Midea KJR-12B/DP-F-2, KJR-12B/DT-F-1, KJR-12B/DT-F-2, YORK-KJR-12B/DP-E-2, YORK-KJR-12B/DT-E-2 Owner's Manual

...

Download

Page 1

WIRED REMOTE CONTROLLER

Owner’s Manual

MODEL: KJR-12B/DP(T)-F-1

KJR-12B/DP(T)-E-1A KJR-12B/DP(T)-E-2 RCW8(P/N:7ACEL1706) YORK-KJR-12B/DP(T)-E-2 WP-KJR-12B/DP(T)-E-2

IMPORTANT NOTE: Read this manual carefully before

installing or operating your wired remote controller. Make sure to save this manual for future reference.

Page 2

Page 3

1. Remote Control Buttons ......................................... 01

2. LCD Screen ............................................................ 04

3. Basic Functions ....................................................... 05

4. Troubleshoot your remote control ............................15

Table of Contents

Page 4

Remote Control Buttons

M O DE B UTTO N

TIMER ON B UTTON

FOLLOW M E BUTTON

TIMER OF F BUTTO N

AUX IL I A RY ELEC T R I C AL H EAT E R

R E S ET BUTTO N

O N /OFF B UTTO N

A DJU ST BUTTON

SWIN G BUTTO N

ECONOMY BUTTON

FAN SPEED BUTTON

L OCK BUTTO N

TIMER

OFF

AUXIL

HEATER

MODE

RESET

LOCK

FANSPEED

ECO

SWING

TEMP

• Used to select the operating mode

• For cooling-only units, there is no

HEAT function.

• Used to automatically

turn on the air conditioner at a specif ied time.

• Used to automatically

turn off the air conditioner at a specif ied time.

• Allows the remote

control to act as a remote thermostat and relay temperature information from its current location.

• The Auxiliary Electric Heater

warms up the unit in cold climates.

• If pressed during HEAT mode,

the electric heater function becomes ineffective.

• Used to restore the system

to its default settings.

• Used to start/stop the air conditioner.

• The UP (

▲ )

and DOWN (▼

)

buttons are used to adjust the temperature.

• Press these two buttons

at the same time to switch between Celsius and Fahrenheit (some models)

• The SWING button starts

and stops the louver movement and sets the desired airflow direction.

• Used to activate/deactivate ECONOMY Mode, in

which the unit maintains a comfortable temperature during sleeping hours.

• Used to select the

fan speed.

• Used to lock/unlock

the current setting.

Low Med .

High

AUTO

COOL DRY HEAT FAN

→→→

→

Fig. 1

Page 5

M O DE B UTTO N

TIMER ON B UTTON

I-FEEL BUTTON

TIMER OF F BUTTO N

HEATER BUTTON

R E S ET BUTTO N

O N /OFF B UTTO N

A DJU ST BUTTON

SWIN G BUTTO N

SLEEP BUTTON

FAN SPEED BUTTON

L OCK BUTTO N

TIMER

OFF

I-FEEL

HEATER

MODE

RESET

LOCK

FANSPEED

SLEEP

SWING

TEMP

• Used to select the operating mode

• For cooling-only units, there is no

HEAT function.

• Used to automatically

turn on the air conditioner at a specif ied time.

• Used to automatically

turn off the air conditioner at a specif ied time.

• Allows the remote

control to act as a remote thermostat and relay temperature information from its current location.

• The Heater warms up the unit in cold climates.

• If pressed during HEAT mode,

the electric heater function becomes ineffective.

• Used to restore the system

to its default settings.

• Used to start/stop the air conditioner.

• The UP (

▲ )

and DOWN (▼

)

buttons are used to adjust the temperature.

• The SWING button starts

and stops the louver movement and sets the desired airflow direction.

• Used to activate/deactivate SLEEP Mode, in

which the unit maintains a comfortable temperature during sleeping hours.

• Used to select the

fan speed.

• Used to lock/unlock

the current setting.

