Page 1
Operating instructions
for dishwashers
To avoid the risk of accidents or damage to the appliance, it is essential
to read these instructions as well as the installation plan before it is
installed and used for the first time.
en-AU, NZ M.-Nr. 10 601 510HG05
Page 2
2
Page 3
Contents
Guide to the appliance.......................................................................................... 6
Guide to the appliance ............................................................................................ 6
Control panel........................................................................................................... 7
Display..................................................................................................................... 8
Warning and Safety instructions.......................................................................... 9
Caring for the environment ................................................................................ 19
Energy-saving dishwashing................................................................................... 20
EcoFeedback consumption indicator.................................................................... 21
Before using for the first time ............................................................................ 22
Opening the door .................................................................................................. 22
Closing the door.................................................................................................... 22
Basic settings........................................................................................................ 23
Before using the appliance for the first time, you require: .................................... 25
Dishwasher salt ..................................................................................................... 25
Filling the salt reservoir..................................................................................... 26
Add salt reminder ............................................................................................. 27
Rinse aid................................................................................................................ 28
Adding rinse aid ...............................................................................................28
Add rinse aid reminder ..................................................................................... 29
Loading the dishwasher...................................................................................... 30
Notes ..................................................................................................................... 30
FlexAssist .............................................................................................................. 32
Upper basket......................................................................................................... 32
Adjusting the upper basket ..............................................................................33
Lower basket......................................................................................................... 34
Cutlery ................................................................................................................... 36
3D cutlery tray + (depending on model)........................................................... 36
Cutlery basket (depending on model) ..............................................................38
Loading examples ................................................................................................. 39
Dishwashers with cutlery tray........................................................................... 39
Dishwashers with cutlery basket......................................................................41
Comparison tests ................................................................................................ 43
Standard height with cutlery tray .......................................................................... 43
XXL height with cutlery tray................................................................................... 46
Operation.............................................................................................................. 49
Detergent............................................................................................................... 49
Adding detergent.............................................................................................. 51
Switching on.......................................................................................................... 52
3
Page 4
Contents
Selecting a programme ......................................................................................... 52
Starting the programme ........................................................................................ 53
Time display .......................................................................................................... 53
Energy management ............................................................................................. 54
At the end of the programme ................................................................................ 54
Switching off.......................................................................................................... 55
Unloading the dishwasher..................................................................................... 55
Interrupting a programme...................................................................................... 56
Changing a programme......................................................................................... 56
Programme options............................................................................................. 57
Options.................................................................................................................. 57
FlexiTimer with EcoStart ....................................................................................... 58
DetergentAgent ..................................................................................................... 61
Programme chart ................................................................................................62
Further programmes ........................................................................................ 66
Cleaning and care ............................................................................................... 67
Cleaning the wash cabinet .................................................................................... 67
Cleaning the door and the door seal..................................................................... 67
Cleaning the control panel .................................................................................... 67
Cleaning the reflector panel .................................................................................. 67
Cleaning the door front ......................................................................................... 68
Checking the filters in the wash cabinet ............................................................... 69
Cleaning the filters................................................................................................. 69
Cleaning the spray arms........................................................................................ 71
Problem solving guide ........................................................................................72
Technical problems ............................................................................................... 72
Water inlet fault ..................................................................................................... 75
Water drainage fault .............................................................................................. 76
General problems.................................................................................................. 77
Noises.................................................................................................................... 78
Unsatisfactory washing result ............................................................................... 79
Maintenance ........................................................................................................82
Cleaning the water inlet filter................................................................................. 82
Cleaning the drain pump and non-return valve..................................................... 83
After sales service............................................................................................... 84
Repairs .................................................................................................................. 84
Warranty ................................................................................................................ 84
Optional accessories ..........................................................................................85
4
Page 5
Contents
Electrical connection ..........................................................................................87
Water connection ................................................................................................ 88
The Miele Waterproof system................................................................................ 88
Connection to the water supply ............................................................................ 88
Drainage ................................................................................................................ 90
Technical data...................................................................................................... 91
Technical data ....................................................................................................... 91
Settings menu...................................................................................................... 92
Opening the Settings menu................................................................................... 92
Language ........................................................................................................... 93
Time of day............................................................................................................ 93
Water hardness ..................................................................................................... 94
Rinse aid................................................................................................................ 95
Consumption (EcoFeedback)................................................................................ 95
EcoStart................................................................................................................. 96
Soak ...................................................................................................................... 98
Pre-wash ............................................................................................................... 98
Brightness ............................................................................................................. 98
Volume................................................................................................................... 98
Switching off the refill reminders........................................................................... 99
Check filters .......................................................................................................... 99
Automatic .............................................................................................................. 99
AutoOpen .............................................................................................................. 99
Optimise standby ................................................................................................ 100
Heat exchanger ................................................................................................... 100
Software version.................................................................................................. 101
Showroom programme........................................................................................ 101
Factory default settings....................................................................................... 101
Closing the Settings menu .................................................................................. 101
5
Page 6
Guide to the appliance
Guide to the appliance
a
Upper spray arm (not visible)
b
Cutlery tray (depending on model)
c
Upper basket
d
Middle spray arm
e
Heat exchanger return (depending on
model)
f
Lower spray arm
6
g
Filter combination
h
Data plate
i
Rinse aid reservoir
j
Dual compartment detergent
dispenser
k
In-operation indicator light
l
Salt reservoir
Page 7
Control panel
Guide to the appliance
a
In-operation indicator light
b
Programme selection
c
Short and Energy save option
buttons with indicator lights
d
Arrow buttons
e
button (FlexiTimer) with indicator
light
These operating instructions apply to several different dishwasher models with
different heights.
The specific dishwasher models are referred to as follows:
Standard = 80.5 cm high dishwashers (integrated)
and 84.5 cm high dishwashers (freestanding)
XXL = 84.5 cm high dishwashers (integrated)
f
OK button
g
Display
h
Programme selector button
i
On/Off button
7
Page 8
Guide to the appliance
Display
General
The display is used to select or set the
following:
– the programme
– the FlexiTimer (Delay start)
– the Settings menu
The display can show the following:
– the stage the programme is at
– the estimated time left for the
programme to run
– the energy and water consumption
(EcoFeedback)
– any relevant fault messages and
information
To save energy, the dishwasher
switches off after a few minutes if you
do not press any buttons during this
time.
To switch the dishwasher back on
again, press the button.
Settings menu
The Settings menu is used to alter the
dishwasher's electronics to suit
different requirements. You access the
Settings menu by pressing a specific
button combination (see "Settings
menu").
The arrows in the display indicate
further options. You can use the
arrow buttons next to the display,
as appropriate, to select these further
options.
The OK button is used to confirm a
message or setting and also to move to
the next menu or another level.
The option which is selected will have a
tick next to it.
To exit a sub-menu, use the arrow
buttons to select the Back option in
the display and confirm your selection
with OK.
If you do not press any of the buttons
for several seconds, the display will
return to the previous menu level. You
may need to enter your settings again.
8
Page 9
Warning and Safety instructions
This dishwasher complies with current safety requirements.
Inappropriate use can, however, lead to personal injury and
damage to property.
To avoid the risk of accidents and damage to the dishwasher,
please read the installation plan and the operating instructions
carefully before it is installed and used for the first time. They
contain important information on its installation, safety, use and
maintenance.
Keep the installation plan and the operating instructions in a safe
place and pass them on to any future owner.
Miele cannot be held liable for damage caused by non-compliance
with this information.
9
Page 10
Warning and Safety instructions
Correct application
This appliance is designed for domestic use and for use in similar
environments by guests in hotel or motel rooms, bed & breakfasts
and other typical living quarters. This does not include common/
shared facilities or commercial facilities within hotels, motels or bed
& breakfasts.
This dishwasher is not suitable for outdoor use.
It must only be used as specified in these operating instructions
for cleaning domestic crockery and cutlery. Any other usage is not
supported by the manufacturer and could be dangerous.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning its use by a person responsible
for their safety, and are able to recognise the dangers of misuse.
10
Page 11
Warning and Safety instructions
Safety with children
Young children must not be allowed to use this appliance.
Older children may only use the appliance when its operation has
been clearly explained to them and they are able to use it safely,
recognising the dangers of misuse.
Cleaning work may only be carried out by older children under the
supervision of an adult.
Children should be supervised to ensure that they do not play with
the appliance. Keep small children away from the appliance at all
times to avoid the risk of injury. There is the risk that children may
lock themselves in the dishwasher.
If the automatic door opening mechanism (depending on model) is
active, keep young children away from the area in which the door
opens. Danger of injury in the unlikely event of a fault with the
opening mechanism.
Danger of suffocation! Children may be able to wrap themselves in
packing material or pull it over their heads with the risk of
suffocation. Keep children away from any packing material.
Keep detergent and other household agents out of the reach of
children at all times. Some dishwasher detergents are strongly
alkaline and contain irritants and corrosive ingredients. They can be
extremely dangerous if swallowed, and can cause burning in the
mouth, nose and throat, or inhibit breathing. Avoid contact with the
skin and eyes. Keep children away from the dishwasher when the
door is open. There could still be detergent residues in the cabinet or
dispenser. Check that the dispenser is empty after the completion of
a programme. Seek medical advice immediately if your child has
swallowed or inhaled detergent, e.g. Poisons Information Centre
(Australia) or National Poisons Centre (NZ).
11
Page 12
Warning and Safety instructions
Technical safety
Repairs and other work by unqualified persons could be
dangerous. Installation, maintenance work and repairs to electrical
appliances must only be carried out by a Miele approved service
technician.
Before installation, check the dishwasher for visible signs of
damage. Under no circumstances should you use a damaged
dishwasher. A damaged dishwasher could be dangerous.
The electrical safety of this appliance can only be guaranteed
when continuity is complete between it and an effective earthing
system. It is most important that this basic safety requirement is
present and regularly tested and, where there is any doubt, the
electrical system in the house should be checked by a qualified
electrician.
Miele cannot be held liable for the consequences of an inadequate
earthing system (e.g. electric shock).
Reliable and safe operation of this dishwasher can only be
assured if it has been connected to the mains electricity supply.
The dishwasher must only be plugged into the electricity supply
via a suitable switched socket. The electrical socket must be easily
accessible after the dishwasher is installed so that it can be
disconnected from the electricity supply at any time.
There must be no electrical sockets behind the dishwasher.
Danger of overheating and fire risk if the dishwasher were to be
pushed up against a plug.
The dishwasher must not be installed under a cooktop. The high
radiant temperatures which are sometimes generated by a cooktop
could damage the dishwasher. For the same reason, it should not be
installed next to open fires or other appliances which give off heat,
such as heaters etc.
12
Page 13
Warning and Safety instructions
To avoid the risk of damage to the dishwasher, make sure that the
connection data on the data plate (fuse rating, voltage and
frequency) matches the mains electricity supply before connecting
the dishwasher to the mains. Consult a qualified electrician if in any
doubt.
Do not connect the dishwasher to the mains supply until it has
been fully installed and any adjustment has been made to the door
springs.
The dishwasher may only be operated if the door opening
mechanism is working correctly. Otherwise there could be a risk of
injury whilst the automatic door opening mechanism (depending on
model) is active.
To check that the door opening mechanism is working correctly:
– the door springs must be adjusted equally on both sides. They
are correctly adjusted when the door remains stationary when left
half open (approx. 45° opening angle). It is also important that the
door cannot fall open.
– the door locking pins automatically retract when the door opens
at the end of the drying phase.
