Page 1
PRODUCTS USERMANUAL
WIFI+BT Module
Midea_IOT10M_P1
IEEE 802.11a/b/g/n
Model Number: Midea_IOT10M_P1
Product Description
1T/1R
The Midea_IOT10M_P1 is a high-gain and low power consumption wifi module . It fully complies
with IEEE 802.11a/b/g/n feature rich wireless connectivity at high standards,delivers
reliable,cost-effective,throughput from an extended distance.When
5V, UART and GND were connected,This module is working. The Bluetooth part supports latest 4.2LE
operation.
Product Specification
Product Features
◆ Complies with IEEE 802.11g;
802.11b; 802.11n ; 802.11a ;standard
for 2.4GHz and 5GHz Wireless LAN.
◆ONE Transmit and ONE Receive
path(1T1R)
◆Supports Ad-Hoc/Infrastructure modes
◆ Works with all existing network
frastructure.
◆Capable of up to 128-Bit WEP
Encryption.
◆Freedom to roam while staying
connected.
◆ UP to 150Mbps High-Speed Transfer
Rate in 802.11N mode of operation.
◆ Operating Systems：Linux
◆ Low power consumption.
◆Complies with UART base specification
revision 1.1 for WLAN
◆ Easy to install and configure.
◆Bluetooth v4.2 Low Energy(LE);
Model
Product Name
Standard 802.11a/b/g/n
Interface WiFi：UART BT：UART
Data Transfer Rate 1,2,5.5,6,11,12,18,22,24,30,36,48,54,60,9
Modulation Method QPSK,BPSK ,CCK(802.11b)
Frequency Band 2.4GHz: CH 1~CH11 for FCC
Transmit Power < 20dBm
Operation Mode Ad hoc, Infrastructure
Operation Range Up to 150 meters in open space
OS Support Linux
Security WEP, TKIP, AES, WPA, WPA2
Operating Voltage 5V±10%
Operating Temperature -30 ~ 85°C ambient temperature
Storage Temperature -40 ~ 125°C ambient temperature
Humidity 5 to 95 % maximum (non-condensing)
Midea_IOT10M_P1
WIFI+BT Module
0 and maximum of 150Mbps
QPSK,BPSK,16QAM ,64QAM with OFDM
(802.11g)
BPSK,QPSK,16QAM ,64QAM with OFDM
(802.11n)
QPSK,BPSK,16QAM ,64QAM with OFDM
(802.11a)
GFSK(BT)
5GHz: 5150~5250MHz, 5725~5850MHz
PAGE 1 OF 4
Version 1.0
Page 2
PRODUCTS USERMANUAL
Midea_IOT10M_P1
Pin Definitions
Pin Name Functional Description
GND GND
TX UART-TX,receive end in UART
download
RX UART-RX,transmit end in UART
download,floating or pull up
5V 5V power supply
NOTICE:
◆please keep this product and accessories attached to the places which children can't touch;
◆do not splash water or other liquid onto this product, otherwise it may cause damage;
◆do not put this product near the heat source or direct sunlight, otherwise it may cause
deformation
◆or malfunction;
◆please keep this product away from flammable or naked flame;
◆please do not repair this product by yourself. Only qualified personnel can be repaired.
◆5G WIFI 5150-5250MHz shall be indoor use only.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
PAGE 2 OF 4
Version 1.0
Page 3
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-Consult the dealer or an experienced radio/TV technician for help.
PRODUCTS USERMANUAL
Midea_IOT10M_P1
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Please notice that if the FCC identification number is not visible when the module is installed
inside another device, then the outside of the device into which the module is installed must
also display a label referring to the enclosed module. This exterior label can use wording such
as the following: “Contains FCC ID: VG8IOT10MP1” any similar wording that expresses the same
meaning may be used.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitterandmustbeinstalledtoprovideaseparationdistanceofatleast20cmfromallpersons.
The module is limited to OEM installation ONLY.
The OEM integrator is responsible for ensuring that the end-user has no manual instruction to
remove or install module.
The module is limited to installation in mobile application.
A separate approval is required for all other operating configurations, including portable
configurations with respect to Part 2.1093 and difference antenna configurations.
There is requirement that the grantee provide guidance to the host manufacturer for compliance
with Part 15B requirements.
The module complies with FCC Part 15.247 / Part 15.407 and apply for Single module approval.
Trace antenna designs: Not applicable.
Antennas:
2.4G 5G
PCB antenna & 3 dBi PCB antenna & 3 dBi
The antenna is permanently attached, can’t be replaced.
PAGE 3 OF 4
Version 1.0
Page 4
PRODUCTS USERMANUAL
Midea_IOT10M_P1
Canada Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the
following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d’en compromettre le fonctionnement.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter
andmustbeinstalledtoprovideaseparationdistanceofatleast20cmfromallpersons.
matériel est conforme aux limites d'exposition aux
Ce
ne doit pas être
adapté à une distance minimale de 20cm entre le radiateur
situées ou opérant conjointement avec toute autre antenne ou l'émetteur.
rayonnements rf énoncées dans un autre environnement.cet émetteur
Ce matériel devrait être installé et
et votre corps.
Please notice that if the ISED certification number is not visible when the module is installed
inside another device, then the outside of the device into which the module is installed must
also display a label referring to the enclosed module. This exterior label can use wording such
as the following: “Contains IC: 21015-IOT10MP1” any similar wording that expresses the same
meaning may be used.
l'appareil hôte doit porter une étiquette donnant le numéro de certification du module
d'Industrie Canada, précédé des mots « Contient un module d'émission »,du mot « IC:12290A-WCT5L
» ou d'une formulation similaire exprimant le même sens, comme suit
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential
for harmful interference to co-channel mobile satellite systems.
Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une
utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes
de satellites mobiles utilisant les mêmes canaux.
PAGE 4 OF 4
Version 1.0
Loading...