MII 66056-103, 66056-102, 66056-101, 66056-012, 66056-011 Datasheet
...
SINGLE/DUAL CHANNEL, HERMETICALLY SEALED,
66056
VERY HIGH SPEED OPTOCOUPLER
Rev 1 7/3/01
Features:
• DSCC Approved 8102802PX (Dual); and
single channel version optocoupler
10 MHz bandwidth typical
•
1500 Vdc isolation test voltage
•
TTL compatible input and output
•
High radiation immunity
•
Faraday shield to provide high common mode
•
rejection
DESCRIPTION
Applications:
Military and space
•
• Voltage level shifting
Isolated receiver input
•
Communication systems
•
Medical systems
•
Mii
OPTOELECTRONIC PRODUCTS
DIVISION
The
single and dual channel optocouplers consist of LED’s optically coupled to two high speed, high gain inverting
66056
detector gates. Maximum isolation can be achieved while providing TTL outputs capable of switching with propagation delays
of 55ns typical. The 66056 is available in military temperature range and military temperature with 100% device screening.
The devices are built in eight-pin dual-in-line, hermetically sealed packages and provide high input to output DC isolation.
ABSOLUTE MAXIMUM RATINGS
Storage Temperature ............................................................................................................................................ -65°C to +150°C
Operating Free-Air Temperature Range ............................................................................................................... -55°C to +125°C
Lead Solder Temperature ..........................................................................................260°C for 10s (1.6mm below seating plane)
Peak Forward Input Current (each channel) .................................................................................................40mA (1ms duration)
Average Forward Input Current (each channel)…(see Note 1) ............................................................................................ 20mA
Input Power Dissipation (each channel) ............................................................................................................................... 35mW
Reverse Input Voltage (each channel) ........................................................................................................................................5V
.................................................................................................................................. 7V(1 minute maximum)
Supply voltage - V
Output Current - I
CC
(each channel) ........................................................................................................................................ 25mA
O
Output Power Dissipation (each channel) ............................................................................................................................ 40mW
Output Voltage - V
(each channel) ............................................................................................................................................7V
O
Total Power Dissipation (per channels) .............................................................................................................................. 175mW
NOTES:
1. Derate IF at 0.05mA/°C above 25°C.
Package Dimensions Schematic Diagrams
Single Channel
Vcc
GND
GND
8
Vo
6
5
Vcc
8
Vo1
7
Vo2
6
5
PIN ONE
0.370 [9.040]
0.390 [9.90]
6875
YYWW
USA
XXXX
2431
TYPE NUMB ER
DATE CODE
0.007 [0.18]
0.013 [0.33]
SIDE VIEWREAR VIEW
0.280 [7.11]
0.310 [7.88]
0.090 [2.28]
0.110 [2.80]
0.320 [8.13]MAX
NOTE:
AL L DIM EN SIO NS A RE IN IN CH ES [MIL LIM ET ER S]
PIN ONE
END VIEW
0.170 [4.32]MAX
0.02 0 [0.51 ] M IN
.02 0 [0.51 ] MA X
NOTE:
A .0 1 to .1 u F byp ass
capacitor must be placed
between Vcc and Gnd
2
3
2
1
6
5
A
K
Dual Channel
A
K
A
K
MICROPAC INDUSTRIES, INC. OPTOELECTRONIC PRODUCTS DIVISION • 725 E. Walnut St.., Garland, TX 75040 • (972) 272-3571 • Fax (972) 487-6918
www.micropac.com
E-MAIL: optosales@micropac.com
3 - 34
66056
SINGLE/DUAL CHANNEL, HERMETICALLY SEALED, VERY HIGH SPEED OPTOCOUPLER
Rev 1 7/3/01
ELECTRICAL CHARACTERISTICS T
=-55°C to at 125°C unless otherwise specified.