Do not connect the appliance to the mains electricity supply by a
multi-socket adapter or an extension lead. These do not guarantee
the required safety of the appliance (e.g. danger of overheating).
This appliance must not be installed and operated in mobile
installations (e.g. on a ship).
Do not install the dishwasher in a room where there is a risk of
frost. Frozen hoses may burst or split. The reliability of the electronic
control unit may be impaired at temperatures below freezing point.
To avoid any damage to the appliance, the dishwasher must only
be operated when it is connected to a fully vented plumbing system.
The plastic housing of the water connection contains an electrical
valve. The housing must not be dipped in water.
13
Page 14
Warning and Safety instructions
There are electrical wires in the water inlet hose. Do not cut the
water inlet hose, even if it is too long.
The integrated Waterproof system offers protection from water
damage, provided the following conditions are met:
– The dishwasher is correctly installed and plumbed in.
– The dishwasher is properly maintained and parts are replaced
where it can be seen that this is necessary.
– The tap has been turned off when the appliance is not used for a
longer period of time (e.g. during holidays).
The Waterproof system will work even if the appliance is switched
off. However, the appliance must remain connected to the electricity
supply.
The water pressure (flow pressure at the connection point) must
be between 50 and 1000 kPa (0.5 and 10 bar).
A damaged appliance could be dangerous. If the dishwasher gets
damaged, switch it off at the mains and call Miele.
The manufacturer's warranty will be invalidated if the appliance is
not repaired by a Miele approved service technician.
Faulty components must only be replaced by genuine Miele spare
parts. The manufacturer can only guarantee the safety of the
appliance when Miele replacement parts are used.
During installation, maintenance and repair work, the appliance
must be disconnected from the mains electricity supply.
If the mains connection cable is damaged, it must be replaced
with a special cable of the same type (available from Miele) by a
Miele authorised service technician only in order to avoid a hazard.
14
Page 15
Warning and Safety instructions
This dishwasher is supplied with a special lamp (depending on
model) to cope with particular conditions (e.g. temperature,
moisture, chemical resistance, abrasion resistance and vibration).
This special lamp must only be used for the purpose for which it is
intended. It is not suitable for room lighting. Replacement lamps may
only be replaced by a Miele authorised technician.
In areas which may be subject to infestation by cockroaches or
other vermin, pay particular attention to keeping the appliance and
its surroundings in a clean condition at all times. Any damage which
may be caused by cockroaches or other vermin will not be covered
by the warranty.
15
Page 16
Warning and Safety instructions
Correct installation
The dishwasher must be installed and connected in compliance
with the installation instructions.
Be careful when installing the dishwasher. Wear
protective gloves to avoid injury on any sharp metal
components.
The dishwasher must be correctly aligned to ensure problem-free
operation.
In order to ensure stability, built-under and integrated dishwashers
must only be installed under a continuous worktop which is secured
to adjacent cabinetry.
If you want to convert your freestanding dishwasher to a built-
under ("U") model, you will need to order the appropriate conversion
kit. If you remove the existing plinth, you must replace it with a Umodel plinth. This is necessary to avoid the risk of injury caused by
protruding metal parts.
The door springs on either side need to be evenly adjusted. They
are correctly adjusted if the half-opened door (approx. 45° door
opening angle) remains in this position when it is released. The door
must not fall down under its own weight.
The appliance may only be used with correctly adjusted door
springs.
16
Page 17
Warning and Safety instructions
Correct use
Do not use solvents in the dishwasher. Danger of explosion!
Do not inhale or ingest dishwasher detergent. Some dishwasher
detergents are strongly alkaline and contain irritants or corrosive
ingredients. They can be extremely dangerous if swallowed, and can
cause burning in the nose, mouth and throat, or inhibit breathing.
Avoid contact with the skin and eyes. Seek medical advice
immediately if detergent has been swallowed or inhaled, e.g. Poisons
Information Centre (Australia) or National Poisons Centre (NZ).
Avoid leaving the door open unnecessarily as someone could trip
over it and be injured by it.
Do not sit or lean on the opened door. This could cause the
dishwasher to tip and be damaged, and you could get injured.
Dishes can be very hot at the end of a programme. Allow them to
cool until they are comfortable enough to handle before unloading.
Only use detergent and rinse aid formulated for domestic
dishwashers. Do not use washing-up liquid.
Do not use commercial or industrial detergents as these may
cause damage, and there is a risk of a severe explosive chemical
reaction (such as an explosive oxyhydrogen gas reaction).
Do not fill the rinse aid reservoir with powder or liquid detergent.
This will cause serious damage to the reservoir.
Inadvertently filling the salt reservoir with powder or liquid
dishwasher detergent will damage the water softener. Make sure you
have picked up the correct packet of dishwasher salt before filling
the salt reservoir!
Only use special coarse grained dishwasher salt for reactivation.
Do not use other salts such as cooking salt, agricultural grade or
gritting salt. These may contain insoluble additives which can impair
the functioning of the water softener.
17
Page 18
Warning and Safety instructions
In an appliance with a cutlery basket (depending on model) cutlery
is cleaned and dried more efficiently if placed in the basket with the
handles downwards. However, to avoid the risk of injury, place
knives and forks etc. with the handles upwards.
Plastic items which cannot withstand being washed in hot water,
such as disposable plastic containers, or plastic cutlery and crockery
should not be cleaned in the dishwasher. The high temperatures in
the dishwasher may cause them to melt or lose shape.
If you use the "FlexiTimer/Delay start" option (depending on
model), make sure that the dispenser is dry before adding detergent.
Wipe dry if necessary. Detergent will clog if poured into a damp
dispenser and may not be thoroughly dispersed.
Please observe the information given in "Technical data" regarding
the capacity of the dishwasher.
Accessories
Use only genuine original Miele spare parts. If spare parts or
accessories from other manufacturers are used, the warranty will be
invalidated, and Miele cannot accept liability.
Disposal of your old dishwasher
Make the door lock inoperative so that children cannot
accidentally shut themselves in. Remove or destroy the locking
bracket of the door lock, and make appropriate arrangements for the
disposal of the appliance.
18
Page 19
Caring for the environment
Disposal of the packing material
The transport and protective packaging
has been selected from materials which
are environmentally friendly for
disposal, and can normally be recycled.
Recycling the packaging reduces the
use of raw materials in the
manufacturing process and also
reduces the amount of waste in landfill
sites. Ensure that any plastic
wrappings, bags etc. are disposed of
safely and kept out of the reach of
babies and young children. Danger of
suffocation.
Disposing of your old appliance
Electrical and electronic appliances
often contain valuable materials. They
also contain specific materials,
compounds and components, which
were essential for their correct function
and safety. These could be hazardous
to human health and to the environment
if disposed of with your domestic waste
or if handled incorrectly. Please do not,
therefore, dispose of your old appliance
with your household waste.
Please dispose of it at your local
community waste collection / recycling
centre for electrical and electronic
appliances. You are also responsible for
deleting any personal data that may be
stored on the appliance prior to
disposal. Please ensure that your old
appliance poses no risk to children
while being stored prior to disposal.
19
Page 20
Caring for the environment
Energy-saving dishwashing
This dishwasher is exceptionally
economical in its use of water and
electricity.
You can make the most of your
appliance by following these tips:
– For most economical dishwashing,
make full use of the baskets without
overloading the dishwasher.
– Choose the programme to suit the
type of crockery being washed and
the degree of soiling.
– Select the ECO programme for
energy-saving dishwashing. This
programme is the most efficient in
terms of its combined energy and
water consumption at cleaning
normally soiled crockery.
– If your dishwasher is connected to a
hot water supply, select the SolarSave
programme for washing a lightly to
moderately soiled load. Because the
water is not heated in this
programme, crockery may still be
slightly damper at the end of this
programme than it would be with
other programmes.
– Follow the detergent manufacturer's
recommendations on detergent
dosage.
– When using powder or liquid
detergent you can use 1/3 less
detergent if baskets are only half full.
You can find further tips on energysaving dishwashing in "Miele's guide
to dishwashing".
20
Page 21
Caring for the environment
EcoFeedback consumption indicator
The Consumption function is used for
calling up information about the energy
and water consumption of your
dishwasher (see "Settings menu Consumption").
Three different types of information can
be displayed:
– an estimate of the consumption
before the programme begins
– the actual consumption at the end of
the programme
– the total consumption of the
dishwasher
1. Consumption estimate:
After a programme has been selected,
first the name of the programme and,
after a few seconds, the estimated
energy and water consumption will
appear in the display.
2. Actual consumption
At the end of the programme you can
call up the actual amount of energy and
water used by the programme which
has just been run.
Open the door at the end of the
programme.
Press OK when the Consumption (OK)
message appears in the display.
Switching the dishwasher off at the
end of the programme will delete the
actual consumption values for the
programme which has just been run.
3. "Consumption" setting
The Consumption setting gives a total of
the energy and water which has been
used in all previous dishwasher
programmes (see "Settings menu Consumption").
The estimated consumption levels will
be displayed as a bar chart. The more
bars () in the display, the more
energy or water will be used.
The values are influenced by the
programme selected and any
programme options selected.
The display will change automatically to
show the time remaining.
The consumption indicator is switched
on as standard. However, you can also
switch the indicator off (see "Settings
menu - Consumption").
21
Page 22
Before using for the first time
Opening the door
At the end of programmes with a drying
phase (see "Programme chart"), the
door will open automatically a little in
order to help the drying process.
This function can be deactivated if
preferred (see "Settings menu AutoOpen").
Pull the handle.
Open the door fully so that the door
catch rail retracts again.
Closing the door
Push the baskets right in.
Then lift the door upwards and push
until it clicks into position.
Danger of injury!
Do not put your hand inside the door
as it is closing.
If the door is opened during operation,
all functions are automatically
interrupted.
Water in the dishwasher may be
hot. Danger of scalding!
Only open the door during operation
if absolutely necessary and exercise
extreme caution when doing so.
Keep the area around the door
free of obstructions.
22
Page 23
Before using for the first time
Basic settings
Open the door.
Switch the dishwasher on with the
button.
The welcome screen will appear when
the dishwasher is switched on for the
first time.
Language
The display will change automatically to
the screen for setting the language.
Use the arrow buttons to select
the language you want and also the
country, if appropriate, and confirm
your selection with OK.
To learn about the display, read the
section with the same name.
A tick will appear next to the
language that has been set.
Time of day
The display will then change to the
screen for setting the time.
The current time of day must be set
before you can use the "FlexiTimer"
programme option.
Use the arrow buttons to set the
hour and confirm with OK.
Then set the minutes and confirm
with OK.
Keeping the arrow buttons
pressed in will increase or decrease
the time automatically.
23
Page 24
Before using for the first time
Water hardness
The display will change to the screen
for setting the water hardness.
– The dishwasher must be
programmed to the correct water
hardness for your area.
– Your local water authority will be able
to advise you of the water hardness
level in your area.
– Where the water hardness fluctuates
e.g. between 1.8 and 2.7mmol/l (1015°d - German scale), always
programme the dishwasher to the
higher value (2.7mmol/l or 15°d in
this example).
In the event of a fault, it will help the
service technician if you know the
hardness of your local water supply.
Enter the water hardness below:
____________mmol/l
The dishwasher is programmed at the
factory for a water hardness level of 0.2
mmol/l (1°d - German scale).
Finally, prompts will appear in the
display.
After confirming these prompts with
OK, the messages Add salt and
Add rinse aid may appear.
