Miele KD 12823 S User Manual

Page 1
Operating and installation instructions
Fridge freezer KD 12823 S
To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time.
en-GB
Page 2
Contents
Guide to the appliance .............................................4
Caring for the environment..........................................6
Warning and Safety instructions .....................................7
How to save energy ...............................................12
Switching on and off ..............................................13
Switching off for longer periods of time .................................13
The correct temperature ...........................................14
. . . temperature in the refrigerator section ..............................14
...inthefreezer section ............................................14
Setting the temperature .............................................14
Temperature display ...............................................14
Super freeze .....................................................15
Super freeze .....................................................15
Using the refrigerator efficiently ....................................16
Different storage zones .............................................16
Food which should not be stored in a refrigerator.........................16
When shopping for food ............................................17
Storing food correctly ..............................................17
Fruit and vegetables .............................................17
Unpacked meats and vegetables ..................................18
Protein rich foods ...............................................18
Meat .........................................................18
Adjusting the interior fittings .......................................19
Moving the shelves ................................................19
Split shelf ........................................................19
Adjusting the door shelf/bottle shelf ...................................19
Moving the bottle divider ............................................19
Freezing and storing food..........................................20
Maximum freezing capacity..........................................20
Freezing fresh food ................................................20
Storing frozen food ................................................20
Home freezing ....................................................21
Hints on home freezing...........................................21
Packing .......................................................21
Before placing food in the freezer ..................................22
Placing food in the freezer ........................................22
Freezing large items ...............................................22
Page 3
Contents
Defrosting .......................................................22
Ice cubes ........................................................23
Cooling drinks ....................................................23
Freezer tray ......................................................23
Cool pack........................................................24
Defrosting the appliance ...........................................25
Refrigerator section ................................................25
Freezer section ...................................................25
Cleaning and care ................................................27
Cleaning the outer casing, the interior and accessories ....................27
Ventilation gaps ...................................................27
Door seals .......................................................28
Problem solving guide ............................................29
Noises .........................................................32
After Sales / Guarantee ............................................33
Electrical connection..............................................34
Electrical connection U.K. ...........................................34
Installation ......................................................35
Location .........................................................35
Climate range ..................................................36
Ventilation .......................................................36
Installation .......................................................36
Aligning the appliance..............................................36
Appliance dimensions ..............................................37
Changing the door hinging .........................................38
Aligning the appliance doors .......................................44
Building in the appliance ..........................................45
Page 4
Guide to the appliance
a On/Off button
b Temperature selector button
c Refrigerator section temperature
display
d Super freeze button and
indicator light
4
Page 5
a Butter and cheese compartment
b Adjustable shelves
c Egg tray
d Door shelf
e Condensate channel and
drain hole
f Fruit and vegetable containers
g Bottle divider*
h Bottle shelf
i Freezer drawers
Guide to the appliance
* Depending on model
5
Page 6
Caring for the environment
Disposal of the packing material
The transport and protective packing has been selected from materials which are environmentally friendly for disposal, and can normally be recycled.
Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children. Danger of suffocation!
Rather than just throwing these materials away, please ensure that they are recycled.
Disposal of your old appliance
Electrical and electronic appliances often contain materials which, if handled or disposed of incorrectly, could be potentially hazardous to human health and to the environment. They are, however, essential for the correct functioning of your appliance. Please do not therefore dispose of it with your household waste.
Please dispose of it at your local community waste collection / recycling centre or contact your dealer for advice. Ensure that it presents no danger to children while being stored for disposal.
Take care not to damage the pipework at the back of it before or during transportation to an authorised collection depot. In this way, refrigerant in the pipework and oil in the compressor will be contained, and will not leak out into the environment.
6
Page 7
Warning and Safety instructions
This appliance complies with all relevant local and national safety requirements. Improper use can, however, present a risk of both personal injury and material damage.
To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using it for the first time. They contain important notes on the installation, safety, operation and care of the appliance.
Keep these instructions in a safe place and pass them on to any future user.
Correct application
This appliance is not designed for
~
commercial use. It is intended for use in domestic households and in similar working and residential environments such as:
This appliance is not intended for
~
use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they are supervised whilst using it, or have been shown how to use it correctly by a person responsible for their safety.
Safety with children
This appliance is not a toy! To avoid
~
the risk of injury, do not allow children to play with it or near it, or to play with the controls. Neither should they be allowed to swing on the door. Please supervise young children whilst you are using it. Older children may only use the appliance when its operation has been clearly explained to them and they are able to use it safely, recognising the dangers of misuse.
Shops
Offices and showrooms
Hostels and guest houses.
It must only be used as a domestic appliance to cool and store foodstuffs as well as to store deep frozen food, freeze fresh food and to prepare ice.
Any other usage is not supported by the manufacturer and could be dangerous. Miele cannot be held liable for damage resulting from incorrect or improper use or operation of the appliance.
7
Page 8
Warning and Safety instructions
Technical safety
Before setting up the appliance,
~
check it for any externally visible damage. Do not install and use a damaged appliance. A damaged appliance is dangerous.
If the connection cable is faulty it must
~
only be replaced by a service technician authorised by the manufacturer to protect the user from danger.
This appliance contains the coolant
~
Isobutane (R600a), a natural gas which is environmentally friendly. Although it is flammable, it does not damage the ozone layer and does not increase the greenhouse effect. The use of this coolant has, however, led to a slight increase in the noise level of the appliance. In addition to the noise of the compressor, you might be able to hear the coolant flowing around the system. This is unavoidable, but does not have any adverse effect on the performance of the appliance. Care must be taken during the transportation and installation of the appliance that no parts of the cooling system are damaged. Leaking coolant can damage the eyes. In the event of any damage:
- avoid open flames and anything
which creates a spark,
- disconnect from the mains,
- air the room in which the appliance
is located for several minutes and
- contact the Service Department for
advice.
room, there is the danger of combustible gases building up. For every8gofcoolant at least 1 m room space is required. The amount of coolant in the appliance is stated on the data plate inside the appliance.
Safe operation of the appliance is
~
only assured if it has been installed and connected in accordance with these operating and installation instructions.
