Midmark 625 User Manual

FCC Compliance Statement

This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interfer­ence when the equipment is operated in a commercial
environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual,
may cause harmful interference to radio communica­tions. Operation of this equipment in a residential area
is likely to cause harmful interference in which case
the user will be required to correct the interference at
their own expense.

Any modications to this product may violate the rules

of the Federal Communications Commission and
make operation of the product unlawful.

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.

User’s Guide

625 Wireless Controls

9A429

This guide outlines basic operation of the
wireless hand / foot control and the associated
base station. If service is required, contact your
authorized Midmark dealer.

Dealer (name / phone):
__________________________________
__________________________________
__________________________________
__________________________________

Date of Purchase: __________________

Midmark Corporation
60 Vista Drive
Versailles, OH 45380-0286
Phone: [phone]
Fax: [phone]
www.midmark.com

General Information

© Midmark Corporation 2009

003-1945-00 Rev. AA2 (4/24/18)

Compliance Information

Intended Use

This product is intended to control patient positioning
while providing better patient access by eliminating the
cord from the controller(s).

Calling for Service

If service is required, contact your Midmark dealer.
To contact Midmark directly:

1-800-MIDMARK (1-800-643-6275)
Monday-Friday 8:00 am until 5:00 pm (EST)

www.midmark.com

Warranty

SCOPE OF WARRANTY Midmark Corporation (“Midmark”) warrants
to the original retail purchaser that it will, at Midmark’s option, repair or
replace components of the domestic and international medical products
manufactured by Midmark (except for components not warranted under
“Exclusions”) that are defective in material or workmanship under normal
use and service. The sole remedy under this limited warranty is the repair
or replacement, at Midmark’s option, of the applicable components. This
limited warranty shall only apply to defects that are reported to Midmark
within the applicable warranty period and which are determined to exist
upon examination by Midmark,. This warranty extends only to the original
retail purchaser of a product and is not transferable or assignable. Replace­ment components or products may be used and/or refurbished components

or products, provided they are of like quality and specications as new

components or products.

Midmark warrants to the original retail purchaser that during the appli­cable warranty period it will repair or replace software contained within the
products manufactured by Midmark (except for those not warranted under
“Exclusions”) if: (1) the media on which the software is furnished exhibits
defects in material or workmanship under normal use; or (2) the software

does not substantially conform to its published specications.

APPLICABLE WARRANTY PERIOD The applicable warranty period, mea­sured from the date of invoice to the original retail purchaser of the product
and shall be one (1) year for all warranted products and components.

OBTAINING WARRANTY SERVICE Warranty service must be obtained
through either Midmark or an authorized dealer in the Midmark product
line for which warranty service is requested. Midmark may be contacted
for warranty service inquiries or issues via email at www.midmark.com;
by phone at 1-800-MIDMARK or by mail to Midmark Corporation, 60 Vista
Drive, Versailles, Ohio 45380. It is the retail purchaser’s obligation to ar­range for delivery of a product to Midmark or one of its authorized dealers
for warranty service, which delivery shall be at retail purchaser’s expense.
It is also the retail purchaser’s obligation to comply with the warranty ser­vice instructions provided either by Midmark or its authorized dealer. The
retail purchaser must provide Midmark with completed warranty registration
information within thirty (30) days after purchase in order to obtain the

benets of this limited warranty.

EXCLUSIONS: This limited warranty does not cover and Midmark shall not
be liable for the following:
(1) Defects, damage or other conditions caused, in whole or in part, by
misuse, abuse, negligence, alteration, accident, freight damage, negligent
storage, tampering or failure to seek and obtain repair or replacement in a
timely manner;
(2) Products which are not installed, used, and properly cleaned and
maintained as required or recommended in the Midmark “Installation” and/
or “Installation/Operation Manual” for the applicable product, including the

specied structural and operational environmental conditions and electrical

requirements;
(3) Products considered to be of a consumable or sterile nature;
(4) Accessories or parts not manufactured by Midmark;
(5) Charges by anyone for adjustments, repairs, replacement parts, instal­lation or other work performed upon or in connection with such products
which are not expressly authorized in writing in advance by Midmark;
(6) Costs and expenses of routine maintenance and cleaning; and
(7) Representations and warranties made by any person or entity other
than Midmark.
(8) Matching of color, grain or texture except to commercially acceptable
standards;

(9) Changes in color caused by natural or articial light;

(10) Custom manufactured products;

(11) Alterations or modications to the product by any person or entity other

than Midmark; and

(12) Products that would otherwise by covered under this limited warranty,
but are acquired: (i) from a person or entity that is not Midmark or one of its
authorized dealers; or (ii) from a Midmark dealer that is not authorized to
sell the product at issue in the geographic territory where the purchaser is
located, or is not authorized to sell the product at issue within the medical
market.