Add salt and rinse aid if necessary
(see "Before using for the first time Dishwasher salt" and "Rinse aid").
Confirm the messages with OK.
The programme selected will appear
briefly in the display and the
appropriate indicator light will come on.
Then, if applicable, the estimated
energy and water consumption for the
programme selected will appear for a
few seconds.
Finally, the display will show the
estimated programme duration for the
programme selected.
Use the arrows to select the
hardness of your water supply and
confirm with OK.
See "Settings menu - Water hardness"
for more information.
24
Page 25
Before using for the first time
Before using the appliance for the first time, you require:
– approx. 2 litres of water,
– approx. 2 kg dishwasher salt,
– domestic dishwasher detergent,
– rinse aid formulated for domestic
dishwashers.
Every dishwasher is tested at the
factory. There will be residual water in
the appliance from this test. It is not
an indication that it has been used
previously.
Dishwasher salt
In order to achieve good cleaning
results, the dishwasher needs to
operate with soft water. Hard water
results in a build-up of calcium deposits
on crockery and in the dishwasher.
Mains water with a hardness level
higher than 0.7mmol/l (4°d - German
scale) needs to be softened. This takes
place automatically in the integrated
water softener. The water softener in
the dishwasher is suitable for a water
hardness level of up to 12.6 mmol/l
(70°d - German scale).
If the water in your area is very soft
and constantly lower than 0.9mmol/l
(5°d - German scale), you do not
have to add dishwasher salt. The
prompt to add salt will be switched off
automatically if the water softener has
been programmed for this to happen.
Dishwasher detergent will
damage the water softener.
Do not fill the salt reservoir with
powder or liquid detergent.
Only use special coarse grained
dishwasher salt for reactivation,
as other salts (e.g. cooking salt,
agricultural grade or gritting salt) may
contain insoluble additives which can
impair the functioning of the water
softener.
The water softener requires dishwasher
salt.
Depending on the water hardness level
(< 3.8mmol/l, or 21°d - German scale),
dishwasher salt is not required if
combination tablets are being used (see
"Operation, Detergent").
25
Page 26
Before using for the first time
Filling the salt reservoir
Before filling the salt reservoir with
dishwasher salt for the first time, you
must fill it with approx. 2litres of
water to enable the salt to dissolve.
Once the dishwasher has been used,
there is always sufficient water in the
reservoir.
Remove the lower basket and
unscrew the salt reservoir cap.
Water or saline solution will run out
of the reservoir when the cap is
removed.
It should therefore only be removed
in order to refill the salt reservoir.
Fill the reservoir with approx.2litres
of water (first use only).
Place the funnel provided over the
salt reservoir and carefully fill with
dishwasher salt until the reservoir is
full. The salt reservoir holds approx.
2kg of salt depending on the brand
used.
Clean any excess salt from around
the reservoir opening and then screw
the cap on again firmly.
26
Immediately after filling the salt
reservoir, run the QuickPowerWash
programme with the Short option and
without any crockery in the
dishwasher to dissolve and remove
any traces of salt from the cabinet.
Page 27
Before using for the first time
Add salt reminder
Fill the salt reservoir with dishwasher
salt for reactivation when Add salt
appears in the display (If it appears
during a programme, wait until the
end of the programme).
Confirm with OK.
The refill reminder will go out.
Risk of corrosion!
Immediately after filling the salt
reservoir, run the QuickPowerWash
programme with the Short
programme option selected and
without any crockery in the
dishwasher to remove any traces of
salt from the cabinet.
After the salt reservoir has been filled,
the refill reminder may still appear in the
display if the salt concentration has not
yet reached the correct level. If this is
the case, confirm again with OK.
If you only ever use multi-function
combination products in your
dishwasher, you can switch off both
refill reminders for salt and rinse aid if
you wish (see "Settings menu Switching off the refill reminders").
If you switch to using detergent that
does not contain salt or rinse aid, it
is important to remember to add
dishwasher salt and rinse aid and to
switch the reminders back on.
The refill reminder will be switched off if
you have programmed the dishwasher
for a water hardness below 0.9mmol/l
(5°d - German scale).
27
Page 28
Before using for the first time
Rinse aid
Rinse aid is necessary to ensure water
does not cling and leave marks on
crockery during the drying phase and
helps crockery dry faster after it has
been washed.
Rinse aid is poured into the storage
reservoir and the amount set is
dispensed automatically.
Inadvertently filling the rinse aid
reservoir with powder or liquid
detergent will damage the reservoir.
Only pour rinse aid formulated for
domestic dishwashers into the
reservoir.
Alternatively, it is possible to use
– household vinegar with a max. 5%
acid content
or
– liquid citric acid up to 10% acid
content
If you only ever use combination
products containing rinse aid in your
dishwasher, you do not need to add
rinse aid.
Adding rinse aid
Press the button on the lid of the
rinse aid reservoir in the direction of
the arrow until the flap springs open.
The resulting rinsing and drying quality
will not, however, be as good as when
rinse aid is used.
Do not use vinegar with a higher
acid content (e.g. vinegar essence
25% acid).
This would damage the dishwasher.
28
Page 29
Add rinse aid only until it is visible in
the opening.
The rinse aid reservoir holds approx.
110 ml.
Close the flap firmly so that it clicks
into place. Otherwise water can enter
the rinse aid reservoir during a
programme.
Before using for the first time
Add rinse aid reminder
When the Add rinse aid message
appears in the display, the reservoir
contains sufficient rinse aid for 2 - 3
programmes only.
Add rinse aid in plenty of time.
Confirm with OK.
The refill reminder will go out.
If you only ever use multi-function
combination products in your
dishwasher, you can switch off both
refill reminders for salt and rinse aid if
you wish (see "Settings menu Switching off the refill reminders").
If you switch to using detergent that
does not contain salt or rinse aid, it
is important to remember to add
dishwasher salt and rinse aid and to
switch the reminders back on.
Wipe up any spilled rinse aid. This
prevents over-foaming occurring
during the next programme.
You can adjust the rinse aid dosage
for best results (see "Settings menu Rinse aid").
29
Page 30
Loading the dishwasher
Notes
Remove coarse food residues from
crockery.
There is no need to rinse items under
running water.
Do not wash items soiled with
ash, sand, wax, lubricating grease or
paint in the dishwasher. Ash does
not dissolve and is distributed in the
wash cabinet. Wax, sand, lubricating
grease and paint cause damage to
the dishwasher.
Crockery can be loaded anywhere in
the baskets, but the following notes
should be observed:
– Do not place crockery and cutlery
inside other pieces where they may
be concealed.
– Load the crockery so that water can
access all surfaces. This ensures that
they get properly cleaned.
– Make sure that all items are securely
positioned.
– The spray arms must not be blocked
by items which are too tall or hang
through the baskets. If in doubt, test
for free movement by manually
rotating the spray arms.
– Make sure that small items cannot
fall through the holders in the
baskets.
Small items, e.g. lids, should
therefore be placed in the cutlery tray
or cutlery basket (depending on
model).
Some foodstuffs may contain natural
dyes, e.g. carrots, tomatoes or
tomato sauce. Plastic items in the
dishwasher may discolour if large
quantities of these foodstuffs find
their way into the dishwasher on the
crockery. The stability of plastic
items is not affected by this
discolouration.
Cleaning silver cutlery in the
dishwasher may also cause plastic
items to discolour.
– Hollow items such as cups, glasses,
pans, etc. must be inverted in the
basket.
– Tall, narrow, hollow items, e.g.
champagne glasses, should be
placed in the centre of the basket to
ensure better water coverage.
– Wide based items should be placed
at an angle so that water can run off
them freely.
30
Page 31
Loading the dishwasher
Items not suitable for dishwashers:
– Wooden cutlery and crockery or
items with wooden parts: these may
discolour and fade. The glue used in
these items is not dishwasher-proof
and wooden handles may come
loose after being washed in a
dishwasher.
– Craft items, antiques, valuable vases
and decorative glassware are also
not suitable for dishwashers.
– Plastic items which are not heat-
resistant: the high temperatures in
the dishwasher may cause them to
melt or lose shape.
– Copper, brass, tin and aluminium
items may discolour or become matt.
– Colours painted over a glaze may
fade after a number of washes.
– Delicate glassware and glassware
containing lead crystal: clouding may
occur over time.
Please note
Silverware previously cleaned with a
silver polish may still be damp or
spotted at the end of a programme,
where water has not run off smoothly. It
may need to be rubbed dry with a soft
cloth.
Aluminium components (e.g.
rangehood grease filters) must not be
cleaned with caustic alkaline
commercial or industrial cleaning
agents.
These may damage the material, or
in extreme cases, there is a risk of a
severe explosive chemical reaction
(such as an explosive oxyhydrogen
gas reaction).
Useful tip: When purchasing new
crockery and cutlery, make sure they
are dishwasher-proof.
Glass care
– Clouding may occur on glasses after
frequent washing. If delicate
glassware is washed in the
dishwasher, ensure that only very low
temperatures are used (see
programme chart), or a special glasscare programme is used (depending
on model). This will reduce the risk of
clouding.
– Purchase glassware which is
dishwasher-safe (e.g. Riedel
glassware).
– Use detergents with glass protective
additives.
Silver which has been in contact with
foods containing sulphur can discolour.
These include egg yolk, onions,
mayonnaise, mustard, pulses, fish, fish
brine and marinades.
31
Page 32
Loading the dishwasher
FlexAssist
The yellow coded FlexAssist parts
indicate which elements of the
dishwasher baskets and cutlery tray are
moveable. They also act as grips and
have symbols embossed on them to
show what the moveable parts are used
for.
Upper basket
See "Loading the dishwasher Loading examples" for examples of
how to load crockery and cutlery.
For safety reasons, do not
operate the dishwasher without the
upper and lower baskets in place
(except when running the Tall items
programme, if available).
Use the upper basket for small,
lightweight and delicate items such
as cups, saucers, glasses, dessert
bowls, etc.
Shallow pans or casserole dishes can
also be placed in the upper basket.
Cup rack
Raise the rack upwards using the
yellow lever to make room for tall
items.
Glasses can be arranged along the
positioning rail of the cup rack to give
them some support during the
programme.
Lower the cup rack and lean the
glasses against it.
Long items such as soup ladles,
mixing spoons and long knives
should be placed lying down across
the front of the upper basket.
32
Page 33
Loading the dishwasher
Adjusting the upper basket
In order to gain more space for taller
pieces of crockery in the bottom or
upper basket, the upper basket can be
adjusted on three levels with 2 cm
between each level.
The upper basket can also be set at an
angle with one side high and the other
side low. This can be useful to help
prevent water being left in deep dishes
etc. Ensure, however, that the basket
can be inserted smoothly into the
cabinet. It is better to adjust the basket
before loading it.
Pull out the upper basket.
Depending on the setting of the upper
basket, the following plate dimensions
can be accommodated.
Dishwashers with cutlery basket
(see data plate for model number)
Upper
basket
level
Top 20 24 31 (35*)
Middle 22 26 29
Bottom 24 28 27
Dishwashers with cutlery tray
(see data plate for model number)
Upper
basket
level
Plate in cm
Upper basket Lower
Stand-
ard
Upper basket Lower
Stand-
ard
XXL
Plate in cm
XXL
basket
basket
To raise the upper basket:
Pull the basket up until it clicks into
place.
To lower the upper basket:
Pull upwards on the levers at either
side of the upper basket.