a
PARAMETER SYMBOL MIN TYP MAX UNITS TEST CONDITIONS NOTE
High Level Output Current I
Low Level Output Voltage V
High Level Supply Current Single Channel
I
CCH
Dual Channel
Low Level Supply Current Single Channel
I
CCL
Dual Channel
Input Forward Voltage V
Input Reverse Breakdown Voltage BV
Input-Output Insulation Leakage Current I
I—O
Propagation Delay Time To High Output Level t
Propagation Delay Time To Low Output Level t
TYPICAL CHARACTERISTICS
TA = 25°C, VCC = 5V EACH CHANNEL
OH
OL
PLH
PHL
5250 µAV
0.5 0.6 V VCC = 5.5V, IF = 10mA
9
14
18
13
26
F
R
1.5 1.75 V IF = 20mA 1
5VI
28
18
36
mA V
mA VCC = 5.5V, IF = 20mA
1.0 µA V
45 100 ns R
55 100 ns RL = 510Ω, C
= 5.5V, VO = 5.5V,I
CC
I
(Sinking) = 10mA
OL
= 5.5V, IF = 0
CC
(Both Channels)
(Both Channels)
R
= 1500Vdc,
I—0
Relative Humidity = 45%
ta = 25°C, t = 5s
= 510Ω, CL = 50pF.
L
If = 13mA, t
If = 13mA, ta = 25°C
PARAMETER SYMBOL MIN TYP MAX UNITS TEST CONDITIONS NOTE
Input Capacitance C
Input Diode Temperature Coefficient
Resistance (Input-Output) R
Capacitance (Input-Output) C
Output Rise-Fall Time (10-90%) t
Common Mode Transient Immunity at
IN
∆
∆
v
T
F
A
I-0
I-O
t
,
r
f
CM
H
1000 10000 V/µsV
High Output Level
Common Mode Transient Immunity at
CM
L
1000 10000 V/µsV
Low Output Level
NOTES:
1. Each channel
2. Measured between input pins shorted together and output pins shorted together.
3. It is essential that a bypass capacitor (.01 to 0.1µF ceramic) be connected from pin 1 to pin 4.
4. The t
5. The t
propagation delay is measured from the 6.5mA point on the trailing edge of the input pulse to the 1.5V point on the trailing edge of the output pulse.
plh
propagation delay is measured from the 6.5mA point on the leading edge of the input pulse to the 1.5V point on the leading edge of the output pulse.
phl
6. CMh is the max. tolerable common mode transient to assure that the output will remain in a high logic state (i.e. V
7. CMl is the max. tolerable common mode transient to assure that the output will remain in a low logic state (i.e. Vo < 0.8V).
60 pF VF = 0, f = MHz 1
-1.9 mV/°CI
10
12
Ω
= 20mA 1
F
V
I—O
5 pF f = 1MHz 2
35 ns RL = 510Ω, C
= 50pFI
L
= 10V (peak),
CM
V
(min) = 2V,
O
RL = 510Ω, IF = OmA
= 10V (peak),
CM
V
(max) = 0.8V,
O
RL = 510Ω, IF = 1OmA
>
2.0V).
o
=250µA 1
F
= 10µA
= 25°C
a
= 50pF
L
= 500V 2
= 13mA
F
1,3
2
3,4
3,5
6
7
RECOMMENDED OPERATING CONDITIONS:
PARAMETER SYMBOL MIN MAX UNITS
Input Current, Low Level Each Channel I
Input Current, High Level Each Channel I
Supply Voltage V
FL
FH
C
0250µA
12.5 20 mA
4.5 5.5 V
Fan Out (TTL Load) Each Channel N 6
Operating Temperature T
A
-55 125
°
C
SELECTION GUIDE
PART NUMBER PART DESCRIPTION
66056-011 Single Channel, commercial optocoupler
66056-012 Dual Channel, commercial optocoupler
66056-001
66056-002
Single Channel, Mil-temp optocoupler tested over full military temperature range (-55° to +125°C)
Dual Channel, Mil-temp optocoupler tested over full military temperature range (-55° to +125°C)
66056-101 Single Channel optocoupler tested over full military temperature range with 100% device screening
66056-102 Dual Channel optocoupler tested over full military temperature range with 100% device screening
66056-103 DSCC Dwg 8102802PX Dual channel optocoupler
MICROPAC INDUSTRIES, INC. OPTOELECTRONIC PRODUCTS DIVISION • 725 E. Walnut St.., Garland, TX 75040 • (972) 272-3571 • Fax (972) 487-6918
www.micropac.com
E-MAIL: optosales@micropac.com
3 - 35
Loading...