Before connecting the appliance,
~
make sure that the connection data on the data plate (voltage and connected load) match the mains electricity supply. This data must correspond in order to avoid the risk of damage to the appliance. Consult a qualified electrician if in any doubt.
Do not connect the appliance to the
~
mains electricity supply by a multi-socket unit or an extension lead. These do not guarantee the required safety of the appliance (e.g. danger of overheating).
3
of
The more coolant there is in an
~
appliance, the larger the room it should be installed in. In the event of a leakage, if the appliance is in a small
8
Page 9
Warning and Safety instructions
The electrical safety of this
~
appliance can only be guaranteed when continuity is complete between it and an effective earthing system which complies with current local and national safety regulations. It is most important that this basic safety requirement is present and tested regularly, and where there is any doubt, the household wiring system should be inspected by a qualified electrician. The manufacturer cannot be held liable for damage or injury caused by the lack of or inadequacy of an effective earthing system (e.g. electric shock).
Installation, maintenance and
~
repairs may only be carried out by a suitably qualified and competent person in strict accordance with current national and local safety regulations. Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work.
The appliance must be isolated from
~
the electricity supply during installation, maintenance and repair work. The appliance is only completely isolated from the electricity supply when:
it has been switched off at the socket
and the plug has been withdrawn, or
the fuse from the fused spur
connection unit has been withdrawn, or
the mains fuse has been
disconnected, or
– the screw-out fuse has been
removed (in countries where this is applicable).
Faulty components must only be
~
replaced by genuine Miele original spare parts. The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used.
While the appliance is under
~
guarantee, repairs should only be undertaken by a service technician authorised by the manufacturer. Otherwise the guarantee will be invalidated.
This appliance may only be used in
~
mobile installations such as ships, if a risk assessment of the installation has been carried out by a suitably qualified engineer.
In countries where there are areas
~
which may be subject to infestation by cockroaches or other vermin, pay particular attention to keeping the appliance and its surroundings in a clean condition at all times. Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee.
9
Page 10
Warning and Safety instructions
Correct use
Never handle frozen food with wet
~
hands. Your hands may freeze to the frozen food. Danger of frost burn.
Do not take ice cubes out with your
~
bare hands and never place ice cubes or ice lollies in your mouth straight from the freezer. The very low temperature of the frozen ice or lollies can cause frost burn to the lips and tongue.
Do not refreeze thawed or partially
~
thawed food. Defrosted food should be used up as quickly as possible, as food soon loses its nutritional value and goes off. Defrosted food may only be re-frozen after it has been cooked.
Do not store explosive materials in
~
the appliance or any products containing propellants (e.g. spray cans). Thermostats switching on may produce sparks which could present a fire hazard. Flammable compounds could explode.
Do not operate any electrical
~
equipment (e.g. an electric ice-cream maker) inside the appliance. Danger of sparking and explosion.
If storing alcohol with a high
~
percentage proof, make sure it is tightly closed and stored upright. Danger of explosion.
Do not store cans or bottles
~
containing carbonated drinks or liquids which could freeze in the freezer. The cans or bottles could explode. Danger of injury and damage to the appliance.
When cooling drinks quickly in the
~
freezer, make sure bottles are not left in for more than one hour; otherwise they could burst, resulting in injury or damage.
Observe the "use by" dates given on
~
food to avoid the risk of food poisoning. Storage times will depend on several factors, including the freshness and quality of the food as well as the temperature at which it is stored. Follow the instructions given on the food manufacturer's packaging regarding storage conditions and "use-by" dates.
Do not use sharp edged objects to
~
– remove frost and ice,
– separate frozen foods and remove
ice trays.
They will damage the evaporator, causing irreversible damage to the appliance.
Do not place electric heaters or
~
candles in the appliance to defrost it. These can damage the plastic parts.
10
Page 11
Warning and Safety instructions
Do not use defrosting sprays or
~
de-icers, as they might contain substances which could damage the plastic parts or which could cause the build-up of gases and pose a danger to health.
Do not use any oils or grease on the
~
door seals, as these will cause the seals to deteriorate and become porous with time.
Do not store cooking oil in the
~
refrigerator door. Traces of oil can cause stress cracks to occur in the plastic components in the door.
Do not block the ventilation gaps in
~
the appliance as this would impair the efficiency of the appliance, increase the electricity consumption and could cause damage to the appliance.
The appliance is designed for use
~
within certain climate ranges (ambient temperatures), and should not be used outside this range. The climate range for your appliance is stated on the data plate inside the appliance. Installing it in a room with too low an ambient temperature, e.g. a garage, can lead to the appliance switching off for longer periods so that it cannot maintain the required temperature.
Disposal of your old appliance
Before disposing of an old
~
appliance, first make the door latch or lock unusable. This way you will prevent children from accidentally locking themselves in and endangering their lives.
Be careful not to damage any part of
~
the pipework whilst awaiting disposal, e.g. by
puncturing the refrigerant channels
in the evaporator.
bending any pipework.
– scratching the surface coating.
Splashes of refrigerant can damage the eyes.
The manufacturer cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions.
Do not use a steam-cleaning
~
appliance to defrost or clean this appliance. Steam could reach the electrical components and cause a short circuit.
11
Page 12
How to save energy
Normal energy consumption
Installation site In a ventilated room. In an enclosed, unventilated room.
Protected from direct sunlight. In direct sunlight.
Not situated near to a heat source (radiator, oven).
Where the ideal ambient room temperature is approx. 20°C.
Temperature setting with a thermostat which is approximate (set in stages).
Temperature setting with a thermostat which is exact to the degree (digital display).
Use Only open the doors when
Defrosting Defrost the freezer compartment
With a medium setting of 2 to 3. With a high setting: the lower the
Cellar section 8 to 12°C
Refrigerator section 4 to 5 °C
PerfectFresh zone just above 0 °C
Freezer section -18°C
Wine storage section 10 to 12 °C
necessary and for as short a time as possible.
Store food in an organised way. If food is not stored in an
Allow hot food and drinks to cool down before placing them in the appliance.
Store food covered or packaged. The evaporation or condensation
Place frozen food in the refrigerator to defrost.
Do not over-fill the appliance to allow air to circulate.
when a layer of ice 0.5 cm thick has built up.
Increased energy consumption
Situated near to a heat source (radiator, oven).