SOFTWARE; WITH RESPECT TO SOFTWARE THAT IS A PRODUCT OR
COMPONENT THEREOF, MIDMARK DOES NOT WARRANT THAT THE
SOFTWARE: (1) IS ERROR FREE; (2) CAN BE USED WITHOUT PROB­LEMS OR INTERRUPTIONS; OR (3) IS FREE FROM VULNERABILITY
TO INTRUSION OR ATTACK BY VIRUSES OR OTHER METHODS.

EXCLUSIVE REMEDY; CONSEQUENTIAL DAMAGES DISCLAIMER
MIDMARK’S ONLY OBLIGATION UNDER THIS LIMITED WARRANTY IS
THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS. MIDMARK
SHALL NOT BE LIABLE FOR AND HEREBY DISCLAIMS ANY DIRECT,
SPECIAL, INDIRECT, INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL
DAMAGES OR DELAYS, INCLUDING, BUT NOT LIMITED TO, DAMAGES
FOR LOSS OF PROFITS OR INCOME, LOSS OF USE, LOSS OF DATA,
DOWNTIME, COVER AND EMPLOYEE OR INDEPENDENT CONTRAC­TOR WAGES, PAYMENTS AND BENEFITS. THIS DISCLAIMER SHALL
SURVIVE ANY FAILURE OR ASSERTED FAILURE OF THE ESSEN­TIAL PURPOSE OF THIS LIMITED WARRANTY OR ITS REMEDIES
SPECIFIED HEREIN. WARRANTY DISCLAIMER THIS WARRANTY IS
MIDMARK’S ONLY WARRANTY AND IS IN LIEU OF ALL OTHER WAR­RANTIES, EXPRESS OR IMPLIED. MIDMARK MAKES NO IMPLIED

WARRANTIES OF ANY KIND INCLUDING ANY IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF
DEFECTIVE PARTS.

STATUTE OF LIMITATIONS No action may be brought against Midmark for
breach of this limited warranty, an implied warranty, if any, or for any other
claim arising out of or relating to the products, more than ninety (90) days
following expiration of the limited warranty period.

NO AUTHORIZATION No person or rm is authorized to create or approve

for Midmark any other obligation or liability in connection with the products.

Style D

Specifications

Range of Operation ............. 20 ft. (6 m) radius

Batteries:

Hand Control .................................AA (qty. 2)

Foot Control ..................................AA (qty. 2)

Troubleshooting

When any control button is pressed, that controller
sounds a single “beep”. (All functions operate)

Cause: Low battery

Solution: Replace batteries

When any control button is pressed,
nothing happens. (No “beeps”, no movement, etc.)

Cause: 1. Batteries completely dead

2. Wireless controller has lost
“association” to chair

Solution: 1. Replace batteries

2. Perform Association Procedure*

The wireless controllers will only function with the
chair they have been “associated” with. This prevents
unwanted movement in locations with more than one
chair.

If further service is required,

contact your authorized Midmark dealer.

Association Procedure

The wireless controller will only function with the chair it has been “associated” with.
This prevents unwanted movement in locations with more than one chair.

Each wireless controller’s association is preset at the factory. This procedure is only
required in the event of a malfunction, if a new controller is purchased, or if you are
attempting to use the controller with a chair other than the one it was originally
associated with.

Association Procedure:

A) Disconnect power to the table for at least 3 seconds.

B*) Reconnect power, wait for the power up beep sequence from
the table, then press & hold the Stop & Home buttons on the
wireless controller until you hear three “beeps”.

* Note: Step B must be performed within 10 seconds of the power up beep
sequence from the table.

C) Check for proper operation of wireless controller.

D) If associating a hand and foot control, repeat procedure using
the other wireless controller.

Stop

Home

MA771100i

Home

Compliance Information - continued...

IC Compliance Statement

Interference

“This device complies with Industry Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.”

“Le présent appareil est conforme aux CNR ďIndustrie Canada applicables aux
appareils radio exempts de licence. Ľexploitation est autorisée aux deux conditions
suivantes: (1) ľappareil ne doit pas produire de brouillage, et (2) ľutilisateur de
ľappareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible ďen compromettre le fonctionnement.”

Antennas

“Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry
Canada. To reduce potential radio interference to other users, the antenna type and its
gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not
more than that necessary for successful communication.”

“Conformément à la réglementation ďIndustrie Canada, le présent émetteur radio peut
fonctionner avec une antenne ďun type et ďun gain maximal (ou inférieur) approuvé
pour ľémetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à ľintention des autres utilisateurs, il faut choisir le type ďantenne et son

gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas

ľintensité nécessaire à ľétablissement ďune communication satisfaisante.”

Stop