Mounting precautions

The installation of the product must be performed within the specified
maximum permissible error. Using the product with more than the
maximum permissible error could cause damage or adverse effect on the
equipment.

Using a bolt or screw that is not specified by our company could damage
the product. Do not use any bolt or screw unspecified.

To avoid any injury by stripping, spring pin or keyway, make sure to wear

protective equipment such as safety glasses or gloves.

Lifting of a heavy weight could cause back injury. Use a hoist when

carrying or mounting the product.
Cautions during operation

Using the product with more than the specified permissible torque could
cause damage or adverse effect on the equipment.

If abnormal noises or vibrations occur during operation, improper
mounting should be considered. Do not leave the situation as it is. It may
cause damage to the equipment itself. Also, for reasons other than above,
the belts and other screws may loosen or become defective even if the
product is mounted correctly.

Using the product when the locking part is in a slip condition could over
heat the product, which could cause damage to the equipment.

Cautions for maintenance and inspection

We will refuse to take responsibility as to the damaged product that is
dismantled, remodeled or repaired by a third party except our company and
the designated company. Therefore, for the product that the assembly
process or procedure of dismantlement is described in the manual, we will
not be responsible as well. Please use our service network for repair and
dismantlement.

Cautions for disposal

Call for a waste-control-collection company for disposal.

CAUTION

-3-