Adjust the basket to the desired
height and then push the levers
securely back down into position.
Top 15 19 31 (35*)
Middle 17 21 29
Bottom 19 23 27
* When tilted, plates of up to 35 cm can be
accommodated (see "Lower basket").
33
Page 34
Loading the dishwasher
Lower basket
See "Loading the dishwasher Loading examples" for examples of
how to load crockery and cutlery.
For larger and heavier items such as
plates, serving platters, saucepans,
bowls, etc.
Glasses, cups and small items such
as saucers can also be placed in the
lower basket. Do not place thin,
delicate glassware in the lower
basket.
MultiComfort area
The rear section of the lower basket is
used for washing cups, glasses, plates,
pots and pans.
The glass rack can be raised to make
more room for tall items.
Stem glassware, e.g. wine glasses or
champagne flutes, can be leaned
against the glass holder or
suspended from it.
You can set the glass holder at two
different heights.
Place large platters and dishes in the
centre of the lower basket.
When tilted, plates up to 35cm in
diameter can be accommodated.
34
Slide the glass holder to the desired
height until the catches click into
place at the top or rest on the
bottom.
Page 35
Hinged spikes (depending on model)
The spikes at the front are used for
washing plates, soup bowls, platters,
dessert bowls and saucers.
Both rows of spikes can be lowered to
make more room for large items, e.g.
pots, pans and dishes.
Press the yellow lever downwards,
and then lower the spikes.
Loading the dishwasher
35
Page 36
Loading the dishwasher
Cutlery
3D cutlery tray + (depending on model)
See "Loading the dishwasher Loading examples" for examples of
how to load crockery and cutlery.
Arrange the cutlery in the tray as
shown.
To make unloading much easier, cutlery
should be grouped in zones, one for
knives, one for forks, one for spoons,
etc.
Spoon heads should be placed in
contact with at least one of the serrated
retainers on the base of the cutlery tray
to ensure that water runs off them
freely.
The upper spray arm must not be
blocked by items which are too big
(e.g. cake servers).
The side sections of the tray can be
moved into the middle using the yellow
grips in order to accommodate tall
items of crockery in the upper basket
(see also "Upper basket, glass rail").
If spoon handles do not fit between the
holders, then lay them the other way
round.
For optimum cleaning results, arrange
spoons with the inner part facing the
centre of the cutlery tray.
36
Page 37
You can use the yellow slide to adjust
the height of the middle section of the
cutlery tray to make more room for large
items of cutlery, such as serving
spoons and ladles.
Loading the dishwasher
Both rows of spikes in the middle
section of the cutlery tray can be
flipped over to make room for larger
pieces of cutlery.
Raise the spikes and then flip them
over.
37
Page 38
Loading the dishwasher
Cutlery basket (depending on model)
The cutlery basket can be placed
anywhere on the front rows of spikes in
the lower basket.
To avoid the risk of injury, knives and
forks should be placed with the
handles upwards in the basket.
However, cutlery placed handle down
in the basket will come out cleaner
and drier.
Fit it onto the cutlery basket if
required.
Place small items of cutlery in the
individual slots on three sides of the
cutlery basket.
Cutlery insert for the cutlery basket
Use the insert supplied for heavily
soiled items of cutlery. The insert
separates the items so that they can be
more easily accessed by water.
38
Insert cutlery with the handles facing
downwards.
Distribute them evenly along the
insert.
Page 39
Loading examples
Dishwashers with cutlery tray
Upper basket
Lower basket
Loading the dishwasher
39
Page 40
Loading the dishwasher
Cutlery tray
Heavily soiled items
40
Page 41
Dishwashers with cutlery basket
Upper basket
Lower basket
Loading the dishwasher
41
Page 42
Loading the dishwasher
Cutlery basket
Heavily soiled items
42
Page 43
Comparison tests
Standard height with cutlery tray
Test standard: AS/NZS 2007.1:2005, AS/NZS 2007.2:2005;
AS/NZS 6400:2005
Standard programme
for energy label comparison
tests:
Capacity: 14 place settings
Detergent quantity: 32.5 g in Compartment II
Rinse aid dispensing: Setting 3
You can find information on adjusting the rinse aid dosage in the "Rinse aid"
section of this booklet.
The door opens automatically during the drying phase.
Do not close the door until the drying test has finished.
Upper basket level:
Position: Bottom
Jumbo cup rack
(if available):
ECO
Outer position
Loading examples
Pictures illustrating how to load the dishwasher are shown on the following pages.
Picture : Upper basket
Picture : Lower basket
Picture : Cutlery tray
Do not lower or remove the basket inserts.
Remove the bottle holder from the lower basket
(if available).
43
Page 44
Comparison tests
Capacity
14
44
Page 45
Comparison tests
45
Page 46
Comparison tests
XXL height with cutlery tray
Test standard: AS/NZS 2007.1:2005, AS/NZS 2007.2:2005;
AS/NZS 6400:2005
Standard programme
for energy label comparison
tests:
Capacity: 15 place settings
Detergent quantity: 33.7 g in Compartment II
Rinse aid dispensing: Setting 3
You can find information on adjusting the rinse aid dosage in the "Rinse aid"
section of this booklet.
The door opens automatically during the drying phase.
Do not close the door until the drying test has finished.
Upper basket level:
Position: Bottom
Jumbo cup rack
(if available):
ECO
Outer position
Loading examples
Pictures illustrating how to load the dishwasher are shown on the following pages.
Picture : Upper basket
Picture : Lower basket
Picture : Cutlery tray
Do not lower or remove the basket inserts.
Remove the bottle holder from the lower basket
(if available).
46
Page 47
Capacity
15
Comparison tests
47
Page 48
Comparison tests
48
Page 49
Operation
Detergent
Only use detergents formulated
for domestic dishwashers. Do not
use washing-up liquid.
Active ingredients
Modern detergents contain various
active ingredients, the most important
of which are:
– Complexing agents to prevent
calcification.
– Alkalis to aid the removal of dried on
soiling.
– Enzymes to break down starch and
loosen protein.
– Oxygen based bleaching agents to
remove coloured stains (e.g. tea,
coffee, tomato sauce).
Most dishwasher detergents are mildly
alkaline and contain enzymes and
oxygen based bleaching agents.
You can also buy combination products
(see "Programme options DetergentAgent", if applicable).
In addition to detergent, these products
contain rinse aid and salt substitutes.
They are available as "3 in 1" or when
they also contain other components
such as glass and stainless steel
protective additives and enhanced
cleaning power, as "5 in 1", "7 in 1", "All
in 1" etc.
Refer to the manufacturer's packaging
as to whether combination products are
suitable for the water hardness level in
your area.
Please note that the cleaning and
drying results of combination
detergents can vary greatly.
For optimum cleaning and drying
results, use Miele dishwasher
detergent and add Miele salt and
Miele rinse aid separately. See
"Optional accessories".
Types of detergent:
– Powder and liquid gel detergents.
These detergents allow you to adjust
the amount dispensed according to
the amount of load and level of
soiling.
– Tab detergents. These are suitable for
most levels of soiling.
49
Page 50
Operation
Detergent dosage
Follow the dosage recommended by
the manufacturer on the packaging.
Unless directed otherwise, use one
detergent tab or add 20 to 30ml
detergent to compartmentII,
depending on the level of soiling.
With very heavy soiling you can also
add a small amount of detergent to
compartmentl.
Tabs may not dissolve completely
when the "QuickPowerWash"
programme (if available) is used.
Failure to dispense the
recommended amount of detergent
may impair cleaning results.
Dishwasher detergents contain
irritant or corrosive ingredients which
can cause burning in the nose,
mouth and throat if swallowed, or
inhibit breathing.
Avoid inhalation of powder
detergents and do not ingest
dishwasher detergent. Seek medical
advice immediately if detergent has
been swallowed or inhaled.
Keep detergent and other household
agents out of the reach of children at
all times. Keep children away from
the dishwasher when the door is
open. There could still be detergent
residues in the cabinet. To avoid the
danger of children coming into
contact with the dishwasher
detergent, only add detergent just
before starting the programme and
close the door, activating the safety
lock (if your dishwasher is fitted with
one).
50
Page 51
Adding detergent
Press the opening catch on the
detergent dispenser. The flap will
spring open.
The flap is always open at the end of a
programme.
Operation
Add the required amount of detergent
and close the flap.
Make sure that the detergent
packaging is properly closed after
use to avoid it getting damp and
becoming lumpy.
For information
Compartment I holds max. 10 ml,
Compartment II holds max. 50 ml.
There are marks in Compartment II to
assist with dispensing: 20, 30. The
marks indicate a level of approx. 20 or
30 ml when the door is open in a
horizontal position.
51
Page 52
Operation
Switching on
Turn on the tap if it is turned off.
Open the door.
Make sure the spray arms are not
obstructed.
Press the button for at least
2seconds.
The programme selected will appear
briefly in the display and the
appropriate indicator light will come on.
Then, if applicable, the estimated
energy and water consumption for the
programme selected will appear for a
few seconds.
Finally, the display will show the
estimated programme duration for the
programme selected.
Selecting a programme
Choose your programme according to
the type of load and how dirty it is.
The different programmes and their
uses are described in the Programme
chart later on in this booklet.
Use the programme selector button
to select the programme required.
The indicator light next to the selected
programme will come on.
Further programmes are selected via
the Further option.
Use the programme selector button
to select the Further option.
The first of the further programmes will
appear in the display.
Use the arrow buttons to select
the programme required.
During the course of the programme
you can use OK to display the name of
the programme which is currently
running.
52
You can now select programme options
(see "Programme options").
If any programme options are selected,
the appropriate indicator lights will also
light up.
Page 53
Operation
Starting the programme
Start the programme by closing the
door.
The programme will begin.
The In-operation indicator comes on to
show that a programme has been
started.
A programme should only be
cancelled in the first few minutes, if
at all. Otherwise important
programme stages could be omitted.
Time display
The estimated duration of the
programme selected appears in hours
and minutes in the display before the
programme begins. If the door is
opened during the programme, the time
left until the end of the programme is
displayed.
Each programme stage is indicated by
a symbol:
Pre-wash / Soak
Main wash
Interim rinse
Final rinse
Drying
Finish
The programme duration displayed may
vary with the same programme. It is
influenced by, among other things, the
water temperature at each intake, the
reactivation process, the water softener,
the type of detergent, the amount of
crockery and how dirty it is.
When a programme is selected for the
first time, the display will show the
average programme duration for a cold
water intake.
The times shown in the Programme
chart refer to standard test loads and
temperatures.
Each time a programme is run, the
electronic unit takes the new conditions
into account, and calculates the time
required.
53
Page 54
Operation
Energy management
To save energy, the dishwasher will
switch off automatically 10 minutes
after the last time a button has been
pressed or after the end of the
programme (see "Settings menu Optimise standby").
Press the button to switch the
dishwasher back on.
The dishwasher will not switch off
whilst a programme or the FlexiTimer
is running or if there is a fault.
At the end of the programme
At the end of a programme, the Inoperation indicator light will be visible
flashing slowly with the door shut. The
buzzer might also be sounding.
The In-operation indicator light will go
out 10minutes after the end of the
programme if the door is closed.
The programme has finished when the
door has opened slightly (if applicable)
and Finished appears in the display.
Open the door fully so that the door
catch rail retracts again.
You can now empty the dishwasher.
If you have deactivated the
automatic door opening function (see
"Settings menu - AutoOpen"), but
would still like to open the door at
the end of the programme, then
make sure that you open the door
fully.