Where there is a high ambient room temperature.
temperature in the compartment, the higher the energy consumption.
On appliances with winter setting, please make sure that the winter setting is switched off when the ambient temperature is warmer than 16 °C.
Frequent opening of the doors for long periods will cause a loss of coldness.
organised way, searching for an item will mean the door is open for longer.
Placing hot food in the appliance will cause the compressor to run for a long time, as the appliance will have to work harder to lower the temperature.
of liquids will cause a loss of coldness in the refrigerator.
A layer of ice hinders the cold from reaching the frozen food, and causes an increase in energy consumption.
12
Page 13
Switching on and off
Before using for the first time
The stainless steel trim to the interior shelves and the door shelves has a layer of protective foil to prevent scratching during transportation.
Clean the inside of the appliance and
^
the accessories with lukewarm water and a little washing-up liquid, and then dry with a soft cloth.
Carefully remove the protective foil
^
from the stainless steel trim.
Important: To ensure the correct functioning of the appliance, let it stand for between 1½ and 2 hours after transporting it to its final location before connecting it to the mains.
Switching on
Switching off
Press the On/Off button until the
^
temperature display goes out.
The interior light will not come on when you open the door and the cooling process will be switched off.
Switching off for longer periods of time
If the appliance is not going to be used for a longer period of time, e.g. whilst on holiday:
^ switch the appliance off, ^ switch off at the wall socket and
withdraw the plug,
^ defrost the appliance, ^ clean the appliance out and
^
Press the On/Off button. The temperature display will light up.
The temperature display for the refrigerator section will show the required temperature setting.
The appliance will start cooling down and the interior light in the refrigerator section will come on if you open the door.
Allow the appliance to run for a few hours before placing food in it. This will ensure that the temperature is sufficiently low.
^
leave the doors ajar to air it.
If, during a long absence, the appliance is switched off but not cleaned out and the doors are left shut, there is a danger of mould and odours building up inside the appliance.
13
Page 14
The correct temperature
It is very important to set the correct temperature for storing food in the appliance. Micro-organisms will cause food which is not stored at the correct temperature to deteriorate rapidly. Temperature influences the growth rate of these micro-organisms. Reducing the temperature reduces their growth rate.
The temperature in the appliance will rise:
the more often the door is opened
and the longer it is kept open,
– the more food that is stored in it,
– the warmer the food is which is being
put into it,
– the higher the ambient temperature
surrounding the appliance. The appliance is designed for use in specific ambient temperatures (climate ranges). Do not use in ambient temperatures for which it is not designed.
. . . temperature in the refrigerator section
We recommend a temperature of 5°C in the middle of the refrigerator.
...inthefreezer section
or defrosted food must not be re-frozen. Food may be re-frozen once it has been cooked, as the high temperatures achieved when cooking destroy most micro-organisms.
Setting the temperature
The temperatures for the refrigerator and the freezer sections are set with the temperature selector button.
^ Press the temperature button
repeatedly until the indicator light for the temperature you want lights up in the temperature display for the refrigerator section.
The temperature will be adjusted continuously with each press of the button.
When the refrigerator section is set to 5°C, the freezer section will have an average temperature of -18 °C.
Temperature display
The temperature display on the control panel always shows the required temperature.
To freeze fresh food and to store frozen food for a long time, a temperature of
-18 °C is required. At this temperature the growth of micro-organisms is generally halted. As soon as the temperature rises above -10 °C, the micro-organisms become active in the food again so that it cannot be kept as long. For this reason, partially defrosted
14
The temperature can be adjusted from: 1°Cto9°C
Page 15
Super freeze
Super freeze
Switch the Super freeze function on before putting fresh food into the freezer.
This helps food to freeze quickly and retain its nutrients, vitamins, flavours and appearance.
Super freeze is not necessary:
when putting in food that is already
frozen.
when freezing less than 2 kg fresh
food daily.
Switching on Super freeze
When freezing small quantities of food in the freezer, the Super freeze function should be switched on 6 hours
beforehand. When freezing the maximum load of food the Super
freeze function should be switched on
24 hours beforehand.
Switching off Super freeze
The Super freeze function will switch off automatically after approx. 65 hours. The indicator light will go out and the appliance will run at normal power again.
To save energy, the Super freeze function can be switched off once a constant temperature of -18°C or colder has been reached in the freezer. You should also check the temperature inside the appliance from time to time.
Press the Super freeze button. The
^
Super freeze indicator light will go out, and the appliance will continue to operate at normal power.
^
Press the Super freeze button. The Super freeze indicator light will come on.
The appliance works at full power to lower the temperature in the appliance.
15
Page 16
Using the refrigerator efficiently
Different storage zones
Due to the natural circulation of the air in the appliance, there are different temperature zones in the refrigerator. Cold, heavy air sinks to the lowest section of the appliance. Make use of the different zones when placing food in the appliance.
Do not store explosive materials in the appliance or any products containing propellants (e.g. spray cans). Danger of explosion.
If storing alcohol with a high percentage proof, make sure it is tightly closed, and store upright.
Warmest area
The warmest area is in the top section of the door. Use this for storing butter and cheese.
Coldest area
The coldest area in a refrigerator is directly above the vegetable containers.
Use this for all delicate and highly perishable food, e.g.
– fish, meat, poultry,
– sausage products, ready meals,
dishes or baked goods containing eggs or cream,
fresh dough, cake mixtures, pizza or quiche dough,
soft cheese and other dairy products,
pre-packed vegetables and other fresh food with a label stating it should be kept at a temperature of approx. 4 °C.
Do not store cooking oil in the refrigerator door. Traces of oil can cause stress cracks to occur in the plastic components in the door.
Food must not touch the back wall of the appliance, as it may freeze to the back wall.
Food which should not be stored in a refrigerator
Not all food is suitable for refrigeration. This includes:
Fruit and vegetables which are sensitive to cold, such as bananas, avocado, papaya, passion fruit, aubergines, peppers, tomatoes and cucumbers
Fruit which is not yet ripe
Potatoes
Some hard cheeses, e.g. Parmesan
16
Page 17
Using the refrigerator efficiently
When shopping for food
The freshness of food when first placed in the appliance is an important factor in determining how long it stays fresh. Time out of the refrigerator e.g. during transportation should be kept to a minimum. For example, do not allow food to stay in a hot car for too long. Once food has started to deteriorate, this process cannot be reversed. As little as two hours outside the refrigerator can cause food to start deteriorating.
