Help protect our environment.......................................21
3
Page 4
IMPORTANT SAFETY INSTRUCTIONS
Correct usage
WARNING- When using your
appliance follow basic
precautions, including the
following:
Read all instructions before
installation or use to prevent
injury and appliance damage.
This appliance conforms to all
uniform safety codes and
regulations.
This appliance is intended for
~
residential use only. Only use the
appliance for its intended purpose as
described in this manual.
Other uses are not permitted and can
be dangerous.
Persons who lack physical, sensory
~
or mental abilities, or experience with
the appliance should not use it without
supervision or instruction by a
responsible person.
Read all operating and installation
instructions for appliances
installed in combination with the
plate warmer.
Keep these operating instructions
in a safe place and pass them on
to any future user.
SAVE THESE INSTRUCTIONS
Children
Close supervision is necessary
~
when any appliance is used by or near
children.
Do not let children access the
~
appliance or its controls.
Ensure that any packing material, is
~
disposed of safely and kept out of the
reach of children. Danger of
suffocation!
4
Page 5
IMPORTANT SAFETY INSTRUCTIONS
Technical safety
Before installing the appliance,
~
check for externally visible damage.
Do not operate a damaged appliance.
Be certain your appliance is
~
properly installed and grounded by a
qualified technician. To guarantee the
electrical safety of this appliance,
continuity must exist between the
appliance and an effective grounding
system. It is imperative that this basic
safety requirement be met. If there is
any doubt, have the electrical system of
the house checked by a qualified
electrician.
Before installation make sure that
~
the voltage and frequency listed on the
data plate correspond with the
household electrical supply. This data
must correspond in order to avoid risk
of damage to the appliance. If in doubt,
consult a qualified technician.
Do not use the appliance until it has
~
been properly installed into cabinetry.
Hardwiring the appliance should be
~
performed by a certified electrician in
compliance with all local and national
codes, and requirements.
Do not operate any appliance with a
~
damaged cord or plug, or if the
appliance has been damaged in any
manner. Contact Miele’s Technical
Service Department.
Defective components should be
~
replaced by Miele original spare parts
only. Only with these parts can the
manufacturer guarantee the safety of
the appliance.
Before installation or service,
~
disconnect the appliance from the
power supply by either removing the
fuse, "tripping" the circuit breaker or
unplugging the unit. Pull the plug not
the cord.
Do not use an extension cord to
~
connect this appliance to electricity.
Extension cords do not guarantee the
required safety of the appliance.
Never open the outer casing of the
~
appliance. Tampering with electrical
connections or components and
mechanical parts is dangerous and
could cause machine damage.
Installation, repair and maintenance
~
work should be performed by a Miele
authorized service technician. Work by
unqualified persons could be
dangerous and may void the warranty.
While the appliance is under
~
warranty repairs should only be
performed by an authorized service
technician. Otherwise the warranty is
void.
Do not install
~
outdoors.
5
Page 6
IMPORTANT SAFETY INSTRUCTIONS
Safety
The plate warmer interior, the top in
~
particular, gets very hot when in use
and remains hot for some time once
turned off. Use caution.
Protect your hands with oven mitts
~
or potholders when using the
appliance. Use only dry, heat resistant
potholders. Moist or damp potholders
used on hot surfaces can result in
steam burns.
Pull the drawer out all the way when
~
removing dishes to avoid touching hot
drawer parts.
Do not use the plate warmer to
~
reheat, cook or keep food and drinks
warm. The condensation from food or
drinks could lead to moisture damage
in the appliance.
Do not store anything in the warming
~
drawer. Forgotten items could melt or
catch fire when the appliance is turned
on. Flammable liquids and materials
should never be stored in, above or
under the plate warmer.
Do not use a steam cleaner to clean
~
this appliance. Steam could penetrate
electrical components and cause a
short circuit. Pressurized steam may
cause permanent damage to the
surface and to components of the
appliance.
To prevent injuries, do not use
~
accessories not recommended by
Miele.
SAVE THESE INSTRUCTIONS
AND REVIEW THEM
PERIODICALLY
Do not use the plate warmer to heat
~
the room. Due to the high temperatures
radiated, objects left near the appliance
could be damaged.
Do not replace the non-slip mat,
~
e.g. with a kitchen towel.
Do not lean, sit or overload the
~
warming drawer. This will cause
damage. The drawer can hold a
maximum of 33 lbs (15 kg).
6
Page 7
a On/Off button (lights up)
b Temperature selector
c Warming drawer
d Non-slip mat
Guide to the machine
e Indicator
f Warning sticker to indicate burn hazard
7
Page 8
Before using for the first time
Clean the appliance
Remove any protective wrapping.
^
Remove the non-slip mat and clean
^
with a solution of warm water and
liquid dish soap. Dry with a soft cloth.
Clean the plate warmer, inside and
^
out, with a damp cloth and wipe dry.
Replace the non/slip mat once it has
^
completely dried.