Otherwise steam from the
dishwasher could damage the edge
of the worktop because the fan is no
longer running.
In the QuickPowerWash programme the
door will not open until a few minutes
after the programme has finished.
If the Consumption programmable
function is switched on, you can now
call up the actual energy and water
consumption of the programme which
has just finished (see "Caring for the
environment - EcoFeedback
consumption indicator").
The drying fan may continue to run for
a few minutes at the end of the
programme.
54
Page 55
Operation
Switching off
At the end of a programme:
Open the door.
The dishwasher can be switched off
at any time using the button.
Switching the dishwasher off during a
programme cancels the programme.
Switching the dishwasher off during the
run-up to a Delay start time (FlexiTimer)
will also stop the process.
If the dishwasher is not going to be
used for a longer period of time, e.g.
whilst on holiday, the tap should be
turned off.
Unloading the dishwasher
Dishes tend to break and chip more
easily when they are hot. Allow the
dishes to cool until they are comfortable
enough to handle before unloading
them.
If you open the door fully after switching
off, the dishes will cool much faster.
First unload the lower basket, then the
upper basket and finally the cutlery tray
(depending on model).
This will prevent water drops from the
upper basket and cutlery tray from
falling onto the dishes in the lower
basket.
55
Page 56
Operation
Interrupting a programme
A programme is interrupted as soon as
the door is opened.
If the door is closed again, the
programme will continue from the point
it was at before the door was opened.
Water in the dishwasher may be
hot. Danger of scalding!
Only open the door if absolutely
necessary and exercise extreme
caution when doing so. Before
closing the door again, leave it ajar
for approx. 20 seconds. This will
enable the temperature in the wash
cabinet to settle. Then raise the door
up and push until the catch engages.
Changing a programme
If the detergent dispenser flap has
already opened, do not change the
programme.
If a programme has already started and
you wish to change it, proceed as
follows:
Open the door.
Switch the dishwasher off with the
button.
Switch the dishwasher on again with
the button.
Select the programme you want, and
then start it by shutting the door.
The In-operation indicator comes on to
show that a programme has been
started.
56
Page 57
Programme options
Options
You can select and deselect the options
before starting the programme using
the appropriate buttons and the display.
Open the door.
Switch the dishwasher on with the
button.
The indicator light next to the
programme selected will come on.
Select a programme.
Press the button for the option you
want.
The indicator light for the relevant
button will come on if the option is
available for the programme selected.
If the option is not compatible with the
programme selected, a message to this
effect will appear in the display.
In this instance, confirm the message
with OK.
Short
The Short option reduces the duration
of programmes in which this option is
available by up to 30% (see
"Programme chart").
In order to achieve optimum cleaning
results, energy consumption may
increase slightly with this option.
When used in combination with the
QuickPowerWash programme, the
Short option results in a wash
programme without drying or automatic
opening of the door (if available).
Energy save
The Energy save option reduces the
energy consumption of programmes in
which this option is available by up to
20%.
In order to achieve optimum cleaning
results, the programme duration is
extended with this option.
Start the programme by closing the
door.
The option selected will remain active
for that particular programme until the
setting is changed.
57
Page 58
Programme options
FlexiTimer with EcoStart
The FlexiTimer gives you three ways
of starting the programme by means of
delaying the start. You can set the start
time or the finish time of a programme.
You also have the option of taking
advantage of time variable economy
rates of electricity using the EcoStart
function.
When using the Delay start function,
make sure that the detergent
compartment is dry before adding
detergent. Wipe dry with a cloth if
necessary. If the compartment is
wet, powder detergent can become
lumpy and stick to the dispenser,
with the result that it is not fully
dispensed.
Do not use liquid detergent when
selecting Delay start, as it can run
into the dishwasher before it is
required.
Open the door.
Switch the dishwasher on with the
button.
Select the programme you want.
Press the button.
The indicator light comes on.
You can use the arrow buttons to
select the Start at, Finish at, or EcoStart
function or Back .
Confirm selection of the function you
want with OK.
The set time will appear and the hour
number block will be highlighted.
You can now enter the time you want
using the arrow buttons and
confirm with OK.
If, while you are setting the time, you do
not press any buttons for several
seconds, the display will revert to the
previous menu. You will then have to
enter your settings again.
58
Page 59
Programme options
Start at
With the Start at function, you set the
exact time at which you want the
programme to start.
Use the arrow buttons to set the
hour and confirm with OK.
The hours will be saved and the minute
number block will be highlighted.
Use the arrow buttons to set the
minutes and confirm with OK.
The saved start time for the programme
selected will appear in the display.
The indicator light will come on.
Close the door.
When the set time is reached, the
programme selected will begin
automatically.
Finish at
With the Finish at function, you set the
time at which you wish the programme
to end.
Use the arrow buttons to set the
hour and confirm with OK.
The hours will be saved and the minute
number block will be highlighted.
Use the arrow buttons to set the
minutes and confirm with OK.
The estimated start time for the
programme selected will appear in the
display.
The indicator light will come on.
Close the door.
A message will appear in the display if
the programme cannot be completed
by the set finish time because it has too
long a running time.
The programme will start automatically
when the estimated start time is
reached.
59
Page 60
Programme options
EcoStart
The EcoStart function allows you to take
advantage of time variable economy
rates of electricity. Before you can use
this option, you must set up to three
electricity tariff time zones (see
"Settings - EcoStart").
You then set the latest time at which the
programme selected should end.
The dishwasher will start automatically
in the cheapest tariff zone within the
time set.
Use the arrow buttons to set the
hour and confirm with OK.
The hours will be saved and the minute
number block will be highlighted.
Use the arrow buttons to set the
minutes and confirm with OK.
The estimated start time for the
programme selected will appear in the
display.
The indicator light will come on.
Close the door.
Changing or deleting set times
You can change the set times or the
programme before the start time in the
display is reached.
Open the door.
Press the button.
Use the arrow buttons to select
the setting you want to change and
confirm with OK.
Use the arrow buttons to select
the Change or Delete function and
confirm with OK.
After confirming the Change function,
you can change the set time.
After confirming the Delete function, the
programme duration will appear in the
display for the selected programme.
The indicator light will go out and the
indicator light for the selected
programme will come on.
Start the programme by closing the
door.
The selected programme will start
automatically during the most cost
effective time zone. It will finish at the
latest by the set finish time.
60
Page 61
DetergentAgent
For optimum cleaning results, the
dishwasher automatically adjusts the
programme sequence to the type of
detergent being used. Depending on
the programme, this can mean that the
running time and energy consumption
vary slightly.
If you only ever use multi-function
combination products containing salt
and rinse aid in your dishwasher, you
can switch the reminders off if you wish
(see "Settings menu - Refill reminders").
The DetergentAgent function will not be
affected by this.
Ensure that you refill dishwasher salt
and rinse aid and switch on the refill
reminders again if you are not using
combination products.
Programme options
61
Page 62
Programme chart
Programme Programme sequence
Pre-wash Main wash Interim rinse Final rinse Drying
°C °C
1)
ECO
Automatic Variable programme sequence,
Intensive
75°C
QuickPower
Wash
Gentle X 45 X 58 X
Light soiling
55°C
ExtraQuiet 46 X 60 X
SolarSave 2X X X X X
Maintenance
programme
X 48 X 34 X
sensor-controlled adjustment according to amount of crockery and soiling
If
required
2X 75 X 58 X
X 55 X 58 X
45-65 If
required
65 X 65 X
75 2X 70 X
57-70 X
1)
This programme is the most efficient in terms of its combined energy and water
consumption for cleaning normally soiled crockery.
62
Page 63
Programme chart
Consumption
2)
Duration
2)
Electricity Water
Cold water Hot water Litres Cold water Hot water
15°C 55°C 15°C 55°C
kWh kWh h:min h:min
0.53 3) / 0.54
0.75 5) -1.10
4)
0.32 3) / 0.34
6)
0.50 5) -0.65
4)
11.4 3) / 11.1
6)
6.5 5) -15.0
4)
6)
2:49 2:41
1:54-2:52 1:37-2:47
1.35 0.90 14.5 2:59 2:49
1.30 0.80 11.5 0:58 0:58
0.95 0.45 13.5 2:06 1:51
1.05 0.60 13.5 2:17 2:03
1.00 0.70 9.5 4:20 4:11
0.06 27.0 2:30
2.05 1.25 22.0 2:11 1:47
2)
In practice there may be variations to these figures due to variable conditions and data
recorded by the sensors. The durations displayed in your dishwasher will reflect your
household conditions.
Selecting programme options will also affect consumption levels and programme
durations (see "Programme options").
3)
Standard height dishwashers
4)
XXL dishwashers
5)
Part load with light soiling
6)
Full load with heavy soiling
63
Page 64
Programme chart
Mixed crockery
Pots, pans, everyday porcelain
and cutlery
Normal food deposits which
have begun to dry on
Burnt-on, stubborn, dried-
on food deposits containing
starch or protein
1)
Water and
energy saving programme
Shorter duration
Average programme values
Shorter duration
Maximum cleaning power
Shorter duration
1)
Food such as potatoes, pasta, rice or stews can leave starchy deposits. Deposits containing protein
can be left by food such as meat, fish or eggs and bakes.
Crockery Food deposits Programme
features
Mixed,
everyday crockery
Heat-sensitive glasses and
plastic
All fresh to dried-on food
deposits
Fresh, easily removed food
deposits
Variable, sensor-controlled
programme sequence
Shorter duration
Short programme with
duration less than 1 hour
3)
Gentle programme with
glass care
Shorter duration
No crockery
Residual salt after refilling the
salt container
Flushes out salt residues
Fresh food deposits which
have begun to dry on
64
Page 65
Programme chart
-
25 ml
or
1 tab
Automatic
+short
- 1 tab
3)
QuickPowerWash
-
20 ml
or
1 tab
Gentle
+short
-
25 ml
or
1 tab
ECO
+short
-
25 ml
or
1 tab
Light soiling 55°C
4)
+short
10 ml
25 ml
or
1 tab
Intensive 75°C
+short
Detergent
Compartment I
2)
Compartment II
2)
Programme
- -
QuickPowerWash
+short
2)
see "Detergent"
3)
best cleaning results are only achieved with Miele's quick dissolving UltraTab Multi
4)
in "Further " (depending on model)
65
Page 66
Programme chart
Further programmes
ExtraQuiet
Very quiet programme with a longer
duration. Suitable for mixed loads of
crockery, pots and pans with moderate,
slightly dried on food residues.
SolarSave
This programme does not heat the
water. To use it, the water intake
temperature must be at least 45°C (see
"Water connection - Connection to the
water supply"). This programme is
suitable for mixed loads of crockery and
glassware with moderate, slightly dried
on food residues.
Maintenance programme
The wash cabinet is largely selfcleaning. However, if residues or soiling
build up in the cabinet, they can be
removed by running the "Maintenance
programme" without a load. This
programme is designed for cleaning the
wash cabinet using care products such
as Miele's dishwasher cleaner or
conditioner (see "Optional accessories Dishwasher care products). Please
follow usage instructions on the
packaging.
66
Page 67
Cleaning and care
Check your dishwasher regularly
(approx. every 4-6 months). This way
faults and problems can be avoided.
The external surfaces of this
appliance are all susceptible to
scratching.
Contact with unsuitable cleaning
agents can alter or discolour the
external surfaces.
Cleaning the wash cabinet
The wash cabinet is largely selfcleaning, provided that the correct
amount of detergent is always used.
