Pre-finished
30” MasterCool
K 2801 SF / K 2811 SF
F 2801 SF / F 2811 SF
KF 2801 SF / KF 2811 SF
Shown: F 2471 SF merged with K 2801 SF
Please note: This information is subject to change
Specification Sheets TRS 05202019
8mieleusa.com
Pre-finished
30” MasterCool
SPECIFICATIONS
Overall Unit Dimensions 29
Overall Fascia Dimensions 30
Niche
Minimum Cabinet Niche Opening 30” (762 mm) W* x 84” - 85
Electrical
Electrical Requirements
Power Cord NEMA 5-15 plug, 5 ft (1.52 m)
Plumbing K 28x1 SF F 28x1 SF KF 28x1 SF
Water Supply Requirements -
3
/4” (756 mm) W x 833/4”- 853/16” (2127 - 2164 mm) H x 24” (610 mm) D [Excludes Fascia Dimension]
1
/2” (775 mm) W x 84”- 8511/16” (2134 - 2175 mm) H x 11/2” (32 mm) D
3
/16” (2134 - 2164 mm) H x 24” (610 mm) D
K 28x1 SF F 28x1 SF KF 28x1 SF
110V / 120V, 60Hz, 15 Amps
In the case of side-by-side installations, a separate outlet must be used for each appliance.
Connect to a cold water supply only. Do not connect to a low-mineral or
a reverse osmosis system. Must be connected to a shut-off valve. The
water shut-off valve must be accessible after installation. The water pressure must be between 29 psi (2 bar) and 116 psi (8 bar). If the pressure is
higher than 120 psi (8.3 bar), a pressure reducing valve must be installed.
Water Connection Line
Shipping
-
K 28x1 SF F 28x1 SF KF 28x1 SF
Standard 1/4” O.D flexible water line. The maximum outer diameter of the
water pipe (without fittings): 3/8” (10 mm). Water line is not included.
Shipping Weight 453 lbs (205.5 kg) 462 lbs (210 kg) 485 lbs (220 kg)
Shipping Dimensions 29
7
/8” (759 mm) W x 841/4” (1,240 mm) H x 297/8” (759 mm) D
Support
Call Miele (800) 999-1360
Miele Website
20/20 Link
8www.mieleusa.com
82020technologies.com
Please note the following:
• This specication sheet is for a single built-in unit.
• When combining multiple MasterCool units side-by-side, please refer to the Merging Kit specication sheet.
*If design calls for a partition less than 6
5
/16” (160 mm) the left unit’s cutout will require an additional 1/8” (3 mm) to the width to allow installation of
the Heating Mat/Merge Kit.
K 2801 SF (Right Hinged)
Item 36280111USA
K 2811 SF (Left Hinged)
Item 36281111USA
F 2801 SF (Right Hinged)
Item 37280111USA
F 2811 SF (Left Hinged)
Item 37281111USA
KF 2801 SF (Right Hinged)
Item 38280111USA
KF 2811 SF (Left Hinged)
Item 38281111USA
Page 2 of 6
CUTOUT DIMENSIONS
Please note unit’s outer SF frame.
Top view:
Niche/Cabinetry
3/4”
(19)
9/32”
(7)
Pre-finished
30” MasterCool
Stainless steel door
SF frame
CUTOUT DETAILS
• The electrical connection must not be positioned higher
than 9” (228.6 mm) above the oor.
• The 1/4” (6.4 mm) plumbed water connection should
not be positioned higher than 2” (50.8 mm) above the
oor.
Notes:
In case of an emergency the electrical outlet must be
easily accessible and must not be concealed behind the
appliance.
Page 3 of 6
Pre-finished
30” MasterCool
POWER SUPPLY AND WATER CONNECTION
(Water Connection For F 28x1 SF & KF 28x1 SF Only)
Rear View Front View
Electrical - 5 foot (1.52 m) - 120 Volt - 15 Amp
- NEMA 5-15 molded plug
Water line - 1/4” exible water line - not included
Side View
Water connection is located in front of unit.
1/4” compression tting is needed.