Storing food correctly
Store food covered or packaged. This will prevent food smells from affecting other foods, food from drying out, and also any cross-contamination of bacteria. The growth of bacteria, such as salmonella, can be avoided by setting the correct temperature and maintaining good standards of hygiene.
Fruit and vegetables
Fruit and vegetables may be stored loose in the vegetable containers. However, you should bear in mind that aromas and flavours can transfer from one type of food to another (e.g. carrots absorb the smell and flavour of onions very easily). Some food also gives off a natural gas (ethylene) which speeds up the rate at which other food perishes. Some fruit and vegetables react strongly to this gas and should not be stored together.
Examples of fruit and vegetables
which produce a large amount of this natural gas are:
Apples, apricots, pears, nectarines, peaches, plums, avocado, figs, blueberries, melons and beans.
– Examples of fruit and vegetables
which react strongly to the natural gases given off by other types of fruit and vegetables are:
Kiwis, broccoli, cauliflower, Brussels sprouts, mangos, honeydew melons, apples, apricots, cucumbers, tomatoes, pears, nectarines and peaches.
Example: Broccoli should not be stored with apples, as apples produce a large amount of natural gas to which broccoli is very sensitive. The result is a shorter than expected storage time for the broccoli.
17
Page 18
Using the refrigerator efficiently
Unpacked meats and vegetables
Unpackaged meat and vegetables should be stored separately. To avoid any microbiological cross-contamination, these foods may only be stored together if they are wrapped.
Protein rich foods
Please note that foods rich in protein deteriorate faster than others. Shellfish, for example, deteriorates faster than fish, and fish deteriorates faster than meat.
Meat
Meat should be stored unwrapped. (Undo wrappings slightly to leave meat loosely covered, and leave containers open). This permits air to circulate around the meat, allowing the surface to dry slightly, which helps prevent the growth of bacteria. To prevent the risk of bacterial cross-contamination, do not let meat come into direct contact with other foods.
18
Page 19
Moving the shelves
The shelves can be adjusted according to the height of the food.
Raise the shelf, and pull it forwards
^
slightly until the notch at the side is in line with the shelf support. It can then be raised or lowered to the required level.
The raised edge at the back must face upwards to prevent food from touching the back of the appliance and freezing to it.
Stoppers prevent the shelves from being dislodged by mistake.
Adjusting the interior fittings
fit the two brackets onto the supports
^
on either side at the required height,
and push the glass shelves in one
^
after the other. The shelf with the raised edge must be at the back.
Split shelf
In order to accommodate tall items in the appliance, one of the shelves is divided. The front section can be pushed under the rear section.
^ Push the rear half of the glass shelf
up slightly from below.
^
At the same time, pull the front half of the glass shelf forwards slightly and then push it carefully under the rear half.
To move the split shelf:
^
Take both halves of the split glass shelf out,
Adjusting the door shelf/bottle shelf
^ Push the door/bottle shelf upwards,
then remove it by pulling it forwards.
^ Replace the door/bottle shelf at the
required position. Ensure that it is securely pushed back into position.
Moving the bottle divider
(depending on model)
The bottle divider can be moved to the left or right to ensure that bottles are held securely in position when the door is opened and shut.
The bottle divider can be removed completely (e.g. for cleaning).
^
To do this, push up the front edge of the bottle divider, and disengage it.
19
Page 20
Freezing and storing food
Maximum freezing capacity
To ensure that fresh food placed in the freezer freezes through to the core as quickly as possible, the maximum freezing capacity must not be exceeded. The maximum freezing capacity for freezing within a 24-hour period is given on the data plate:
"Freezing capacity ....kg/24 hrs".
The maximum freezing capacity given on the data plate has been calculated according to DIN EN ISO 15502 Stan dard.
-
Freezing fresh food
Fresh food should be frozen as quickly as possible. This way the nutritional value of the food, its vitamin content, appearance and taste are not impaired.
Food which takes a long time to freeze will lose more water from its cells, which then shrink. During the defrosting process, only some of this water is reabsorbed by the cells; the rest collects around the food.
Storing frozen food
When buying frozen food to store in your freezer compartment, check
that the packaging is not damaged,
the use-by date,
the temperature at which the frozen
food is being stored in the shop. The length of time it can be kept is reduced if it has been stored at a temperature warmer than -18 °C.
Buy frozen food once you have
^
finished the rest of your shopping, and wrap it in newspaper or use a cool bag or cool box to transport it.
^ Store it in the freezer as soon as
possible.
Never re-freeze partially or fully defrosted food. Consume defrosted food as soon as possible as it will lose its nutritional value and spoil if left for too long. Defrosted food may only be re-frozen after it has been cooked.
If food is frozen quickly, the cells have less time to lose moisture, so they shrink less. As there is not so much moisture loss, it is easier for the food to reabsorb it during the defrosting process, and very little water collects around the defrosted food.
20
Page 21
Freezing and storing food
Home freezing
Only freeze fresh food which is in a good condition.
Hints on home freezing
The following types of food are
suitable for freezing: Fresh meat, poultry, game, fish, vegetables, herbs, fresh fruit, dairy products, pastry, leftovers, egg yolks, egg whites and a range of pre-cooked meals.
The following types of food are not
suitable for freezing: Grapes, lettuce, radishes, sour cream, mayonnaise, eggs in their shells, onions, whole raw apples and pears.
– To retain colour, taste and vitamin C,
vegetables should be blanched after they have been trimmed and washed. To blanch: bring a large saucepan of water to the boil, immerse the vegetables in the fast boiling water for 2-3 minutes, depending on variety. Remove, and plunge into ice-cold water to cool quickly. Drain and pack ready for freezing.
Lean meat freezes better than fatty meat, and can be stored for considerably longer.
To prevent chops, steaks, cutlets or rolled meat from freezing together in solid blocks when packed, separate with a sheet of plastic freezer film.
lightly before freezing, but care should be taken as the taste of some spices alters when frozen.
