- 1 -
Media Series Single-Door
Single-Temperature Electric Control
Beverage Cooler
User Manual
Model: WF130
- 2 -
Content
Important Safety Instructions…………………………………………….3
Hint for Castoff Disposal…………………………………………………..4
Hints on Safety & Warning………………………………………………..5
Before Using Your Beverage Cooler…………………………………….7
Installation of Your Beverage Cooler…………………………………….7
Placement of Beverage Cooler …………………………………………..8
Connect Beverage Cooler with Power Source…………………………9
Know About Beverage Cooler……………………………………………10
Level the Beverage Cooler………………………………………………..10
Turn on the Beverage cooler and set up temperature………………11
Hints for Operation………………………………………………………..12
Placement of Beverage Bottle…………………………………………..12
Effective Cubage…………………………………………………………...12
Use Temperature Area in Chilling Cabinet……………………………12
Practical Skills for Storage of Beverage……………………………….13
Power-off & Stop Using of Beverage Cooler………………………….13
Cleaning Beverage Cooler ………………………………………………14
Energy Saving………………………………………………………………14
Operation Noise……………………………………………………………15
Troubleshooting By Yourself………………………………………...15
- 3 -
Important Safet y Instructions
WARNING
To reduce the risk of fire, electrical shock, or injury when using your
Wine/Beverage Cooler, follow these basic precautions:
This appliance is intended to be used in household and similar applications such as
– staff kitchen areas in shops, offices and other w orking env ir onme nts;
– farm houses and by clients in hotels, motels and other residential type environments;
– bed and breakfast type environments;
– catering and similar non-retail applications.
This appliance is no t i nt en ded for u se by p erso ns ( in cl udin g c hildren) with reduced p hy si cal, se nsory or mental capabil itie s ,
or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
WARNING: Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.
– WARNING: Do not use mechanical devices or other means to accelerate the defrosting process, other than those
recommended by the manufacturer.
– WARNING: Do not damage the refrigerant circuit.
– WARNING: Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of
the type recommended by the manufacturer.
Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
Children should be supervised to ensure that they do not play with the appliance.
Never clean Wine/Beverage Cooler parts with flammable fluids. The fumes can create a fire hazard or explosion.
Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this or any other appliance. The
fumes can create a fire hazard or explosion.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
WARNING
--- Do not damage the refrigerant circuit.
--- Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
--- Use two or more people to move refrigerator.
--- The appliance is not intended for use by young children or infirm persons without supervision.
--- Young children should be supervised to ensure that they do not play with the appliance
--- If the supply cord or other components damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
CAUTION: Do not use extension cord.
DANGER:
Risk of child entrapment. Before you throw away your old refrigerator or freezer:
Take off the door
Leave the shelves in place so that children may not easily climb inside.
-Save these instructions-
- 4 -
Hint for Castoff Disposal
Disposal of Waste Package
The package is used to protect the Beverage Cooler during the transportation.
All the materials are harmless to environment and reusable.
To know the current channel for disposal of castoff, please consult your
professional dealers or the local administrative authority.
Warning
For the discarded Beverage Cooler:
1. Please pull out the plug of power source.
2. Please sever the electric cord and take it off with power plug.
The Beverage Cooler contains cooling agent and the insulation layer contains
gas. The cooling agent and the insulated gas must be disposed by
professional personnel. Please do not damage the loop pipeline of the cooling
agent before it’s disposed by professional personnel.
3. Risk of child entrapment.
Child entrapment and suffocation are not problems of the past. Junked or
abandoned appliances are still dangerous even if they will “just sit in the
garage a few days”.
4. Before you throw away your old Beverage Cooler: take off the doors.
Leave the shelves in place so that children may not easily climb inside.
- 5 -
Hints on Safety & Warning
Before Operation of Beverage Cooler
Please read the User Manual carefully!
It contains some important information on placement, use and maintenance of
Beverage Cooler.
Please keep all the data for future us e or t he next us er o f the Bev er age Cool er.
Technical Safety
The Beverage Cooler contains a little cooling agent, which is harmless to
the environment. Please pay attention not to damage the loop pipeline of
the cooling agent in the transportation or installation process. The ejected
cooling agent may cause injury to eyes or may ignite by itself.
When It’s Damaged
The flame or fire source should be kept away from the Beverage Cooler.
Please ventilate the room thoroughly for several minutes.
Pull out the power plug.
Inform after-sales service personnel.