Heat the appliance
Heat the empty plate warmer for a
^
minimum of 2 hours. Turn the
temperature selector to "Maximum"
(see "Selecting a temperature").
Vent the room when heating the
^
drawer for the first time.
Metal components have a protective
coating which may give off a slight odor
the first time your new appliance is
heated. The smell will dissipate after a
short time and does not indicate a
faulty connection.
8
Page 9
The plate warmer is only intended for warming dishes.
Do not use the plate warmer to reheat, cook or keep food
and drinks warm. Condensation from food or drinks could
cause moisture damage to the appliance.
Use pot holders when removing dishes.
The drawer can hold a maximum of 33 lbs (15 kg).
Opening and Closing
To open and close the plate warmer gently push the center of
the drawer.
Controls
The controls include the temperature selector and the On/Off
button. They are only visible when the drawer is open.
The indicator on the front of the drawer shows if the plate
warmer is turned on or off.
Using the plate warmer
9
Page 10
Using the plate warmer
Operating
Place the dishes in the plate warmer.
^
Select a temperature.
^
Turn the appliance on (j).
^
The On/Off button will light.
Close the drawer.
^
The indicator at the front of the appliance drawer lights
^
showing that the unit is on.
Turn the appliance off (k), before removing the warmed
^
dishes.
Pull the drawer out all the way to remove the dishes.
^
Selecting a temperature
The temperature selector allows you to select a temperature
between 86° and 122°F (30° and 50°C).
Do not turn the knob counterclockwise past the 12 o’clock
position or clockwise past the 6 o’clock position. Forcing it
beyond these positions will damage the temperature
selector.
10
When the selected temperature is reached, the heating
element will turn off. It turns on again when the unit cools
below the selected temperature.
The optimum temperature to preheat cups and glassware is
about 104°F (40°C). When pre-warming cups to this
temperature, the drinks will not cool as fast and the cup itself
is still cool enough to touch.
Page 11
Warming times
Capacity
Using the plate warmer
Various factors will affect the warming times:
type and thickness of the dishes,
–
quantity,
–
how the dishes are arranged, and
–
the temperature setting.
–
As you use the plate warmer you will learn which settings suit
your needs best.
As a guideline:
It will take approx. 30 - 40 minutes to evenly warm dishes at
the maximum temperature setting of 122°F (50°C).
The quantity which can be loaded will depend on the size of
your dishes.
Example:
– 25 Cappuccino cups or
– 56 Espresso cups
Insert the cups or glassware upside down in the plate
warmer to ensure an even warming.
The maximum load is 33 lbs (15 kg).
11
Page 12
Cleaning and care
Allow the appliance to cool before
cleaning.
Do not use a steam cleaner to clean
this appliance. Pressurized steam
could penetrate electrical
components and cause a short
circuit.
Do not use commercial cleaning
agents. Only use agents
recommended for domestic use.
All surfaces of the appliance are
susceptible to scratching.
Breakages can occur on glass
surfaces.
To better maintain your appliance
avoid the following:
cleaners containing soda, ammonia,
–
thinners, or chlorides
cleaners containing descaling
–
agents,
abrasive cleaners,
–
stainless steel cleaners,
–
dishwasher soap (powder),
–
caustic (oven) cleaners,
–
scouring pads, steel wool, hard
–
brushes,
– metal scrapers
Non-slip mat
Appliance front / interior
Remove spills as soon as possible.
Otherwise the soiling may become
hard to remove.
If spills are allowed to sit for an
extended period of time or if
unsuitable cleaning agents are used
the surfaces may discolor or
change.
^
Clean the appliance with a solution of
warm water and liquid soap applied
with a soft sponge. Dry with a soft
cloth.
Glass cleaners may be used to
clean the exterior. However do not
allow them to sit or "puddle", this can
cause damage to the surface.
Remove the cleaner promptly.
12
The mat can be removed to clean the
bottom of the drawer.
^ Clean the mat by hand with warm
water and liquid dish soap.
^ Dry thoroughly. Do not return the mat
until it is completely dry.
Never clean in the washing machine
or dishwasher.
Page 13
Frequently asked questions
Repairs should only be carried out by an authorized technician in
,
accordance with local and national safety regulations. Unauthorized repairs
could cause injury or appliance damage.
The dishes are not warm enough.
Possible faultSolution
The appliance is turned off.Turn the appliance on with the On/Off
button.
The wrong temperature was selected.Check the temperature setting.
The dishes need more time to warm.Increase the timer setting.
See "Warming times".
The dishes are not warm.
Possible faultSolution
The main fuse has blown.Restore power.
The dishes are too hot.
Possible faultSolution
The temperature control is faulty.Contact Technical Service.
The On/Off button not light when turned on.
Possible faultSolution
The light for the On/Off button is faulty.Contact Technical Service.
13
Page 14
Technical Service
In the event of a fault which you cannot
easily fix yourself, please contact the
Miele Technical Service Department at
the address on the back of this booklet.