Do not place hot foods or drinks in
the freezer. This causes already frozen food to thaw, and increases the energy consumption considerably. Allow hot foods and drinks to cool down before placing them in the freezer.
Packing
Freeze food in portions.
^
Unsuitable packing material
- wrapping paper
- grease-proof paper
- cellophane
- bin bags
- plastic carrier bags
Suitable packing material
- plastic freezer film
- freezer bags
- aluminium foil
- freezer containers
^
Expel as much air as possible from bags etc. before sealing them, to prevent freezer-burn on food.
^
Close the packaging tightly with
- rubber bands
- plastic clips
- string or bag ties
- freezer tape.
Freezer bags may also be sealed using home heat sealing kits.
Do not season fresh foods or blanched vegetables before freezing. Only season cooked food
^
Make a note of the contents and the date of freezing on the packaging.
21
Page 22
Freezing and storing food
Before placing food in the freezer
When freezing more than 2 kg of
^
fresh food, switch on the Super freeze function for some time before placing the food in the freezer (see "Super freeze").
When freezing, make sure that food already frozen does not come into contact with fresh food being frozen as this could cause the frozen food to begin to defrost.
This helps food that is already in the freezer section to stay frozen.
Placing food in the freezer
Food to be frozen can be placed anywhere in the freezer.
Large quantities should be placed directly on the glass cold plates to freeze the food quickly. To do this first take out the top two freezer drawers. When removing the top drawer, make sure that you do not block the ventilation slits in the back wall of the appliance. They are important for trouble-free operation of the appliance.
The lowest freezer drawer must always remain in the appliance.
Each drawer and glass cold plate can take a maximum of 25 kg.
^
Place the food flat in the bottom of the freezer drawers or on the glass cold plates so that it freezes through to the core as quickly as possible.
^
Make sure that the packaging and containers are dry to prevent them sticking together when frozen.
Freezing large items
If you wish to freeze large items such as a turkey or game, the glass cold plates between the drawers can also be removed. To do this:
Remove the top two freezer drawers,
^
and carefully lift and slide out the glass cold plates.
Defrosting
Frozen food can be defrosted in different ways:
– in a microwave oven,
– in an oven using the "Fan" or
"Defrost" setting,
at room temperature,
in the refrigerator (the cold given off by the frozen food helps to keep the other food cold),
in a steam oven.
Poultry It is particularly important to observe food hygiene rules when defrosting poultry. Do not use the liquid from defrosted poultry. Pour it away and wash the container it was in, the sink and your hands. Danger of salmonella poisoning.
22
Fruit should be defrosted at room temperature in its packaging, or in a covered bowl.
Page 23
Freezing and storing food
Most vegetables can be cooked while
still frozen. Just put straight into boiling water or hot fat. The cooking time is slightly less than that of fresh vegetables due to changes in the cell structure.
Never re-freeze partially or fully defrosted food. Consume defrosted food as soon as possible as it will lose its nutritional value and spoil if left for too long. Defrosted food may only be re-frozen after it has been cooked.
Ice cubes
^ Fill the ice tray three quarters full with
water, and place it in the bottom of one of the drawers.
Freezer tray
The freezer tray is useful for freezing small items such as berries, herbs and vegetables. They can be frozen individually and therefore maintain their shape when defrosted.
^ Space the food out loosely on the
tray.
^ Hang the tray in one of the upper
freezer drawers.
Leave the food for 10-12 hours to freeze thoroughly on the tray. Transfer it to a freezer bag or suitable container once frozen. Place the bag or container in the freezer drawer.
^
Once frozen, use a blunt instrument, for example a spoon handle, to remove the ice tray from the freezer.
^
Ice cubes can be removed easily from the tray by twisting the tray gently or by holding it under cold running water for a short while.
Cooling drinks
When placing bottles in the freezer section for rapid cooling, make sure
they are not left in for more than one hour as they could burst.
23
Page 24
Freezing and storing food
Cool pack
The cool pack prevents the temperature in the freezer rising too quickly in the event of a power cut.
Place the cool pack in the upper drawer directly on top of food, or in the freezer tray to save space. The cool pack will be at its most effective after it has been in the freezer for approx. 24 hours.
If there is a power cut, place the cool pack directly on top of the frozen food in the top drawer so that the food will be kept cold for as long as possible.
When placing fresh food in the freezer, use the cool pack to separate the fresh food from the food which is already frozen so that the frozen food does not begin to thaw.
The cool pack can also be used in a cool bag to keep food or drinks cool for a short period of time.
24
Page 25
Defrosting the appliance
Refrigerator section
The refrigerator defrosts automatically.
Condensate and frost can build up on the back wall of the refrigerator section whilst it is in use. You do not need to remove this, as it will defrost and evaporate automatically with the warmth generated by the refrigerator.
The condensate is drained away via a channel and drain hole into an evaporation system at the back of the appliance.
Ensure that the condensate channel and drain hole are kept clean and are never blocked so that condensate can flow away without hindrance.
Freezer section
The freezer section does not defrost automatically.
In normal use, ice and frost will form in the freezer. If allowed to accumulate, this will impair the efficiency of the freezer and increase the consumption of electricity.
Do not scrape ice and frost off as this can cause damage and render the appliance unusable.
The freezer section should be defrosted from time to time. It must be defrosted if a layer of ice approx. 0.5 cm thick has accumulated. It is best to defrost when only very little food or no food at all is left in the freezer.
Before defrosting
^ Switch on the Super freeze function
approx.1 day before defrosting to ensure frozen food retains its cold reserve for longer when taken out of the freezer.
^
Remove the frozen food from the freezer section and place it in another freezer or cool box, or wrap it in several layers of newspaper or cloths.
^
Store it in a cool place until the freezer section is ready for use again
^
Take all freezer drawers out of the freezer section.
25
Page 26
Defrosting the appliance
To defrost
Carry out the defrosting procedure as quickly as possible if food has not been placed in another freezer. The longer the food is left out at room temperature, the faster it defrosts.
Switch the appliance off using the
^
On/Off button, switch off at the socket and remove the plug.
Open the freezer section door.
^
To speed up defrosting, two bowls of hot water (not boiling) with plates underneath them can be placed in the appliance. Closing the door in this instance will help retain the warmth and speed up the defrosting process.
^ Use a sponge or towel to soak up the
defrosted water.
