Mikado Logo 690 SX User Manual
www.mikado-heli.de
© Mikado Model Helicopters GmbH 2014, V1.0001
LOGO 690 SX
Manual
Mikado Model Helicopters GmbH • Friedrich-Klausing-Straße 2 • 14469 Potsdam • Germany
phone +49 (0)331 23749-0 • fax +49 (0)331 23749-11 • www.mikado-heli.de
Manual LOGO 690SX - ©Mikado Model Helicopters GmbH - Page 2
Index
OPERATING YOUR MODEL SAFELY
Operate the helicopter in spacious areas with no
people nearby.
!Warning: Do NOT operate the helicopter in the following places and situations (or else you risk severe
accidents):
• in places where children gather or people pass
through
• in residential areas and parks
• indoors and in limited space
• in windy weather or when there is any rain, snow,
fog or other precipitation
If you do not observe these instructions you may be
held reliable for personal injury or property damage!
Always check the R/C system prior to operating your
helicopter. When the R/C system batteries get weaker,
the operational range of the R/C system decreases.
Note that you may lose control of your model when
operating it under such conditions.
Keep in mind that other people around you might also
be operating a R/C model.
Never use a frequency which someone else is using
at the same time. Radio signals will be mixed and you
will lose control of your model.
If the model shows irregular behavior, bring the model
to a halt immediately. Turn off all power switches and
disconnect the batteries. Investigate the reason and
x the problem. Do not operate the model again as
long as the problem is not solved, as this may lead to
further trouble and unforeseen accidents.
! Warning: In order to prevent accidents and personal
injury, be sure to observe the following:
Before ying the helicopter, ensure that all screws are
tightened. A single loose screw may cause a major
accident.
Replace all broken or defective parts with new ones,
as damaged parts lead to crashes.
Never approach a spinning rotor. Keep at least 10 meters/yards away from a spinning rotor blades.
Do not touch the motor immediately after use. It may
be hot enough to cause burns.
Perform all necessary maintenance.
PRIOR TO ADJUSTING AND OPERATING YOUR MODEL, OBSERVE THE FOLLOWING
!Warning: Operate the helicopter only outdoors and
out of people’s reach as the main rotor operates at
high rpm!
! Warning: While adjusting, stand at least 10 meters/
yards away from the helicopter!
Novice R/C helicopter pilots should always seek advice
from experienced pilots to obtain hints with assem-
bly and for pre-ight adjustments. Note that a badly
assembled or insufciently adjusted helicopter is a
safety hazard!
In the beginning, novice R/C helicopter pilots should
always be assisted by an experienced pilot and never
y alone!
Tools for Assembly & R/C Equipment
Radio with Heli-Software
Motor + Speed Controller (check the Mika-
do webpages for recommended motors)
Alle shown products are examples. You may use different brands.
Scissors
Rubber Hammer
Screwdrivers
(plus and minus)
Hex Wrenches
1.5/2.0/2.5/3.0/4.0 mm
(.055/.079/.098/.118 in)
Ball
link
pliers
Threadlock
circlips
pliers
Grease
Pitch Gauge
Safety Instructions
Safety Instructions . . . . . . . . . . . . . . . . . 2
Tools for Assembly & R/C Equipment . . . . . . . 2
1 Mainframe . . . . . . . . . . . . . . . . . . . . . 3
2 Tail Rotor . . . . . . . . . . . . . . . . . . . . . 4
3 Tail Boom . . . . . . . . . . . . . . . . . . . . . 5
4 Main Gear & Tail Boom Assembly . . . . . . . . 6
5 V-Bar Rotor Head . . . . . . . . . . . . . . . . . 7
6 Servo Installation . . . . . . . . . . . . . . . . . 8
7 Mounting the Motor . . . . . . . . . . . . . . . . 9
8 Canopy Mounting . . . . . . . . . . . . . . . . . 9
9 Radio and Battery . . . . . . . . . . . . . . . 10
10 Overview Chassis . . . . . . . . . . . . . . . 11
11 Overview Tail Rotor . . . . . . . . . . . . . . 12
12 Overview V-Bar Head . . . . . . . . . . . . . 13
V-Bar
Manual Mikado LOGO 690 SX
Note: There is no bag 10. The bags are numbered 1 to 12, with the exception of 10.
Max. rotorhead rpm LOGO SX 690: 2000
Max. collective range: +/- 11°
Max. rotor blade size: 690 mm
Max. tail rotor blade size: 105mm
Max. LiPo Akku siz e: 10S 5000 mAh
Max. LiPo Akku siz e: 12S 5000 mAh
LOGO 690 SX is not recommended for novices. This helicopter is a complex system. Basic knowledge of the function of a model helicopter is required to build and operate
the LOGO 690 SX.
5
Minute
Epoxy
5
Minute
Epoxy
Warning:
The LOGO 690 SX is designed to be used with Scorpion motor HK 4525-370 Kv and a 15 teeth pinion exclusively. Do not use any other motors of any kind, as this can cause damage or failure of the gear train. It is
absolutely essential to keep within the recommended pitch range from +/- 11°. Otherwise the one way bearing
will be damaged.
Manual LOGO 690SX - ©Mikado Model Helicopters GmbH - Page 3
14x M2,5
3x
SW5x59
2x 3x17
4x
3x5x2,5
10x M2,5x10
4x M3x10
4x
M2,5x16
4x
M2,5x12
31
10x19x5
M2,5x16 (4x)
3x7x3
3x17
M2,5x12
M2,5x12
M3x10
M3x10
Using the rod M2.5x60 from bag 7, position all
14 nylon nuts in the right side frame.
Before you combine the two sides of the main
frame, attach the two belt tensioners (#4089,
bag 6).
1 Mainframe
Bag 1
Bag 1
All parts shown in the boxes are displayed in real size.
You should position the motor pinion
on the motor shaft, before you mount
the motor plate. You may also mount
the motor pinion at a later stage, but
the process will be more cumbersome. For reading on how to mount
the motor pinion, please ip to page 9.
Manual LOGO 690SX - ©Mikado Model Helicopters GmbH - Page 4
Beutel 5
M3x14
M2x8
3x6x2,5
3x5x0,5
3x5x5
M3 Stopp
(5x)
M2,5x6
3
M3x16
5x8x3
6x8x0,5
M3 Stopp
1x
3x5x5
1x M2x8
1x
Kugel/ball/Rotule Ø4,8x2
1x 3x5x0,5
1x M3x14
2x 3x6x2,5
1
1
a
b
c
d
3
3x8
5x13x4
3x5x27
M3x35 (5x)
M3x8
5x8x3,7
27mm
3x5x0,5
3x5x10
3x7x3
2x 6x8x0,5
2x M3x8
4x 5x8x3
2x
M3x16
2x 4x8x3,5
2x M3
1x M3x3
1
5x M3
1x M2,5x6
1x 3x5x27
2x
M3x8
5x
M3x35
M3 Stop
(5x)
2x 3x5x10
2x
3x7x3
2x 5x13x4
1x
2x
5x8x3,7
3x5x0,5
2 Tail Rotor
Apply grease
on bearing
larger
inner Ø
smaller
inner Ø
Apply Loctite only in the
threaded section inside the
tail rotor hub!
Glue ball bearings
using 5min. Epoxy
Bag 5
Bag 5
Bag 5
Bag 5
Loading...