Low Med .

High

AUTO

COOL DRY HEAT FAN

→→→

→

Fig. 2

Page 6

WARNING

•

DO NOT

remove the cover or touch the interior parts of the remote control.

•

DO NOT use sharp or pointed objects to press the

remote control buttons.

Page 7

LCD Screen

1 121 12

Operation mode

Displays the selected operating mode

Follow me

Displayed when the FOLLOW ME feature is activated

ON/OFF

Displayed when the air conditioner is on

Timer

The “ON” sign lights up when the TIMER ON function is activated

The “OFF” sign lights up when the TIMER OFF function is activated

Temperature display

Displays the current set temperature

Lock

Displayed when the LOCK mode is on

Fan speed

Displays the selected fan speed

Fig. 3

Page 8

Basic Functions

The following are instructions for using your air conditioner’s basic functions.

AUTO Function

In AUTO mode, the unit will automatically select the COOL,

HEAT, FAN or DRY function based on the set temperature. 1

Press the MODE button, select AUTO.

2 Set your desired temperature using the UP ( ) and DOWN

( ) buttons.

Press the ON/OFF button to start the unit.

NOTE: In AUTO mode, the fan speed is automatically set

on AUTO mode and cannot be changed.ECONOMY Mode can also be activated.

TIMER

OFF

AUXIL

HEATER

MODE

RESET

LOCK

FANSPEED

ECO

SWING

TEMP

Fig. 4

Page 9

COOL/HEAT/FAN Function

1 Press the MODE button to select COOL, HEAT or FAN. 2 Set your desired temperature using the UP ( ) and DOWN

( ) buttons.

3 Press the FAN SPEED button to select the fan speed.

4 Press the ON/OFF button to start the unit.

NOTE: In FAN mode, the temperature cannot be changed.

TIMER

OFF

AUXIL

HEATER

MODE

RESET

LOCK

FANSPEED

ECO

SWING

TEMP

Fig. 5

Page 10

DRY Function

1Press the MODE button, select DRY. 2Set your desired temperature using the UP ( ) and DOWN

( ) buttons.

3Press the ON/OFF button to start the unit.

NOTE: In DRY mode, the ECONOMY and FAN SPEED buttons cannot be used.

TIMER

OFF

AUXIL

HEATER

MODE

RESET

LOCK

FANSPEED

ECO

SWING

TEMP

Fig. 6

Page 11

FOLLOW ME Function The FOLLOW ME function enables the remote control to

measure the temperature at its current location. When using AUTO, COOL, or HEAT functions, measuring ambient temperature from the remote control (instead of from the indoor unit itself) will enable the air conditioner to make sure that the temperature around you is optimized for your comfort.

Press FOLLOW ME button to activate function. The

remote control will send temperature signal to the indoor unit every three minutes.

2 Press FOLLOW ME button again to turn off this function.

NOTE: The swing function can only be used in SWING mode.

Follow Me Button

TIMER

OFF

AUXIL

HEATER

MODE

RESET

LOCK

FANSPEED

ECO

SWING

TEMP

Fig. 7

Page 12

Setting Air Flow Direction

1 Press the SWING button to activate the swing function.

Press this button again to set the louver in the position you want.

2 Press and hold the SWING button for three seconds to

make the louver move continuously.

NOTE: The swing function can only be used in SWING

mode. The swing range of the louvers is 30°.

Swing Button

TIMER

OFF

AUXIL

HEATER

MODE

RESET

LOCK

FAN SPEED

ECO

SWING

TEMP

Fig. 8

Page 13

TIMER Function Your air conditioning unit has two timer-related functions:

• TIMER ON – sets the amount of time after which the

unit will automatically turn on. (Delayed on)

• TIMER OFF – sets the amount of time after which the

unit will automatically turn on. (Delayed off)

1. TIMER ON Function The TIMER ON function allows you to set a period of time

after which the unit will automatically turn on, such as when you come home from work.

a Press TIMER ON button. By default, the last time period

that you set and an “H” (indicating hours) will appear on the display.