We do not recommend the use of hot air blowers such as hairdryers for defrosting your freezer.
After defrosting
Clean the freezer section and then
^
dry it thoroughly.
Close the freezer section door, plug
^
the appliance back into the mains socket and switch it on using the On/Off button.
Switch on the Super freeze function
^
so that the appliance can cool down quickly. The indicator light will come on.
Once the freezer section has
^
reached the required temperature, place the food back in the freezer drawers and slide the drawers back into the freezer section.
^ Switch off Super freeze by pressing
the Super freeze button when the temperature in the freezer is a constant -18 °C or colder. The indicator light will go out.
Never place electric heaters or candles in the appliance to defrost it. These can damage the plastic parts.
Do not use defrosting sprays or de-icers, as they could contain substances which may damage the plastic parts and which may cause a build-up of gases and pose a danger to health.
26
Page 27
Cleaning and care
A range of Miele branded cleaning
^
agents, including a microfibre "E-Cloth", is available from the Miele UK Spare Parts Department, or via the internet at www.miele-shop.com.
Never use cleaning agents containing abrasive substances such as sand, soda, acids chlorides or chemical solvents. "Non-abrasive" cleaning agents are also unsuitable as they can cause matt areas to appear.
Do not let water get into the electronic unit, into the light or into the ventilation gaps.
Do not let water get into the drainage channel and drain hole when cleaning.
Do not use steam cleaning apparatus to clean the appliance. Steam could reach the electrical components and cause a short circuit.
The data plate located inside the appliance must not be removed. It contains information which is required in the event of a service call.
Before cleaning
Switch the appliance off, switch off at
^
the wall socket and withdraw the plug.
Take any food out of the appliance
^
and store it in a cool place.
Defrost the freezer.
^
Take out any removable parts, e.g.
^
shelves, for cleaning.
Cleaning the outer casing, the interior and accessories
Use warm water with a little washing-up liquid. Wash all accessories and drawers by hand only. Do not wash in a dishwasher.
^ Clean the refrigerator section at least
once a month and the freezer section each time it is defrosted.
^ Clean the condensate channel and
drain hole frequently, so that condensate can drain away unhindered. Use a straw or similar to clear the drain if necessary.
^
After cleaning wipe the outer casing, interior and accessories with a damp cloth and dry with a soft cloth. Leave the doors open to air the appliance for a short while.
Ventilation gaps
^
The ventilation gaps should be cleaned on a regular basis with a brush or vacuum cleaner. A build up of dust will increase the appliance's energy consumption.
27
Page 28
Cleaning and care
Metal grille at the back of the appliance
The metal grille at the back of the appliance (heat exchanger) should be dusted at least once a year. A build-up of dust will increase the energy consumption of the appliance.
When cleaning the grille, make sure
^
that the pipework and other components do not get broken or damaged in any way.
Door seals
Do not use any oils or grease on the door seals. These will cause the seals to deteriorate and become porous over time.
The door seals should be cleaned regularly with clean water and then wiped dry with a soft cloth.
After cleaning
Replace all shelves and accessories
^
in the refrigerator section.
Place food back in the refrigerator
^
section, close the appliance doors, insert the plug in the socket and switch the appliance on.
Switch on the Super freeze function
^
so that the freezer section can cool down quickly.
Once the temperature in the freezer
^
has reached the required temperature, place the food back in the freezer.
^ Switch off Super freeze by pressing
the Super freeze button.
28
Page 29
Repairs to electrical appliances should only be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations. Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work.
What to do if...
. . . the appliance does not get cool.
^ Check whether the appliance has
been switched on. The temperature display must be lit up.
^ Check that the plug is correctly
inserted into the socket and switched on.
^ Check that the fuse is not defective
and that the mains fuse has not tripped. If it has, contact the Miele Service Department.
. . . the temperature in the refrigerator section or freezer section is too low.
^
Set a warmer temperature.
Problem solving guide
. . . the compressor is switching in too frequently and for too long.
Check whether the ventilation gaps
^
have been covered over or become dusty.
Check whether the metal grille (heat
^
exchanger) at the back of the appliance has become too dusty.
The doors have been opened too
^
frequently, or a large amount of fresh food has been put in at once for freezing.
Check that the doors have been
^
closed properly.
^ Check to see whether a thick layer of
ice has built up in the freezer. If it has, then the freezer section will need defrosting.
. . . part of the interior side wall feels warm?
This is not a fault. The appliance has an automatic temperature regulation system which maintains the optimum temperature inside both the refrigerator zone and the freezer zone.
^
The Super freeze function is still on and the Super freeze indicator light is on.
^
Check that the doors have been closed properly.
^
Has a large amount of fresh food been frozen at the same time? This makes the compressor run for longer, causing the temperature in the refrigerator section to fall automatically.
29
Page 30
Problem solving guide
. . . the frozen food is thawing because the freezer section is too warm.
Is the room temperature lower than
^
the ambient temperature for which the appliance is designed?
If so, raise the temperature of the room.
Operating in a room which is too cold will cause the cooling system to switch off for too long, causing the freezer section to become too warm.
. . . food has frozen together.
Use a blunt instrument, e.g. a spoon handle or plastic scraper, to prise it apart carefully.
......there is a thick layer of ice in
the freezer.
^ Check whether the freezer door
closes properly.
. . . the Super freeze indicator light and one of the temperature display lights are flashing at the same time.
There is a fault. Call the Service Department.
. . . the interior lighting in the refrigerator section is not working.
Was the refrigerator section door left
^
open for too long? The lighting switches itself off automatically after approx. 15 minutes if the door is left open.
If this is not the case, then the lamp is defective.
^ Disconnect the appliance from the
mains. Switch off at the wall and withdraw the plug from the socket, or disconnect the mains fuse or remove the screw-out fuse in countries where this is applicable.
^
Defrost and then clean the freezer section.
Too thick a layer of ice reduces efficiency and increases energy consumption.
. . . the door to the freezer section will not open because it has been opened and closed too many times in succession.
^
This is not a fault. The suction caused by opening and closing the door is preventing the door from opening. Wait a few minutes and then try again. It should now open without force.
30
^
Grip the lamp cover a at the front and unhook it at the back.