If there are nevertheless limescale or
grease deposits in the cabinet, these
can be removed with the Original Miele
dishwasher conditioning agent
(available from Miele or at www.mieleshop.com). Follow the dosage
recommended by the manufacturer on
the packaging.
Using mainly low temperature
programmes (below 50°C), could cause
bacteria and unpleasant odours to build
up in the wash cabinet. To avoid this,
the dishwasher will increase the
temperature in the final rinse of the
selected programme automatically after
several programmes using low
temperatures have been run.
Cleaning the door and the door seal
Mould could build up on the door seal
and the sides of the dishwasher door as
these surfaces are outside the wash
cabinet and are not accessed and
cleaned by the spray arm jets.
Wipe the door seals regularly with a
damp cloth to remove food deposits.
Wipe off any food or drink residues
which may have dripped onto the
sides of the dishwasher door before
closing it.
Cleaning the control panel
The control panel should only be
wiped with a damp cloth.
Cleaning the reflector panel
The reflector panel for the In-operation
indicator light is situated in the
coverplate underneath the worktop.
The reflector panel should only be
wiped with a damp cloth or a suitable
cleaning agent designed for use on
plastic.
Clean the filters in the wash cabinet
regularly.
67
Page 68
Cleaning and care
Cleaning the door front
Soiling that is left too long might
become impossible to remove and
could cause external surfaces to alter
or discolour.
Remove any soiling immediately.
Clean the front with a solution of
warm water and a little washing-up
liquid applied with a soft sponge.
Wipe the surfaces dry using a soft
cloth.
For cleaning, you can also use a
clean, damp microfibre cloth, such as
the Original Miele all purpose
microfibre cloth, without any cleaning
agent.
To avoid damaging external surfaces,
do not use:
– cleaning agents containing soda,
ammonia, acids or chlorides,
– cleaning agents containing descaling
agents,
– abrasive cleaning agents, e.g.
powder cleaners and cream cleaners,
– solvent-based cleaning agents,
– stainless steel cleaning agents,
– dishwasher cleaner,
– oven cleaner,
– glass cleaning agents,
– hard, abrasive brushes or sponges,
e.g. pot scourers, brushes or
sponges which have been previously
used with abrasive cleaning agents,
– dirt erasers,
– sharp metal scrapers,
68
– steel wool or metal scourers,
– steam cleaning appliances.
Page 69
Cleaning and care
Checking the filters in the wash cabinet
The filter combination in the base of the
wash cabinet retains coarse soil from
the suds solution, preventing it
accessing the circulation system and
re-entering the cabinet through the
spray arms.
This dishwasher must not be
used without all the filters in place.
Collection of coarse soil may cause the
filters to clog. The level of soiling and
time it takes before the filters need
cleaning will vary depending on use.
The message Check filters will appear in
the display after every 50 programme
cycles (factory default setting).
You can set the interval for this
message to appear to between 30 and
60 programme cycles (see "Settings
menu - Check filters").
Cleaning the filters
Switch the dishwasher off.
Turn the handle anti-clockwise to
release the filter combination .
Lift the filter combination out of the
dishwasher . Remove any coarse
particles and rinse the filter well
under running water.
Use a nylon brush if necessary.
Check the filter combination.
Clean it if necessary.
Then confirm the message with OK.
The message will go out.
During cleaning ensure that
course soil doesn't get into the
circulation system and cause a
blockage.
69
Page 70
Cleaning and care
To clean the inside of the filter, the flap
must be opened:
Press the catches together in the
direction of the arrows as shown, and
open the filter .
Rinse all the filters under running
water.
Then close the flap so that the catch
engages.
Replace the filter combination so that
it lies flat in the base of the wash
cabinet.
Then turn the handle clockwise until
both arrows point towards each
other. This will lock the filter
combination in place.
Take care when you are fitting
the filter combination that it is
secured in position correctly.
Otherwise coarse soil could get into
the circulation system and cause a
blockage.
70
Page 71
Cleaning the spray arms
Particles of food can get stuck in the
spray arm jets and bearings. The spray
arms should therefore be inspected and
cleaned regularly (approx. every 4 - 6
months).
Switch the dishwasher off.
Remove the spray arms as follows:
Take out the cutlery tray (if your
dishwasher is fitted with one).
Push the top spray arm upwards to
engage the inner ratchet. Then
unscrew the spray arm.
Cleaning and care
Pull the lower spray arm firmly
upwards to remove it.
Push the middle spray arm upwards
to engage the ratchet. Then
unscrew the spray arm .
Remove the lower basket.
Use a pointed object to push food
particles into the spray arm jets.
Rinse thoroughly under running
water.
Refit the spray arms and check that
they rotate freely.
71
Page 72
Problem solving guide
With the help of the following guide, minor faults in the performance of the
appliance, some of which may result from incorrect operation, can be put right
without contacting Miele. This will save time and money.
Please note that a call-out charge will be applied to unnecessary service visits
where the problem could have been rectified as described in these operating
instructions.
Unauthorised or incorrect repairs could cause personal injury or damage to
the appliance.
Repair work to electrical appliances must only be carried out by a suitably
qualified and competent person in strict accordance with current local and
national safety regulations. The manufacturer cannot be held liable for
unauthorised work.
Technical problems
Problem Possible cause and remedy
The dishwasher does
not start.
The dishwasher stops
during a programme.
After the programme
has started, the Inoperation indicator light
is not visible.
The door is not properly closed.
Push the door firmly shut.
The appliance is not plugged in.
Insert the plug and switch on at the socket.
The mains fuse has tripped.
Reset or replace the fuse (see data plate for
minimum fuse rating).
The appliance is not switched on.
Switch the dishwasher on with the button.
The mains fuse has tripped.
Reset or replace the fuse (see data plate for
minimum fuse rating).
If the mains fuse trips again, call Miele.
The reflector panel was not correctly fitted.
Refit the reflector panel correctly (see Installation
diagram).
72
Page 73
Problem solving guide
Problem Possible cause and remedy
The buzzer is sounding.
The programme will not
start.
The In-operation
indicator is not lit up.
The door has not closed properly, because it had not
been fully opened after the door had been opened
automatically.
Open the door fully so that the door catch rail
retracts again.
Then close the door.
73
Page 74
Problem solving guide
Problem Possible cause and remedy
The In-operation
indicator light is
flashing quickly.
The buzzer is sounding.
One of the following
faults appears in the
display:
Fault FXX There may be a technical fault.
Waterproof The Waterproof system has reacted.
Fault F78 A fault has occurred in the circulation pump.
Before rectifying the problem, you must:
Switch the dishwasher off with the button.
After a few seconds:
Switch the dishwasher back on.
Select the programme you want.
Close the door.
If the fault message appears again, there is a
technical fault.
Call Miele.
Turn off the tap.
Call Miele.
Switch the dishwasher off for at least 30 seconds
with the button.
Switch the dishwasher back on.
Select the programme you want.
Close the door.
If the fault message appears again, there is a
technical fault.
Call Miele.
74
Page 75
Problem solving guide
Water inlet fault
Problem Possible cause and remedy
The In-operation
indicator is flashing
quickly.
The buzzer is sounding.
One of the following
faults appears in the
display:
Open stopcock The tap is turned off.
Turn on the tap fully.
Water intake Before rectifying the problem, you must:
Switch the dishwasher off with the button.
Water intake is restricted.
Turn on the tap fully and start the programme
again.
Clean the water inlet filter (see "Maintenance").
The water pressure at the intake is lower than 50
kPa (0.5 bar).
Seek professional advice.
The following message
appears in the display
during the SolarSave
programme:
Intake temp. low
The intake water has not reached the required
temperature of 45°C (see "Water connection Connection to the water supply").
Start the programme again.
If the fault message appears again, select a
different programme.
75
Page 76
Problem solving guide
Water drainage fault
Problem Possible cause and remedy
The In-operation
indicator light is
flashing quickly.
The buzzer is sounding.
The following fault
appears in the display:
Drain
Before rectifying the problem, you must:
Switch the dishwasher off with the button.
The water outlet is restricted.
There might be water in the wash cabinet.
Clean the filter combination (see "Cleaning and
care - Cleaning the filters").
Clean the drain pump (see "Maintenance").
Clean the non-return valve (see "Maintenance").
Remove any kink or loop in the drain hose.
76
Page 77
Problem solving guide
General problems
Problem Possible cause and remedy
Detergent residue is left
in the dispenser at the
end of a programme.
The detergent
dispenser lid cannot be
closed properly.
At the end of a
programme there is a
film of moisture on the
inside of the door and
the interior walls.
Water remains in the
wash cabinet at the end
of a programme.
The dispenser was still damp when detergent was
added.
Make sure the dispenser is dry before adding
detergent.
Clogged detergent residue is blocking the catch.
Clean the detergent from the catch.
This is caused by the drying system and does not
indicate a fault. The moisture will dissipate after a
while.
Before rectifying the problem you must:
Switch the dishwasher off with the button.
The filter combination in the wash cabinet is clogged.
Clean the filter combination (see "Cleaning and
care - Cleaning the filters").
The drain pump or non-return valve may be blocked.
Clean the drain pump or the non-return valve (see
"Maintenance").
The drain hose is kinked.
Remove any kink from the drain hose.
77
Page 78
Problem solving guide
Noises
Problem Possible cause and remedy
Knocking noise in the
wash cabinet.
Rattling noise in the
wash cabinet.
Knocking noise in the
water pipes.
A spray arm is knocking against an item in a basket.
Interrupt the programme, and rearrange the items
which are obstructing the spray arm.
Items of crockery are insecure in the wash cabinet.
Interrupt the programme, and rearrange the items
of crockery.
A foreign object (e.g. a cherry stone) has become
lodged in the drain pump.
Remove the foreign object from the drain pump
(see "Maintenance - Cleaning the drain pump and
non-return valve").
This may be caused by the on-site installation or the
cross-section of the piping.
This has no influence on dishwasher function. If in
doubt, contact a suitably qualified plumber.
78
Page 79
Problem solving guide
Unsatisfactory washing result
Problem Possible cause and remedy
The dishes are not
clean.
Smearing appears on
glassware and cutlery,
there is a bluish sheen
on the surface of
glassware; film can be
wiped off.
The dishes were not loaded correctly.
See notes in "Loading the dishwasher".
The programme was not powerful enough.
Select a more intensive programme (see
"Programme chart").
There is some stubborn soiling although most of the
crockery is only lightly soiled (e.g. with tea stains).
Use the Automatic programme option (see
"Settings menu - Automatic").
Not enough detergent was dispensed.
Use more detergent, or change your detergent.
Items are blocking the path of the spray arms.
Rearrange the items so that the spray arms can
rotate freely.
The filter combination in the base of the wash cabinet
is not clean or is not correctly fitted. This may cause
the spray arm jets to get blocked.
Clean and/or fit the filter combination correctly.
Clean the spray arm jets if necessary (see
"Cleaning and care - Cleaning the spray arms").
The non-return valve is open and blocked. Dirty water
has flowed back into the wash cabinet.
Clean the drain pump and the non-return valve
(see "Maintenance").
The rinse aid dosage is set too high.
Reduce the dosage (see "Settings menu - Rinse
aid").
79
Page 80
Problem solving guide
Problem Possible cause and remedy
Dishes, cutlery and
glasses are not dry or
are flecked.
Glassware has a brown
or blue tinge, and film
cannot be wiped off.
