MII 66158-101, 66158-011, 66158-001 Datasheet
SINGLE CHANNEL OPTOCOUPLER
66158
DIRECT REPLACEMENT FOR 3C92C
REVISION B
12/29/00
Features:
Applications:
• High Reliability
Base lead eliminated for improved noise immunity
•
Rugged package
•
Stability over wide temperature
•
+500V electrical isolation
•
Eliminate ground loops
•
• Level shifting
Line receiver
•
Switching power supplies
•
Motor control
•
DESCRIPTION
Mii
OPTOELECTRONIC PRODUCTS
DIVISION
The
contains a gallium arsenide infrared LED optically coupled to a silicon planar phototransistor. The optocoupler
66158
is built on a TO-46 header. The collector of the phototransistor is electrically connected to the case. This optocoupler is
capable of transmitting signals between two galvanic sources. The potential difference between transmitter and receiver
should not go over the maximum isolation voltage. The internal base connection has been eliminated for improved noise
immunity.
ABSOLUTE MAXIMUM RATINGS
Input to Output Voltage....................................................................................................................................................... 500V
Emitter-Collector Voltage........................................................................................................................................................ 7V
Collector-Emitter Voltage (value applies to emitter-base open-circuited & the input-diode equal to zero) ........................ 60V
Reverse Input Voltage ........................................................................................................................................................... 7V
Input Diode Continuous Forward Current at (or below) 65°C Free-Air Temperature (see note 1) ................................. 50mA
Peak Forward Input Current (value applies for tw
s, PRR < 300 pps) .....................................................................500mA
< 1µ
Continuous Collector Current ............................................................................................................................................ 50mA
Continuous Transistor Power Dissipation at (or below) 25°C Free-Air Temperature (see Note 2) ..............................230mW
Storage Temperature........................................................................................................................................-65°C to +150°C
Operating Free-Air Temperature Range ..........................................................................................................-55°C to +125°C
Lead Solder Temperature (10 seconds max.) ................................................................................................................ 260°C
Notes:
1. Derate linearly to 125°C free-air temperature at the rate of 0.67 mA/°C above 65°C.
2. Derate linearly to 125°C free-air temperature at the rate of 2.3 mW/
C.
°
Package Dimensions Schematic Diagram
4 LEADS
0.019Ø (0.48)
0.016Ø (0.41)
0.230Ø (5.84)
0.209Ø (5.31)
0.195Ø (4.95)
0.178Ø (4.52)
0.030 (0.76) MAX
0.210 [5.34]
0.170 [4.32]
DIMENSIONS ARE IN INCHES (MILLIMETERS)
MICROPAC INDUSTRIES, INC. OPTOELECTRONIC PRODUCTS DIVISION • 725 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 487-6918
0.50 [12.70] MIN
www.micropac.com
COLLECTOR
EMMITTER
CATHODE
E-MAIL:
Ø0.100[2.54]
3
2
1
0.046 [1.17]
0.036 [0.91]
ANODE
4
0.048 [1.22]
45°
0.028 [0.71]
optosales@micropac.com
3 - 46
66158
REVISION B 12/29/00
ELECTRICAL CHARACTERISTICS
TA = 25°C unless otherwise specified.
PARAMETER SYMBOL MIN TYP MAX UNITS TEST CONDITIONS
Input Diode Static Reverse Current I
SINGLE CHANNEL OPTOCOUPLER
R
1µA V
(Direct Replacement for 3C92C)
= 3V
R
Input Diode Static Forward Voltage V
Input Diode Static Forward Voltage V
Reverse Breakdown Voltage B
Input Diode Capacitance C
F
F
VR
IN
OUTPUT TRANSISTOR
TA = 25°C unless otherwise specified.
PARAMETER SYMBOL MIN TYP MAX UNITS TEST CONDITIONS
Collector-Emitter Breakdown Voltage V
Emitter-Collector Breakdown Voltage V
Collector-Emitter Dark Current I
(BR)CEO
(BR)ECO
CEO1
I
CEO2
COUPLED CHARACTERISTICS
TA = 25°C unless otherwise specified.
PARAMETER SYMBOL MIN TYP MAX UNITS TEST CONDITIONS
On State Collector Current I
On State Collector Current I
On State Collector Current -55°CI
Collector-Emitter Saturation Voltage V
Isolation Resistance R
C(ON)
C(ON)
C(ON)
CE(SAT)
ISO
1.15 1.2 V IF = 2mA
1.3 1.5 V IF = 50mA
712 V I
= 100µA
R
25 pF V = 0V, f = 1MHz
50 V IC = 1mA, I
7VI
50
10
nA
nA
4mAV
320mAV
2mAV
= 10µA, I
C
VCE = 50V, IF = 0mA
V
CE
CE
CE
CE
= 0, IF = 0
B
= 10µA, IF = 0
E
= 5V, IF = 0mA
= 5V, IF = 10mA
= 0.4V, IF = 10mA
= 5V, IF = 10mA
0.4 V IF = 50mA, IC = 10mA
9
10
Ω
V
IN-OUT
= 500V
Input to Output Capacitance C
Delay Time t
Storage Time t
Rise Time t
Fall Time t
IO
d
s
r
f
2 2.5 pF f = 1MHz
24µsV
0.2 0.5
sV
µ
35µsV
45µsV
= 5V, IF = 2mA, RL = 100
CE
= 5V, IF = 2mA, RL = 100
CE
= 5V, IF = 2mA, RL = 100
CE
= 5V, IF = 2mA, RL = 100
CE
RECOMMENDED OPERATING CONDITIONS:
PARAMETER SYMBOL MIN MAX UNITS
Input Current, Low Level I
Input Current, High Level I
Supply Voltage V
Operating Temperature T
FL
FH
CE
A
01µA
210mA
550 V
-55 125
SELECTION GUIDE
PART NUMBER PART DESCRIPTION
66158-011
66158-101
66158-001
MICROPAC INDUSTRIES, INC. OPTOELECTRONIC PRODUCTS DIVISION • 725 E. Walnut St., Garland, TX 75040 • (972) 272-3571 • Fax (972) 487-6918
Single Channel optocoupler, military operating range (-55° to +125°C)
Single Channel optocoupler, full mil-temp (-55° to +125°C) with 100% device screening
Single Channel optocoupler, commercial (0
www.micropac.com
E-MAIL:
optosales@micropac.com
° to 70°
C)
Ω
Ω
Ω
Ω
C
°
3 - 47
Loading...