^
Unscrew the lamp b and replace it with a new one.
Page 31
Lamp specification: 220 - 240 V, E 14 fitting See the old lamp for the Wattage required.
Replace the lamp cover a .
^
. . . the floor of the refrigerator is wet.
The drain hole is blocked.
Clean the condensate channel and
^
drain hole.
If you still cannot remedy the fault having followed these suggestions, please contact the Miele Service Department.
To prevent unnecessary loss of temperature it is advisable not to open the doors while waiting for the appliance to be serviced.
Problem solving guide
31
Page 32
Noises
Normal noises What causes them
Brrrrr... Humming noise made by the motor (compressor). This noise can
Blubb, blubb.... A gurgling noise can be heard when coolant is circulating
Click.... Clicking sounds are made when the thermostat switches the
Sssrrrrr.... On multi-zone and frost-free appliances you can sometimes just
Creak ... Creaking sounds can be heard when material inside the
Remember that the noise of the compressor and the coolant circulating in the system is unavoidable.
get louder for brief periods when the motor is switching on.
through the pipes.
motor on and off.
hear the movement of air circulating inside the appliance.
appliance expands.
Noises that you can easily rectify
Rattling, vibrating The appliance is uneven: Realign the appliance using a spirit
What causes them, and what can you do about them
level, by raising or lowering the screw feet underneath the appliance.
The appliance is touching another appliance or piece of furniture: Move it away.
Drawers, baskets or shelves are unstable or sticking: Check
all removable items and refit them correctly.
Are any bottles or containers unstable or knocking against each other? Separate them.
The transport cable clips are hanging loose at the back of the appliance: Remove the clips.
32
Page 33
In the event of a fault which you cannot correct yourself, or if the appliance is under guarantee, please contact:
your Miele Dealer
or
Miele
(see back cover for contact details).
When contacting your Dealer or Miele, please quote the model and serial number of your appliance. This information is given on the data plate inside your appliance.
Please note that telephone calls may be monitored and recorded for training purposes.
N.B. A call-out charge will be applied for service visits where the problem could have been resolved as described in these instructions.
After Sales / Guarantee
Guarantee
For information on the appliance guarantee specific to your country please contact Miele. See back cover for contact details.
In the U.K. your appliance is guaranteed for 2 years from the date of delivery. However, you must activate your cover by calling 0845 365 6640 or registering online at www.miele.co.uk.
33
Page 34
Electrical connection
Electrical connection U.K.
All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current local and national safety (BS 7671 in the UK).
The appliance is supplied with a mains cable and moulded plug ready for connection to an a.c. single phase 220-240 V 50 Hz supply.
The voltage and frequency are given on the data plate. Please ensure that these match the household mains supply. The fuse rating is quoted on the plug.
Connection should be made via a suitable switched socket which is easily accessible. For extra safety it is advisable to protect the appliance with a suitable residual current device (RCD).
Do not connect the appliance to the mains electricity supply by an extension lead. Extension leads do not guarantee the required safety of the appliance (e.g. danger of overheating).
Non-rewireable plugs (BS 1363)
The fuse cover must be re-fitted when changing the fuse, and if the fuse cover is lost, the plug must not be used until a suitable replacement is obtained. The colour of the correct replacement cover is that of the coloured insert in the base of the plug, or the colour that is embossed in words in the base of the plug (as applicable to the design of the plug fitted).
Replacement fuses should be ASTA approved to BS 1362 and have the correct rating. Replacement fuses and fuse covers may be purchased from your local electrical supplier.
WARNING THIS APPLIANCE MUST BE EARTHED
This appliance must not be connected to the inverter of an autonomous power supply, e.g. a solar power system. When switching the appliance on, a surge in power could trigger the safety cut-out mechanism. This could damage the electronic unit.
The appliance must not be used with so-called energy saving devices. These reduce the energy supply to the appliance which could then become too warm. Using such devices could alter the specification of the product.
34
Page 35
Installation
Do not place any appliance which gives off heat, such as a toaster or microwave oven, on top of this appliance, as this would increase the appliance's energy consumption.
This appliance must not be installed directly next to another refrigerator or freezer. It does not have side-wall heating, so installation next to another refrigerator or freezer could cause a build-up of condensation between them. Further information is available from your dealer.
Location
This appliance should be installed in a dry, well-ventilated room. It should not be installed where it is exposed to direct sunlight or directly adjacent to a heat-producing appliance such as an oven or a radiator. The room temperature should not go above or below the climate range for which the appliance is designed. The higher the ambient temperature of the room, the more energy the appliance requires to operate.
Important: tropical / humid environments
During periods of high humidity, some condensation may appear on outside surfaces of cooling appliances. This condensation will disappear when humidity levels drop. For prevention, it is advisable to install the appliance with sufficient ventilation in a dry and/or an air-conditioned room. Please ensure that doors are closing and sealing properly. Please ensure that the appliance is installed in accordance with these installation instructions and that the handle is fitted correctly. Should you require further assistance please contact your Miele customer service centre.
35
Page 36
Installation
Climate range
The appliance is designed for use within certain climate ranges (ambient temperatures), and should not be used outside this range. The climate range of the appliance is stated on the data plate inside the appliance.
Climate range Ambient room
SN
N
ST
T
SN-ST
SN-T
temperature
+10°C to +32°C +16°C to +32°C +16°C to +38°C +16°C to +43°C +10°C to +38°C +10°C to +43°C
Operating in a room which is too cold will result in the cooling system switching off for too long, causing the internal temperature in the appliance to rise with the risk of frozen food deteriorating and going off.
Ventilation
Installation
Remove the cable clip from the back
^
of the appliance.
Check that all parts at the back of the
^
appliance are unhindered. Carefully remove any hindrance.
Carefully push the appliance into
^
position with the back against the wall.
Aligning the appliance
^ To align the appliance, adjust the feet
using the spanner supplied.
Air at the back of the appliance gets warm. To ensure sufficient ventilation, the ventilation gaps must not be covered over. The air inlet and outlet must not be covered or blocked in any way. They should be dusted on a regular basis.
36
Page 37
Appliance dimensions
Installation
ABC
KD 12823 S 1817 mm 600 mm 631 mm
37
Page 38
Changing the door hinging
The appliance is supplied right-hand hinged. If left-hand door hinging is required, follow the instructions below.
