Midmark DM-FTC001, DM-FTC003, DM-FTC004, DM-FTC002 Installation Instructions Manual
Page 1 of 16
RECOMMENDED TOOLS
• Screwdriver, straight blade and phillips.
• Level
• Tape Measure
• 1/4" socket and ratchet
• Open end / box end wrenches
• 3/8" masonary bit
• 9/32" wood bit
• Hammer drill
RECOMMENDED FASTENERS
(Supplied)
Wood Floor
042-0209-00 Screw, Lag (3/8" x 2 1/2") Qty 4
045-0001-00 Washer, Flat (3/8") Qty 4
Concrete Floor
042-0208-00 Anchor, Wedge (3/8" x 3 1/2") Qty 4
045-0001-00 Washer, Flat (3/8") Qty 4
Brackets / Shims
050-5812-X0 Anchor, Mounting Clip Qty 4
053-1242-00 Shims Qty 4
ADDITIONAL HARDWARE
(Supplied)
040-0010-12 Mounting Screws (10-24 x 5/8") Qty 4
045-0001-08 Lockwashers, Internal (#10) Qty 4
040-0010-48 Particle Bd. Screws (#10 x 5/8") Qty 4
053-0668-00 Shelf Clips Qty 4 / shelf
TASK LIGHT CONFIGURATIONS
Task Light w/ RH Clock & LH Viewer
Task Light w/ Clock-RH Mounted
Task Light w/ Clock-LH Mounted
Task Light (Full)
Task Light w/ LH Clock & RH Viewer
Task Light w/ RH Filler Panel
Task Light w/ LH Filler Panel
DA135400i
Shown with:
Task Light, Right-hand
Clock and Left-hand
Viewer.
MODEL: DM-FTC001,
002, 003, 004
Installation
Instructions
Page 2 of 16
Electrical
Supply
120 VAC / 15 Amp / 60 Cycle
3-wire, Dedicated Circuit
Cabinet
Electrical
Terminal
Box
Outlets
Vacuum
Supply
Air
Supply
Water
Supply
Back
Finished Floor
Front
Top View of Base
Right Side Plumbin g
Rough-In Perimeter
NOTE
Midmark Casework unit must be connected to a
dedicated circuit breaker rated 15 amps, 120 VAC.
Failure to comply could result in a n ov e r load of the
electrical circuit and / or components.
All electrical and plumbing connections must be made
by a licensed electrician and plumbing contractor following applicable local, city, and national codes.
Midmark Casework unit contains 4 electrical duplex
outlets, which are rated at a combined 15 amps
.
This rating must be taken into account when plugging
device(s) into the available outlets.
Figure 1
Floor Layout
(as applicable)
A - The floor layout (Figure 1).
NOTE
A full size pre-installation Floor
Template (003-1270-00 ) and
Wall Template (003-1352-00)
are available upon request or
refer to rough-in dimensions on
next page (Figure 2 & 3).
B - Have licensed electrical and
plumbing contractors position
and install electrical outle t
receptacles and related plumbing using the pre-installation
template or layout (Figure 1).
NOTE
Assure floor is of such construction that the unit(s) will be adequately supported and
anchored.
If necessary, contact a licensed
contractor to reinforce the floor-
Page 3 of 16
Figure 3
Figure 2
DA155800i
A
B
B
C
D
E
A
Air
Water
Vacuum
F
G
H
I
42 1/2 in
(107.9 cm)
[Metal to Metal]
or
44 1/4 in
(112.4 cm)
[Panel to Panel]
21 in
(53.4 cm)
J
"A"
10 3/8"
(26.4 cm)
"F"
3"
(7.6 cm)
"B" [M to M]
3"
(7.6 cm)
"G"
15 1/2"
(39.4 cm)
"C"
1 1/8"
(2.9 cm)
"H"
2 1/2"
(6.4 cm)
"D"
6 3/16"
(15.7 cm)
"I"
12"
(30.5 cm)
"E"
7 3/8"
(18.7 cm)
"J"
6"
(15.2 cm)
"B" [P to P]
4"
(10.1 cm)
DA155900i
Air
Water
Vacuum
A
B
C
D
E
F
J
K
42 1/2 in
(107.9 cm)
[Metal to Metal]
or
44 1/4 in
(112.4 cm)
[Panel to Panel]
31.06 in
(78.9 cm)
A
G
H
I
3"
(7.6 cm)
"K"
3/4"
(1.9 cm)
"B"
9 1/2"
(24.1 cm)
"G"
11 1/8"
(28.3 cm)
"C"
3 3/4"
(9.5 cm)
"H"
11 5/8"
(29.5 cm)
"D"
3 1/4"
(8.3 cm)
"I"
26"
(30.5 cm)
"E"
8"
(20.3 cm)
"J"
4 1/8"
(10.5 cm)
"F"
12"
(30.5 cm)
4"
(10.1 cm)
"A" [M to M] "A" [P to P]
Page 4 of 16
Unpacking
NOTE
Inspect all components for shipping damage. A concealed
damage report must be f iled
with the carrier by the pers on
receiving the goods within 15
days of delivery.
A - Remove the shrink wrap, strap-
ping and cardboard filler
B - If supplied, remove the solid
panels and shelves.
C - Remove the base and midsec-
tion assembly from the skid and
place in position on floor.
D - Remove the Overhead Section
from the carton.
DA176200i
Figure 4
Solid Panel
Overhead
Page 5 of 16
Figure 5
Setting Up
NOTE
If applicable, refer to 2” Drawer
Removal on next page as removal is
different.
A- If necessary , remove the drawers by
pulling the drawer outward until it
meets resistance.
B- On both sides of drawer, pull outward
until locking slots (1) on drawer are
free of tabs (2) on drawer glides (3).
C- Lift drawer upward (4) while pulling
outward to free rear of drawer from
hooks (5) on glide.
D - On base sections that have doors,
open door and remove bottom shelf.
NOTE
When reinstalling drawers assure back
of drawer is positioned beneath hooks
(4) on glides and tabs (2) on glide snap
into locking slots (1) on drawer.
Loading...