Electrical
Connection
Page 4 of 6
HINGING DETAILS 115° OPENING
0-3/4"
1"
1-1/4"
1-1/2"
0-1/8"
F
ro
nt
Pa
n
el
0-3/4"
1-1/4"
1-1/2"
1-3/4"
1"
Cabinet Front
rooD °511rooD °09
snoitpo ssenkcihTsnoitpo ssenkcihT
0-3/4"
1"
1-1/4"
1-1/2"
0-1/8"
F
ro
nt
Pa
n
el
0-3/4"
1-1/4"
1-1/2"
1-3/4"
1"
Cabinet Front
rooD °511rooD °09
snoitpo ssenkcihTsnoitpo ssenkcihT
Door Swing
Available for the following models:
• K 28x1 SF
• F 28x1 SF
• KF 28x1 SF
1-1/4” (32 mm)
1-1/2” (38 mm)
1-3/4” (44 mm)
0-3/4” (19 mm)
1” (25 mm)
30” MasterCool
0-3/4” (19 mm)
Pre-finished
1/4”(6.4mm)
1/4”(6.4mm)
2-5/8”
(67mm)
2-5/8”
(67mm)
2-1/3” (59mm)
2-1/3” (59mm)
2-1/24”(52mm)
2-1/24”(52mm)
1-3/8”(35mm)
1-3/8”(35mm)
1-1/6”
1-1/6”
17/24” (18mm)
17/24” (18mm)
(29.6mm)
(29.6mm)
1-3/4”(44.5mm)
1-3/4”(44.5mm)
3”(76.2mm)
3”(76.2mm)
0-1/8” (3 mm)
DOOR SWING AT 115° OPENING
1-1/2” (38 mm)
1” (25 mm)
1-1/4” (32 mm)
11 3/4”
16 7/8"
(298 mm)
MAX
Max
NOTE: Additional space needed depending on
thickness of front panels and handle used
Page 5 of 6
HINGING DETAILS 90° OPENING
0-1/8"
Front Panel
1"
1-1/4"
1-1/2"
0-3/4"
0-3/4"
1-1/4"
1-1/2"
1-3/4"
2"
1"
Cabinet Front
0-3/4"
1"
1-1/4"
1-1/2"
F
ro
nt
Pa
n
el
0-3/4"
1-1/4"
1-1/2"
1-3/4"
1"
Cabinet Front
snoitpo ssenkcihTsnoitpo ssenkcihT
0-3/4"
1"
1-1/4"
1-1/2"
0-1/8"
F
ro
nt
Pa
n
el
0-3/4"
1-1/4"
1-1/2"
1-3/4"
1"
Cabinet Front
rooD °511rooD °09
snoitpo ssenkcihTsnoitpo ssenkcihT
Door Swing
14 3/8"
MAX
NOTE: Additional space needed depending on the thickness
of front panels and handle used.
Freezer units cannot be stop pinned at 90°
0-1/8"
Front Panel
1"
1-1/4"
1-1/2"
0-3/4"
0-3/4"
1-1/4"
1-1/2"
1-3/4"
2"
1"
Cabinet Front
0-3/4"
1"
1-1/4"
1-1/2"
0-1/8"
F
ro
nt
Pa
n
el
0-3/4"
1-1/4"
1-1/2"
1-3/4"
1"
Cabinet Front
rooD °511rooD °09
snoitpo ssenkcihTsnoitpo ssenkcihT
Door Swing
Door Swing
16 7/8"
MAX
NOTE: Additional space needed depending on
thickness of front panels and handle used
Available for the following models:
• K 28x1 SF
• KF 28x1 SF
2” (51 mm)
1-1/4” (32 mm)
1-3/4” (44 mm)
1-1/2” (38 mm)
0-3/4” (19 mm)
1” (25 mm)
Pre-finished
30” MasterCool
7/16”
(11 mm)
1-3/16”
(30mm)
1-7/16”
(36.5mm)
1-11/16”
(43mm)
1-15/16”
(49.2mm)
0-1/8” (3 mm)
DOOR SWING AT 90° OPENING
Handle or object that is
NOT ush with Cabinet
Front.
0-3/4” (19 mm)
1” (25 mm)
1-1/4” (32 mm)
1-1/2” (38 mm)
7/16” (11 mm)
7/16"
38 11/16"
/16” (830 mm)
11
32
When installing hinge side next to an appliance or object that is within range of the door panel,
limit the door opening angle to 90°. This is done by installing the banking pin as illustrated.
Insert the banking pin through the holes and drive in with a hammer.
NOTE: Additional space needed depending on
thickness of front panels and handle used
Specification Sheets TRS 05202019
Page 6 of 6
Loading...