Glassware is dull and
discoloured; film cannot
be wiped off.
Tea or lipstick stains
have not been
completely removed.
Plastic items are
discoloured.
The amount of rinse aid may be insufficient, or the
rinse aid reservoir is empty.
Replenish the reservoir, increase the dosage or
change the brand of rinse aid (see "Before using
for the first time - Rinse aid").
Crockery was taken out of the cabinet too soon.
Leave it in for longer (see "Operation").
Combination tabs have been used which have
impaired drying performance.
Change your detergent, or replenish the rinse aid
(see "Before using for the first time - Rinse aid").
This may be caused by the detergent.
Change your detergent.
The glassware is not dishwasher-proof. The surfaces
are affected.
There is no remedy.
Purchase glassware which is dishwasher-proof.
The wash temperature of the selected programme
was too low.
Select a programme with a higher wash
temperature.
The bleaching effect of the detergent used is too low.
Change your detergent.
Natural dyes e.g. from carrots, tomatoes or tomato
sauce may be the cause. The amount of detergent
used or its bleaching effect was not sufficient to deal
with natural dyes.
Use more detergent (see "Operation - Detergent").
Discolouration is irreversible.
80
Page 81
Problem solving guide
Problem Possible cause and remedy
White residue is visible
on cutlery and crockery,
clouding occurs on
glassware; film can be
wiped off.
There are rust stains on
cutlery.
Not enough rinse aid was used.
Increase the dosage (see "Settings menu - Rinse
aid").
There is no salt in the salt reservoir.
Fill the salt reservoir (see "Before using for the first
time - Dishwasher salt").
The salt reservoir cap has not been screwed on
correctly.
Replace it, making sure that it screws back on
correctly.
An unsuitable combination detergent has been used.
Change your detergent. Use a standard liquid,
tablet or powder detergent, and fill the salt and
rinse aid reservoirs in the dishwasher.
The water softener is programmed to too low a water
hardness level.
Programme the water softener to a higher water
hardness level (see "Settings menu - Water
hardness").
The affected items are not corrosion resistant.
There is no remedy.
Purchase cutlery which is dishwasher-proof.
A programme was not run after dishwasher salt was
added. Traces of salt have got into the wash cycle.
Always run the QuickPowerWash programme with
the Shortprogramme option selected and without
any crockery in the dishwasher after adding
dishwasher salt.
The salt reservoir cap has not been screwed on
correctly.
Replace it, making sure that it screws back on
correctly.
81
Page 82
Maintenance
Cleaning the water inlet filter
A filter is incorporated in the screw
connection of the valve on the water
inlet hose. The filter must be cleaned
when dirty, otherwise insufficient water
flows into the wash cabinet.
The plastic housing of the water
connection contains an electrical
component.
The housing must not be dipped in
water.
Recommendation
If the mains water contains a large
amount of insoluble substances, we
recommend fitting a large-area filter in
the connection between the tap and the
water inlet hose threaded union. This
filter is available from Miele.
Cleaning the filter:
Disconnect the dishwasher from the
mains supply.
Switch off at the mains socket and
withdraw the plug.
Turn off the tap.
Unscrew the inlet hose.
Carefully remove the washer.
Withdraw the filter using pointed
pliers and rinse clean under running
water.
Replace the filter and washer, making
sure they are sitting correctly.
Reconnect the inlet hose to the tap,
making sure it goes on correctly and
is not cross-threaded.
Turn on the tap.
If water leaks out, the inlet hose may
not be connected securely or it may
have been screwed on at an angle.
Unscrew and reconnect the inlet hose
correctly.
82
Page 83
Cleaning the drain pump and non-return valve
If the water has not been pumped away
at the end of a programme, the drain
pump or the non-return valve might be
blocked. They are, however, easy to
clean.
Disconnect the dishwasher from the
mains supply. Switch off at the mains
socket and withdraw the plug.
Take the filter combination out of the
wash cabinet (see "Cleaning and care
- Cleaning the filters").
Scoop the water out of the cabinet
using a suitable container or utensil.
Maintenance
The drain pump is situated under the
non-return valve (see arrow).
Remove all foreign objects from the
drain pump (watch out for glass or
bone splinters which are particularly
difficult to detect and could cause
injury). Turn the drain pump impeller
by hand to check that there are no
more obstructions. You will feel a little
resistance when you turn the impeller.
Press the catch for the non-return
valve inwards .
Tilt the non-return valve inwards until
it is released.
Rinse it thoroughly under running
water and remove any soiling from
the non-return valve.
Carefully refit the non-return valve
and secure it with the catch.
Ensure that the catch engages
correctly.
Be careful not to damage any
delicate components when cleaning
the drain pump and the non-return
valve.
83
Page 84
After sales service
Repairs
In the event of any faults which you
cannot remedy yourself, please contact
Miele.
The contact details for Miele are
given at the back of these
instructions.
When contacting Miele, please quote
the model and serial number of your
dishwasher, both of which are shown
on the data plate on the right-hand side
of the door.
Warranty
The manufacturer's warranty for this
appliance is 2 years.
For further information, please refer to
your warranty booklet.
84
Page 85
Optional accessories
Dishwasher detergent and rinse aid, as
well as cleaning and care products, are
available as optional accessories.
All the products are designed for use
with Miele dishwashers.
These and many other useful products
can be ordered from Miele or via the
Miele Webshop (see end of this booklet
for contact details).
Dishwasher detergent, rinse aid and salt
When you decided to buy a Miele
dishwasher, you chose excellent quality
and performance. Ensuring that your
dishwasher always delivers the best
possible results will also depend on
your choice of dishwasher detergent,
rinse aid and dishwasher salt, as
cleaning results can vary depending on
the brand used.
With Miele cleaning products and
detergents, you can be sure of optimum
results as these products have been
specially designed for Miele
dishwashers.
Detergent tabs
– sparkling results even with stubborn
food deposits
– combination product with other
components such as rinse aid, salt
and glass protection additives
– phosphate-free - safe for the
environment
– water-soluble wrapping - no need to
unwrap
Powder detergent
– with active oxygen for thorough
cleaning
– with enzymes which are effective
even in low temperature programmes
– with glass protection against
corrosion
Rinse aid
– for gleaming glasses
– helps crockery to dry
– with glass protection against
corrosion
– specially designed cap for precise,
easy dispensing
Dishwasher salt
– prevents limescale on crockery and
in the appliance
– extra coarse-grained
85
Page 86
Optional accessories
Dishwasher care products
Miele cleaning and care products
provide optimum care for your
dishwasher.
Dishwasher cleaner
– cleans the dishwasher effectively and
thoroughly
– removes grease, bacteria and
unpleasant odours
– ensures excellent dishwashing results
Dishwasher descaler
– removes heavy limescale deposits
– mild and gentle with natural citric
acid
Dishwasher conditioner
– removes odours, limescale and light
deposits
– maintains the elasticity and leak
tightness of the seals
Dishwasher freshener
– neutralises unpleasant odours
– fresh, pleasant lime and green tea
scent
– easy to attach to the dishwasher
basket
– very economical, lasts for 60 wash
cycles
86
Page 87
Electrical connection
This dishwasher is supplied with a
mains cable with moulded plug ready
for connection to an AC single phase
supply, (230 - 240 V 50 Hz for NZ and
Australia) via a suitable switched
socket.
The electrical socket must be
easily accessible after the
dishwasher has been installed. Do
not connect the dishwasher to the
mains electricity supply by an
extension lead. Extension leads do
not guarantee the required safety of
the appliance (e.g. danger of
overheating).
Do not connect the appliance solely to
an inverter such as those used with an
autonomous energy source e.g. solar
power. When switched on, peak loads
in the system can cause the safety
switch-off mechanism to be triggered.
This can damage the electronic unit.
The machine must not be used with socalled energy-saving devices either.
These reduce the amount of energy
supplied to the machine, causing it to
overheat.
Before connecting the appliance,
check that the connection data on
the data plate (voltage, frequency,
rated load and fuse rating) matches
the mains electricity supply. If in any
doubt, consult a qualified electrician.
The data plate is located on the righthand side of the door.
All electrical work must be
carried out by a suitably qualified
and competent person in strict
accordance with current local and
national safety regulations.
For extra safety, it is advisable to
install a residual current device
(RCD), with a trip current of 30mA.
87
Page 88
Water connection
The Miele Waterproof system
As long as your dishwasher has been
installed correctly, the Miele waterproof
anti-leak system will protect you from
water damage.
Connection to the water supply
Water in the dishwasher must
not be used as drinking water.
– The dishwasher may be connected to
a cold or hot water supply, max.
60°C.
We would only recommend
connection to a hot water supply if it
is economical, e.g. a solar powered
supply. When connected to a hot
water supply, all programmes will be
carried out with hot water.
– The SolarSave programme (if
available) requires a hot water supply
of between 45°C (minimum) and
60°C (maximum).
The higher the water intake
temperature, the better the cleaning
and drying results.
88
Page 89
Water connection
– The inlet hose is approx. 1.5m long.
– A tap with a 3/4" male thread must
be provided on site.
– IMPORTANT: Australia and New
Zealand
This appliance must be installed
according to AS/NZS 3500.1. Back
flow prevention is already integrated
in the appliance.
– The water pressure (flow pressure at
the take-off point) must be between
50 and 1000 kPa (0.5 and 10 bar). If
the water pressure is lower than this,
the fault message Water intake will
appear in the display (see "Problem
solving guide"). If the water pressure
is too high, a pressure reducer valve
must be fitted.
After connecting the dishwasher to
the water supply, check that all
plumbing connections are watertight.
To avoid any damage to the
appliance, the dishwasher must only
be operated when it is connected to
a fully vented plumbing system.
The inlet hose must not be
shortened or damaged in any way as
it contains electrical components
(see illustration).
89
Page 90
Water connection
Drainage
– The appliance drainage system is
fitted with a non-return valve which
prevents dirty water from flowing
back into the dishwasher via the
drain hose.
– The dishwasher is supplied with
approx. 1.5 m of flexible drain hose
with an internal diameter of 22 mm.
– The drain hose can be extended
using a connection piece to attach a
further length of hose. The drainage
length must not be longer than 4 m,
and the delivery head must not
exceed 1 m.
– If the hose is to be directly fitted to
the drainage outlet on site, use the
hose clip supplied (see installation
diagram).
– The hose can be directed to the left
or the right of the appliance.
– The on-site connector for the drain
hose can be adapted to different
widths of hose. If the connector
protrudes too far into the drain hose,
it will need to be shortened.
Otherwise the drain hose may
become blocked.
Venting the drainage system
If the on-site drain connection is
situated lower than the guide path for
the bottom basket rollers in the open
door, the drainage system must be
vented. Otherwise a siphoning effect
during a programme can cause the
appliance to empty itself of water.
To vent it: Open the dishwasher door
fully.
Pull the lower spray arm firmly
upwards to remove it.
Cut off the top of the vent valve in the
wash cabinet.
– The drain hose must not be
shortened.
Make sure that there are no kinks
in the hose, and that it is not
squashed or stretched.
After commissioning the appliance,
ensure that the water outlet does not
leak.
