Midmark 9A429005 User Manual

Limited WarrantyCompliance Information

General Information

FCC Compliance Statement

This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interfer­ence when the equipment is operated in a commercial
environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual,
may cause harmful interference to radio communica­tions. Operation of this equipment in a residential area
is likely to cause harmful interference in which case
the user will be required to correct the interference at
their own expense.

Any modications to this product may violate the rules

of the Federal Communications Commission and
make operation of the product unlawful.

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
recieved, including interference that may cause
undesired operation.

Declaration of Conformity

Midmark Corporation declares that

9A429001 thru 9A429005 conform to the
applicable requirements of the Radio
Equipment & Telecommunications
Equipment Directive 1999/5/EC, Annex II
Serial Number: ALL
Date: 10/13/2011
Quality Assurance Manager
Don Carr
Midmark Corporation
60 Vista Drive
P.O. Box 286
Versailles, OH 45380
U.S.A. 077-0880-00

SCOPE OF WARRANTY

Midmark Corporation (“Midmark”) warrants to the original
purchaser its new Alternate Care products and components
(except for components not warranted under “Exclusions”)
manufactured by Midmark to be free from defects in material and
workmanship under normal use and service. Midmark’s
obligation under this warranty is limited to the repair or replace­ment, at Midmark’s option, of the parts or the products the defects
of which are reported to Midmark within the applicable
warranty period and which, upon examination by Midmark, prove
to be defective.

APPLICABLE WARRANTY PERIOD

The applicable warranty period, measured from the date of
delivery to the original user, shall be one (1) year for all warranted
products and components.

EXCLUSIONS

This warranty does not cover and Midmark shall not be liable for
the following: (1) repairs and replacements because of misuse,
abuse, negligence, alteration, accident, freight damage, or
tampering; (2) products which are not installed, used, and proper­ly cleaned as required in the Midmark “Installation” and or “Instal­lation / Operation Manual” for this applicable product. (3) products
considered to be of a consumable nature; (4) accessories or
parts not manufactured by Midmark; (5) charges by anyone for
adjustments, repairs, replacement parts, installation, or other work
performed upon or in connection with such products which is not
expressly authorized in writing in advance by Midmark.

EXCLUSIVE REMEDY

Midmark’s only obligation under this warranty is the repair or
replacement of defective parts. Midmark shall not be liable for any
direct, special, indirect, incidental, exemplary, or consequential
damages or delay, including, but not limited to, damages for loss

of prots or loss of use.

NO AUTHORIZATION

No person or rm is authorized to create for Midmark any other

obligation or liability in connection with the products.

THIS WARRANTY IS MIDMARK’S ONLY WARRANTY AND
IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR
IMPLIED. MIDMARK MAKES NO IMPLIED WARRANTIES OF
ANY KIND INCLUDING ANY WARRANTIES OF MERCHANT­ABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE,
THIS WARRANTY IS LIMITED TO THE REPAIR OR
REPLACEMENT OF DEFECTIVE PARTS.

Intended Use

This product is intended to control patient positioning
while providing better patient access by eliminating the
cord from the controller(s).

Authorized CE Representative

Countries in the EEC should direct all questions, inci­dents, and complaints to Midmark’s authorized
CE Representative listed below:

Midmark Europe SAS
22, Rue de St. Denis
53500 Ernee,
FRANCE
Phone: [phone]
Fax: [phone]

Calling for Service

If service is required, contact your Midmark dealer.
To contact Midmark directly:

1-800-MIDMARK (1-800-643-6275)
Monday-Friday 8:00 am until 5:00 pm (EST)

www.midmark.com

Midmark Corporation
60 Vista Drive
Versailles, OH 45380-0286
Phone: [phone]
Fax: [phone]
www.midmark.com

User’s Guide

625 Wireless Controls

9A429

This guide outlines basic operation of the
wireless hand / foot control and the associated
base station. If service is required, contact your

authorized Midmark dealer.

Dealer (name / phone):
__________________________________
__________________________________
__________________________________
__________________________________

Date of Purchase: __________________

© Midmark Corporation 2009

003-1945-00 Rev. B

Compliance Information - continued...

IC Compliance Statement

Interference

“This device complies with Industry Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.”

“Le présent appareil est conforme aux CNR ďIndustrie Canada applicables aux
appareils radio exempts de licence. Ľexploitation est autorisée aux deux conditions
suivantes: (1) ľappareil ne doit pas produire de brouillage, et (2) ľutilisateur de
ľappareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible ďen compromettre le fonctionnement.”

Antennas

“Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry
Canada. To reduce potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not
more than that neccessary for successful communication.”

“Conformément à la réglementation ďIndustrie Canada, le présent émetteur radio peut
fonctionner avec une antenne ďun type et ďun gain maximal (ou inférieur) approuvé
pour ľémetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à ľintention des autres utilisateurs, il faut choisir le type ďantenne et son

gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas

ľintensité nécessaire à ľétablissement ďune communication satisfaisante.”

Association Procedure

The wireless controller will only function with the chair it has been “associated” with.
This prevents unwanted movement in locations with more than one chair.

Each wireless controller’s association is preset at the factory. This procedure is only
required in the event of a malfunction, if a new controller is purchased, or if you are
attempting to use the controller with a chair other than the one it was originally
associated with.

Association Procedure:

A) Disconnect power to the table for at least 3 seconds.

B*) Reconnect power, then press & hold the Stop & Home buttons
on the wireless controller, until you hear three “beeps”.

* Note: Step B must be performed within 10 seconds of Step A.

C) Check for proper operation of wireless controller.

D) If associating a hand and foot control, repeat procedure using
the other wireless controller.

Home

Stop

Home

Stop

Specifications

Range of Operation ............. 20 ft. (6 m) radius

Batteries:

Hand Control .................................AA (qty. 2)

Foot Control ..................................AA (qty. 2)

MA771100i

Troubleshooting

When any control button is pressed, that controller
sounds a single “beep”. (All functions operate)

Cause: Low battery

Solution: Replace batteries

When any control button is pressed,
nothing happens. (No “beeps”, no movement, etc.)

Cause: 1. Batteries completely dead

2. Wireless controller has lost
“association” to chair

Solution: 1. Replace batteries

2. Perform Association Procedure*

The wireless controllers will only function with the ...
chair they have been “associated” with. This prevents
unwanted movement in locations with more than one
chair.

If further service is required,

contact your authorized Midmark dealer.