To change the door hinging you will need the following tools:
a cross-slotted screwdriver,
a flat-bladed screwdriver,
a selection of Torx screwdrivers,
a spanner.
Two people are needed for changing the door hinging.
Removing the door handles:
^
Pull door handle a towards you. Side section b slides back.
^
Pull side section b out of the guides on the mounting plate.
^
Undo the 4 screws (Torx 15) in the mounting plate, and remove the handle.
^
Remove the cover caps from the opposite side, and fit them into the empty holes.
38
Page 39
Changing the door hinging
To remove the doors:
Make sure the door shelves are empty.
Close the upper door.
^
^ Remove cover a by sliding it
forwards from the back and then lifting it off.
^ Remove cover b by pulling it
upwards.
Caution. The upper door is not secure as soon as the upper hinge plate is removed.
Then fit cover e from the front over
^
retaining plate f, and slide it over to the right. The writing must be visible.
Remove cover g, then rotate it by
^
180° and fit it on the opposite side.
Then fit cover e together with
^
retaining plate f on the opposite side.
^
Loosen screws d in upper hinge plate c and pull it upwards and off.
^
Carefully lift the upper door off and place it to one side.
^
Carefully loosen cover e from above using a screwdriver and then take it off together with retaining plate f.
^
Then separate retaining plate f from cover e, by pushing it slightly to the left. Then pull the cover forwards and off.
^
Rotate retaining plate f by 180°.
39
Page 40
Changing the door hinging
Close the lower appliance door.
^
Pull plastic cover h off.
^ ^ Pull the middle hinge pin i upwards
to remove it.
^ Carefully lift the lower door off and
place it to one side.
^ Pull cover j off. ^ Unscrew hinge plate k, turn it
through 180° and fit it on the opposite side.
^ Turn plastic cover h 180° and refit it
in the centre of hinge plate k.
^
Refit cover j on the opposite side.
^ Remove cap l from the bearing
bush in the door and refit on the opposite side.
^ Remove spring clamp m from
underneath the door and fit it on the opposite side.
40
Page 41
Changing over the doors:
Remove cover a by pulling it
^
forwards.
^ With the help of another person,
carefully tilt the appliance backwards and pull hinge pin b out.
^ Do not lose hinge bush c. ^ Undo screws d and take hinge plate
e off.
^ Remove cover f and fit it into the
holes on the opposite side.
^
Unscrew bearing g from hinge plate e and screw it into the hole on the other side of hinge plate e.
Changing the door hinging
Screw hinge plate e into position on
^
the opposite side using the two outer long slots only. Do not use the middle hole because you will not be able to align the door later on.
^ Using a second person, carefully tip
the appliance backwards and then fit hinge pin b together with hinge bush c from below into hinge plate e on the left hand side.
^ Refit cover a on the left. ^ Place the lower door onto hinge pin
b.
^
Close the lower appliance door.
^
Fit hinge pin i into middle hinge plate k in the lower door.
^
Then fit the top door on middle hinge pin i.
41
Page 42
Changing the door hinging
Fit hinge plate c onto the opposite
^
side and secure it with screws d. If necessary drill pilot holes for the screws or use a battery operated screwdriver.
^ Fit covers a and b to their opposite
sides.
^ Align the door with the appliance
housing using the long slots in the lower hinge plate. Then tighten the screws.
Refitting the handle:
Please make sure you follow the instructions below carefully when you refit the handle. The door seal will be damaged if the handle is fitted incorrectly.
^ Loosely attach the handle to the
opposite side of the door with the two front screws b.
42
Mounting plate c must be positioned on the side of the door so that when the door is closed it is flush with the side of the appliance. If this is not the case,
^
tighten both grub screws a with a suitable allen key until mounting plate c lines up correctly.
^
Then tighten all 4 fixing screws b.
^
Slide the side section of the handle d into the guides on the mounting plate until it clicks into place.
Page 43
It is important to check that the side section of the handle d does not come into contact with the door seal when opening the door, as this would damage the door seal permanently.
If, after you have refitted the handle, you find that the side section does touch the door seal when the door is opened:
Realign mounting plate c with grub screws a until the mounting plate and the side section of the handle d are at the correct angle and the side section does not touch the door seal when the door is opened.
Changing the door hinging
43
Page 44
Aligning the appliance doors
The appliance doors can be aligned with the housing at a later date.
In the following illustration the door is not shown in the closed position to make it easier to see what happens next.
To align the lower door use the long outer slots in the lower hinge plate:
^ Remove centre screw a from the
hinge plate.
^ Slightly loosen both outer screws b.
To align the upper door use the long outer slots in the middle hinge plate:
Remove centre screw a from the
^
hinge plate.
Slightly loosen both outer screws b.
^ ^ Align the door by sliding the hinge
plate to the left or right.
^ Then tighten screws b again. Screw
a does not need to be refitted.
^
Align the door by sliding the hinge plate to the left or right.
^
Then tighten screws b again. Screw a does not need to be refitted.
44
Page 45
a Top box
b Appliance
Building in the appliance
The air inlet and outlet must not be covered or blocked in any way. They should be dusted on a regular basis.
When built into a kitchen run (max. depth 580 mm) the appliance can be installed directly next to a kitchen furniture housing unit. The appliance door will protrude in front of furniture fronts at the sides by 34 mm and by 55 mm in the middle of the door. This enables the doors to be opened and shut without being obstructed.
When installed next to a wall d a distance of approx. 55 mm must be maintained on the hinge side between the wall d and the appliance b,so that the doors and the handles have sufficient space for opening.
c Housing unit
d Wall
The appliance can be installed in a kitchen run. To match the height of the rest of the kitchen, the appliance can be fitted with a suitable top box a.
A ventilation gap of at least 50 mm depth must be allowed for behind the appliance across the entire width of the top box for air to circulate. The cross section of the air outlet under the room ceiling must be at least 300 cm
2
to ensure that air can circulate without hindrance. Otherwise the appliance has to work harder, resulting in an increase in electricity consumption.
454647
Page 46
Page 47
Page 48
Alteration rights reserved / 1810
KD 12823 S
M.-Nr. 07 680 530 / 01
Loading...