90
Page 91
Technical data
Dishwasher model Standard XXL
Technical data
Height 80.5 cm (adjustable +
6.5 cm)
Height of building-in recess Min. 80.5 cm (+ 6.5
cm)
Width 59.8 cm 59.8 cm
Width of building-in recess 60 cm 60 cm
Depth 57 cm 57 cm
Weight Max. 53 kg Max. 59 kg
Voltage See data plate
Rated load See data plate
Fuse rating See data plate
Power consumption when
switched off
Power consumption when not
switched off
Test certificates awarded See data plate
Water pressure (flow rate) 50 - 1000 kPa
0.2 W 0.2 W
2.0 W 2.0 W
(0.5 - 10 bar)
84.5 cm (adjustable +
6.5 cm)
Min. 84.5 cm (+ 6.5
cm)
50 - 1000 kPa
(0.5 - 10 bar)
Hot water connection Up to max. 60 °C Up to max. 60 °C
Delivery head Max. 1 m Max. 1 m
Drainage length Max. 4 m Max. 4 m
Mains cable Approx. 1.9 m Approx. 1.9 m
Capacity 14 place settings 15 place settings
91
Page 92
Settings menu
Settings menu for changing standard settings
Opening the Settings menu
Switch the dishwasher on with the
button if it is switched off.
Use the programme selector
button to select the Further
option.
The first of the further programmes will
appear in the display.
Select the Settings option with the
arrow buttons and confirm with
OK.
The first option in the Settings menu will
appear in the display.
To learn about the display, read the
section with the same name.
Use the arrow buttons to select
the option you want to change and
confirm your selection with OK.
Sub-menu options which have already
been selected will have a tick
beside them.
To exit a sub-menu, use the
arrow buttons to select Back and
confirm with OK.
The display will revert to the menu
above.
92
Page 93
Settings menu
Language
The display can be set to appear in one
of several different languages.
You can change the language in the
display via the Language sub-menu.
Select the language you want as well
as the country, if appropriate, and
confirm with OK.
The flag after the word Language
acts as a guide if a language which
you do not understand has already
been set.
If this is the case, keep selecting the
option which has a flag after it until
you reach the Language sub-menu.
Time of day
You can select either a 24-hour or 12hour clock.
The current time of day must be set
before you can use the "FlexiTimer"
programme option.
Setting the clock format
Select the Clock format option.
Select the setting you want and
confirm with OK.
Setting the time of day
Select the Set option.
Set the hour with the arrow
buttons and confirm with OK.
Then set the minutes and confirm
with OK.
The time of day has now been saved.
93
Page 94
Settings menu
Water hardness
This appliance is fitted with a water
softener.
The dishwasher must be programmed
for the water hardness in your area.
– The dishwasher must be
programmed to the correct water
hardness for your area.
– Your local water authority will be able
to advise you of the water hardness
level in your area.
– Where the water hardness fluctuates
e.g. between 1.8 and 2.7mmol/l (1015°d - German scale), always
programme the dishwasher to the
higher value (2.7mmol/l or 15°d in
this example).
Select the water hardness level for
your area and confirm your selection
with OK.
A tick will appear beside the water
hardness which has been set.
°d mmol/l °f Display
1 0.2 2 1
2 0.4 4 2
3 0.5 5 3
4 0.7 7 4
5 0.9 9 5
6 1.1 11 6
7 1.3 13 7
8 1.4 14 8
9 1.6 16 9
10 1.8 18 10
°d mmol/l °f Display
11 2.0 20 11
12 2.2 22 12
13 2.3 23 13
14 2.5 25 14
15 2.7 27 15
16 2.9 29 16
17 3.1 31 17
18 3.2 32 18
19 3.4 34 19
20 3.6 36 20
21 3.8 38 21
22 4.0 40 22
23 4.1 41 23
24 4.3 43 24
25 4.5 45 25
26 4.7 47 26
27 4.9 49 27
28 5.0 50 28
29 5.2 52 29
30 5.4 54 30
31 5.6 56 31
32 5.8 58 32
33 5.9 59 33
34 6.1 61 34
35 6.3 63 35
36 6.5 65 36
37-45 6.6-8.0 66-80 37-45
46-60 8.2-10.7 82-107 46-60
61-70 10.9-12.5 109-125 61-70
94
Page 95
Settings menu
Rinse aid
You can adjust the rinse aid dosage for
best results.
The rinse aid dosage is set in stages
from 0 to 6.
It is set to 3 at the factory.
If the "Adjust Automatic" programme
function (depending on model) has
been activated, the amount of rinse aid
dispensed in the Automatic programme
can be higher than that set.
If spots appear on crockery and
glassware:
– Increase the rinse aid dosage.
If clouding or smearing appears on
crockery and glassware:
– Decrease the rinse aid dosage.
Select the setting you want and
confirm your choice with OK.
Consumption (EcoFeedback)
You can programme the dishwasher so
that the energy and water consumption
of the currently selected programme
appears in the display. The estimated
consumption can be displayed before
the programme starts and the actual
consumption can be displayed after the
programme has finished.
In this menu you can also call up the
total energy and water used in all
previous dishwasher programmes (see
"Caring for the environment EcoFeedback consumption indicator").
Consumption indicator
Select the Display option and confirm
with OK.
Select the setting you want and
confirm with OK.
Total consumption
Select the Total consumption option
and confirm with OK.
You can call up the values for Energy
and Water with the arrow
buttons.
You can also reset the values for the
total consumption to 0.
Select the Reset option and confirm
with OK.
Select the Yes option and confirm
with OK.
Confirm the message with OK.
The values are now reset to 0.
95
Page 96
Settings menu
EcoStart
In order to run your dishwasher in the
most economical way, you can use the
EcoStart option to take advantage of
your electricity supplier's time variable
tariffs (see "Programme options FlexiTimer with EcoStart").
With this option selected, your
dishwasher will start automatically at
your electricity supplier's cheapest tariff
times.
To use this option, you must first set up
to three electricity tariff time zones in
which the dishwasher can start. You
can allocate different priorities to these
time zones. The time with the cheapest
electricity tariff will be given Priority 1.
Contact your electricity supplier to find
out the times of the cheapest electricity
tariffs.
Once the electricity tariff times have
been set, you can use the EcoStart
option to set the latest finish time
required for each programme.
The dishwasher will then start
automatically in the cheapest electricity
tariff time and the programme will end
at the latest at the finish time set.
Setting the electricity tariff times
Before you can use the EcoStart option,
you must set at least one electricity
tariff time.
Use the arrow buttons to select
the electricity tariff time (T1-T3) you
want to set and confirm with OK.
The start of the electricity tariff time
selected will appear in the display and
the hour number block will be
highlighted.
Use the arrow buttons to set the
hours and minutes for the start time
and confirm both with OK.
The end of the electricity tariff time
selected will appear in the display and
the hours number block will be
highlighted.
Use the arrow buttons to set the
hours and minutes for the end time
and confirm both with OK.
The electricity tariff time will be saved
and its priority will appear in the display.
Use the arrow buttons to set the
priority you want and confirm with
OK.
Confirm the message with OK.
96
The electricity tariff time will be
activated.
Page 97
Settings menu
Changing the electricity tariff times
You can change the start, finish or
priority of an electricity tariff time.
Use the arrow buttons to select
the electricity tariff time (T1-T3) you
want to change and confirm with OK.
Select the setting you want to change
and confirm with OK.
Use the arrow buttons to change
the setting and confirm with OK.
Confirm the message with OK.
The change will be saved.
Deleting the electricity tariff times
You can delete the settings for an
electricity tariff time and in doing so
deactivate the EcoStart option for this
time zone.
Use the arrow buttons to select
the electricity tariff time (T1-T3) you
want to delete and confirm with OK.
For example, select Delete T1 and
confirm with OK.
For example, select Delete T1? and
confirm with OK.
The settings for the electricity tariff time
selected will be reset.
Confirm the message with OK.
The electricity tariff time has now been
deleted.
97
Page 98
Settings menu
Soak
You can use this function to loosen
dried-on food residues in the
programme selected.
Once activated, this function will be
carried out with all programmes until
you deactivate it.
If you are using powder dishwasher
detergent, add approx. 5 g to
compartment I.
Select the setting you want and
confirm with OK.
Pre-wash
You can use this function to remove
easily loosened food residues in the
programme selected.
Once activated, this function will be
carried out with all programmes until
you deactivate it.
Select the setting you want and
confirm with OK.
Brightness
There are seven different display
brightness settings.
Select the brightness you want and
confirm this with OK.
Volume
A sequence of audible tones will sound
at the end of the programme or if there
is a fault as long as the buzzer has been
activated.
Buzzer in the event of a fault
The buzzer in the event of a fault will
sound four times at intervals with a
short pause between each set of tones.
The buzzer which sounds when there
is fault cannot be deactivated.
Buzzer at the end of a programme
The buzzer at the end of a programme
will sound four times at intervals with a
short pause between each set of tones.
The volume of the buzzer which sounds
at the end of the programme can be set
to one of seven stages. If no volume is
selected, the buzzer is switched off.
Select the Buzzer tones option.
Use the arrow buttons to set the
volume required and confirm your
selection with the OK button.
Keypad tone
An audible tone sounds each time a
button is pressed.
98
The volume of the keypad tone can be
set to one of seven stages. If no volume
is selected, the keypad tone is switched
off.
Use the arrow buttons to set the
volume required and confirm your
selection with the OK button.
Page 99
Settings menu
Switching off the refill reminders
If you only ever use multi-function
combination products containing salt
and rinse aid in your dishwasher, you
can switch the refill reminders for salt
and rinse aid off if you wish. Doing so
will not affect the DetergentAgent
function (see "Programme options DetergentAgent").
Select the setting you want and
confirm with OK.
If you switch to using detergent that
does not contain salt or rinse aid, it
is important to remember to add
dishwasher salt and rinse aid and to
switch the reminders back on.
Check filters
You can adjust the interval at which the
message to remind you to check the
filters appears.
You can set an interval of between 30
and 60 programme cycles.
Automatic
You can adjust the Automatic
programme so that it will remove
stubborn soiling from an otherwise
lightly soiled load. This will increase
energy consumption.
Select the setting you want and
confirm with OK.
AutoOpen
At the end of programmes with a drying
phase the door will open automatically
a little in order to help the drying
process (see "Programme chart").
In the ECOprogramme the door will
open automatically during the drying
phase. In the
QuickPowerWashprogramme it will open
a few minutes after the programme has
finished.
This function can be deactivated if
wished.
Select the setting you want and
confirm with OK.
The "Check filters" message is set at
the factory to appear after every 50
programme cycles.
Select the interval you want and
confirm this with OK.
If you have deactivated the
automatic door opening function but
would still like to open the door at
the end of the programme, then
make sure that you open the door
fully. Otherwise steam from the
dishwasher could damage the edge
of the worktop because the fan is no
longer running.
99
Page 100
Settings menu
Optimise standby
The dishwasher is supplied with the
Optimise standby function switched on as
standard.
To save energy, the dishwasher will
switch off automatically a few minutes
after the last time a sensor has been
pressed or after the end of a
programme.
The dishwasher will not switch off in
the event of a fault.
Optimise standby can be switched off if
you prefer. If you do this, the duration
before the dishwasher switches off
increases to 6 hours. Doing this will
increase energy consumption.
Select the setting you want and
confirm with OK.
Heat exchanger
This dishwasher is equipped with a heat
exchanger (see "Programme options,
Heat exchanger).
Status
The heat exchanger function can be
switched off if you do not wish to use it.
Select the State option.
Select the setting you want and
confirm with OK.
Manual discharge
You can manually empty the heat
exchanger, e.g. for a longer period of
down time, or before moving the
appliance to a new location.
Select the Empty manually option and
confirm with OK.
The process starts straight away.
100
Loading...