The more cooling agent the Beverage Cooler has, the bigger the space to
place the Beverage Cooler should be. For every 8g cooling agent, there must
be at least 1m³ of space in the room. The quantity of Beverage Cooler is
marked on the nameplate of the back-plate of the Beverage Cooler.
The replacement of power cord and other repair activities can only be
carried out by the after-sales service personnel specified by the
manufacturers. Improper installation or repair may cause big dangers to
users.
During Use
Do not use electric appliance (such as: heater, electric ice maker, etc.)
within the inside of the Beverage Cooler.
Danger of Explosion!
Do not use steam type cleaning equipment to clean the Beverage Cooler
- 6 -
or defrost! Steam may enter the electric elements and cause short circuit.
Danger of Electric Shock!
Don’t remove frost or ice layers with sharp or keen-edg ed obj ect.
Otherwise, the cooling ag ent pipel i ne may be dam ag ed. The ej ec te d
cooling agent may cause injury to eyes.
Do not store produc ts that c ont ains c ombus ti bl e gas ( such as: spray bottle)
or explosive materials in the Beverage Cooler.
Danger of Explosion!
Do not use the base or the door of the Beverage Cooler as footplate or
support.
When you defrost or clean the Beverage Cooler, please pull out the power
plug or disconnect th e pr otecti ve eq uipm ent. When y ou pull out pow er plug ,
please hold the plug rather than pull the power cord.
The wines with high alcohol content must be sealed and stored vertically.
Avoid contamination of grease to the plastic components and the door
sealing components of the Beverage Cooler, or the plastic components
and the door seali ng components of th e B everage Cooler will appear small
holes.
Do not envelop or close the ventilation or exhaust holes.
Never clean Beverage Cooler parts with flammable fluids. The fumes can
create a fire hazard or explos ion.
Do not use extension cords.
Children
Do not give the package or other components to children for play. The
folded paperboard and the plastic film may cause danger of suffocation!
The Beverage Cooler is not toy of children!
Never allow children to operate, play with, or crawl inside the Beverage
Cooler.
- 7 -
The appliance is not intended for use by young children or infirm persons
without supervision; young children should be supervised to ensure that
they do not play with the appliance
Before Using Your Beverage Cooler
Remove the exterior and interior packing.
Check to be sure you have all of the following parts:
5 Shelves 1 Bottle/Can Basket 3 Glass S helves 1 Instruction Manual
Before connecting the Beverage Cooler to the power source, let it stand
upright for approximately 2 hours. This will reduce the possibility of a
malfunction in the cooling system from handling during transportation.
Clean the interior surface with lukewarm water using a soft cloth.
Installation of Your Bever a ge Cooler
This appliance is designed to be free standing only, and should not be
recessed or built-in (fully recessed).
Place your Beverag e C ool er on a floor that is str ong enough to support it when
it is fully loaded. To level y our Bev erage Cool er, adjust the adjus tabl e leg at the
bottom of the unit.
Allow 5 inches of space between the back and sides of the unit, which allows
the proper air circulation to cool the compressor.
Locate the Beverage Cooler away from direct sunlight and sources of heat
(stove, heater, radiator, etc.). Direct sunlight may affect the acrylic coating and
heat sources may increase electrical consumption. Extreme cold ambient
temperatures may also cause the unit not to perform properly.
Avoid locating the unit in moist areas.
Plug the Beverage Cooler into an exclusive, properly installed-grounded wall
outlet. Do not under any circumstances cut or remove the third (ground) prong
from the power cord. Any questions concerning power and/or grounding
- 8 -
should be directed toward a certified electrician or an authorized Avanti
Products service center.
After plugging the appliance into a wall outlet, allow the unit to cool down for
2-3 hours before placing items in the compartment.
Placement of Beverage Cooler
The Beverage Cooler should be placed in dry and ventilated room. The
location of the Beverage Cooler should not be irradiated by direct sunshine.
The Beverage Cooler should be far away from heating sources, such as:
cooking stove or heatin g radi ator. If the B everag e Cooler has to be placed n ear
heating source, please adopt proper heating insulation board for insulation or
keep the Beverage Cooler at least the following minimum distances away from
the heating sources:
For electric stove: 3 ㎝.
For oil or coal stove: 30 ㎝.
To ensure proper ventilation for your Beverage Cooler, allow for 40mm
space on each side between walls, 40mm space between back of your
Beverage Cooler and the wall, and 40mm space between counter top and the
roof or ceiling.
Notice
If the room temperature is lower than +16°C, the Beverage Cooler may not be
able to work normally, because if the room temperature is too low, the
temperature sensitive goods might be damaged.