When contacting Technical Service
please quote the serial number and
model of the appliance. This
information is visible on the silver data
plate supplied with the appliance.
MieleCare
(USA only)
MieleCare, our Extended Service
Contract program; gives you the
assurance of knowing that your
appliance investment is covered by 5
years of worry free ownership.
MieleCare is the only Extended Service
Contract in the industry that guarantees
repairs by a Miele Authorized Service
Provider using genuine Miele parts.
Only genuine Miele parts installed by
factory trained professionals can
guarantee the safety, reliability and
longevity of your Miele appliance.
Please note that unless expressly
approved in writing by the Miele
Service department, Extended Service
Contracts offered by other providers for
Miele products will not be recognized
by Miele. Our goal is to prevent
unauthorized (and untrained) service
personnel from working on your Miele
products, possibly doing further
damage to them, you and/or your
home.
14
To learn more about MieleCare
Extended Service Contracts, please
contact your appliance dealer or visit
us online at:
http://miele.com/mielecare
Page 15
Installation Instructions
IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE
To prevent accidents
and appliance damage
read these instructions
before
installation or use.
Page 16
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS
Before installation make sure that
~
the voltage and frequency listed on the
data plate correspond with the
household electrical supply. This data
must correspond in order to avoid risk
of damage to the appliance. If in doubt,
consult a qualified technician.
The electrical outlet should be easily
~
accessible after installing the unit.
Be sure that after installation the
~
power cord does not come into contact
with any hot surfaces.
Only install the plate warmer in
~
combination with built-in appliances
recommended by the manufacturer.
When installed with other appliances,
the warranty is void since the
manufacturer cannot guarantee the
safe use of the plate warmer.
To install the plate warmer in
~
combination with another appliance, a
built-in shelf must exist in the cabinet to
support the weight of both appliances.
To install the combination appliance
~
please see the manual supplied with
that machine.
This appliance is not designed for
~
maritime use or for use in mobile
installations such as recreational
vehicles or aircraft. However, under
certain conditions it may be possible for
an installation in these applications.
Please contact the Miele Technical
Service Department with specific
requirements.
Note to the installer:
Please leave these instructions with the
consumer of the appliance for the local
building inspectors use.
SAVE THESE
INSTRUCTIONS
When installed in combination with
~
another appliance, the plate warmer
must always be installed beneath the
other appliance. The combination
appliance can be set without a base
directly onto the plate warmer. A shelf
between the appliances is not
necessary.
16
Page 17
Installation
Installation dimensions
Miele appliances can be installed flush or proud. Discuss your installation
requirements with your architect, designer and installer.
Combination with Coffee system
* Machine with glass front
** Machine with stainless steel front
17
Page 18
Installation
Installing the appliance
Set the plate warmer into the niche, push is all the way in.
^
Be sure that is it aligned it at a right angle.
Open the drawer and fix the appliance with the two
^
supplied screws at the side panels of the cabinet.
Install the combination appliance regarding the manual
^
supplied with that machine.
18
Page 19
Aligning the appliance front
After installing the combination appliance it may be
necessary to align the appliance front and/or even the gap
between the plate warmer and the combination machine.
Flat washers are supplied beneath the knurled nuts, which fix
the drawer to the telescopic runners.
Loosen the knurled nuts and take the drawer out.
^
Align and even the gap with the flat washers by changing
^
their position (above or below the drawer), on both sides.
Installation
19
Page 20
Electrical connection
CAUTION: Before servicing,
,
disconnect the power supply by
either removing the fuse, shutting off
the power main or manually
"tripping" the circuit breaker.
Power supply
This appliance is equipped witha5ft
(1.5 m) long power cord with a
three-prong grounding plug ready for
connection to a 120 V, 15 A, 60 Hz
power supply.
Installation work and repairs should
only be performed by a qualified
technician in accordance with all
applicable codes and standards.
Repairs and service by unqualified
persons could be dangerous.
Before connecting the appliance to
the power supply, make sure that
the voltage and frequency listed on
the data plate correspond with the
household electrical supply. This
data must correspond to prevent
machine damage. Consult an
electrician if in doubt.
When another appliance is installed
in combination with the warming
drawer to the same circuit, operating
both appliances at the same time
may cause an overload. If in doubt
consult a qualified electrician.
Further installation details are on the
wiring diagram.
20
Page 21
Help protect our environment
Disposal of packing materials
The cardboard box and packing
materials are biodegradable and
recyclable. Please recycle.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of children.
Danger of suffocation!
Disposal of an old appliance
Old appliances contain materials that
can be recycled. Please contact your
local recycling authority about the
possibility of recycling these materials.
Before discarding an old appliance
disconnect it from the electrical supply
and cut off the power cord to prevent it
from becoming a hazard.
212223
Page 22
Page 23
Page 24
Alteration rights reserved / 1609
For the most updated manual see the Miele web site.
M.-Nr. 07 342 340 / 01
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.