NOTE This number indicates the amount of time after

the current time that you want the unit to turn on. For example, if you set TIMER ON for 2 hours, “2.0 H” will appear on the screen,and the unit will turn on after 2 hours.

b Press TIMER ON button repeatedly to set the time you

want the unit to turn on.

c Wait 3 seconds, then the TIMER ON function will be

activated. The digital display on your remote control will then return to the temperature display.

Page 14

Example: Setting unit to turn on after 2.5 hours

3 sec

TIMER

2. TIMER OFF Function The TIMER OFF function allows you to set a period of time after which the unit will automatically turn off, such as when you wake up.

Example: Setting unit to turn on after 5 hours

NOTE: When setting the TIMER ON or TIMER OFF functions, up to 10 hours, the time will increase in 30 minute increments with each press. After 10 hours and up to 24, it will increase in 1 hour increments. The timer will revert to zero after 24 hours. You can turn off either function by setting its timer to “0.0 H.”

sec

x10

TIMER

OFF

TIMER

OFF

Fig. 9

Fig. 10

Page 15

Setting both TIMER ON and TIMER OFF at the same time (Combined Timer Function)

Keep in mind that the time periods you set for both functions refer to hours after the current time. For example, say that the current time is 1:00 PM, and you want the unit to turn on automatically at 7:00 PM. You want it to operate for 2 hours, then automatically turn off at 9:00 PM.

Do the following:

Press TIMER ON button. The last TIMER ON setting will

appear.

2. Press TIMER ON button repeatedly until “6.0 H” is displayed on remote control. (6 hours after 1:00 PM, which is 7:00 PM.)

3. Wait 3 seconds, and the TIMER ON function will be activated.

Then press TIMER OFF button. The last TIMER OFF

setting will appear.

5. Press TIMER OFF button repeatedly until “8.0 H” is displayed on remote control. (8 hours after 1:00 PM, which is 9:00 PM.)

Wait 3 seconds, and the TIMER OFF function will be activated.

Page 16

x12

3 sec

1 2 3 4

TIMER

Fig. 11

x16

3 sec

4 5 6

TIMER

OFF

TIMER

OFF

Page 17

The unit will now turn on after 6 hours (7:00 PM) and turn off again after 8 hours (9:00 PM). (See Fig. 11)

Fig. 12

Current time 1PM

2PM 3PM

4PM 5PM

6PM 7PM 8PM 9PM

Timer starts

Unit turns

OFF

6 hours later

8 hours later

Timer is set to turn ON 6 hours from current time

Timer is set to turn OFF 8 hours from current time

Your remote display

Page 18

Troubleshoot Your Remote Control

Symptoms Possible Causes Solution

The fan speed cannot be changed.

Check whether AUTO mode is selected.

In AUTO mode, the fan speed is

set automatically and cannot be changed.

Check whether DRY mode is selected.

In DRY mode, the FAN SPEED button is ineffective. The fan speed can only be changed in COOL, FAN and HEAT mode.

The temperature display is off

Check whether FAN mode is selected.

In FAN mode, the temperature cannot be adjusted.

The TIMER OFF disappears after a period of time

If the TIMER OFF function was activated, the operation may have ﬁnished.

The air conditioner will automatically stop at the set time and the indicator light will turn off.

The TIMER ON indicator disappears after a period of time

If the TIMER ON function was activated,the operation may have ﬁnished.

The air conditioner will automatically start at the set time and the indicator light will turn off.

There is no sound when the ON/OFF button is pressed.

Check whether the signal transmitter of the remote control is properly directed towards the infrared signal receiver of the indoor unit.

Point the remote control directly at the receiver

and press the

ON/OFF

button twice.

Page 19

16117100000240

QSXU-008AEN

The design and specifications are subject to change without prior notice for product improvement.Consult with the sales agency or manufacturer for details.

20161102