If the room temperature and humidity is too high, the glass door of the
Beverage Cooler may have congealed dew.
- 9 -
Connect Beverage Cooler with Power Source
Connect Beverage Cooler with Power Source
After placing the Beverage Cooler, please wait for at least half an hour before
the Beverage Cooler can be operated. This is because the engine oil in the
compressor may flow into the cooling system during the transportation
process.
Before the first running, please clean the inside chambers of the Beverage
Cooler (Please see the section on cleaning).
The power socket sho ul d be i n s uc h as pl ace, where is reachabl e conveniently.
Please use a socket that’s installed according to the requirements. The
Beverage Cooler should be connected with 220-240V/50Hz AC power.
Warning!
In any case, please do not connect the Beverage Cooler to the electronic
energy saving power plug or the converter (such as: solar energy equipment,
ship’s electric grid) that convert DC into 220-240V AC.
Warning
Improper use of the grounded plug can result in the risk of electrical shock. If the supply cord is
damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
- 10 -
Know About Beverage Cooler
Level the Beverage Cooler
Place the Beverage Cooler on the planned location and level it.
The front screw leg is adjustable.
1
- 11 -
Turn on the Beverage Cooler and set up te m per a t ure
The screen is shown as the following picture:
+: Press this button once and the temperature increase 1°C.
-: Press this button once and the temperature decrease 1°C.
: Temperature display .
LIGHT: Lighting button for LED lamp; it controls the on/off of lamp.
POWER: On/off button used to turn on/off all load.
Press LIGHT and POWER together for 2 seconds and you can convert
between fahrenheit temperature and Celsius temperature.
Notice!
The temperature range is 1~10°C OR 4-10°C ,The default temperature of
beverage Cooler is 5°C, and the temperature after power failure will be the
temperature set before the power failure.
To elongate the service life of compressor, please wait for at least 5
minutes before the beverage Cooler is restarted after power failure.
Failure display
If there is failure on the sensor, the screen may display failure code, such
as: E and F. When the screen dis plays the abov e-mentioned er rors, please
do not disassemble it for check by yourself. You should contact local
after-sales service personnel for repair.
If the temperature in the cooler is too low, it will display “L”.
When the temperature in the cooler is too high, the screen will display “H”
and will flash; under this state, the buzzer will buzz once every one second
until 30 seconds; one minute later, the buzzer will continue to give alarm in the
next 30 seconds; after the alarm is given for three times, it will not give alarm
any more. You can press any key to cancel sound alarm.
When you put a lot of Beverage together in the cooler, the temperature in
- 12 -
the cooler may rise temporarily.
Hints for Operation
In the operation of compressor, the back wall of the chilling chamber will form
water ball or frost because this is determined by the functions of Beverage
Cooler. You do not need to defrost or wipe off water drops because the back
wall is able to defrost automatically. The defrosted water will be collected to
discharge channel and the water will flow to the water receiver above the
compressor and will be vaporized there.
When there is too much frost at the back of inner side of cabinet, pls turn off
the power until the defrosting is finished.
Placement of Beverage Bottle
When you place the beverage bottles, please note:
The number of bottles that can be put on the bottle racks is recorded on
To maintain the perfect air ventilation in the Beverage Cooler, the bottle
should not touch the back wall of the chilling chamber.
The number of cans might be different for different cans with different
shapes and sizes.
Because some space is occupied by the compressor, the lower part of the
Beverage Cooler is comparatively low and it can be used to place
beverage tins or the short beverage bottles.
Effective Cubage
Please see the model nameplate on the Beverage Cooler for the description
on effective cubage.
Use Temperature Area in Chil ling Cabinet
Due to the air circulation in the Beverage Cooler, some areas with different
temperatures are generated:
The upper area has the highest temper a tur e
The lower area has the lowest temperature
We recommend pour beverage into glass at the temperature lower than the
- 13 -
drinking temperature because the temperature of beverage will increase
quickly when it’s poured into glass.
Practical Skills for Storage of beverage
The bottled beverage should not be stored in the chilling chamber in a
whole case or box before the whole case or box has been opened.
When old bottles are placed in the Beverage Cooler, please make sure
that the bottle cork can always be wetted. Do not leave space between the
beverage and the bottle cork.
The open type bottle rack is especi al l y s ui tab l e because it will not se par ate
air circulation, so the atmosphere moisture on the bottle can be quickly
dried by air ventilation.
Please make sure that the temperature of the beverage is always lower
than the ideal drinking temperature because when you drink the beverage
into glass, the temperature of the beverage will increase 1 - 2°C
immediately!
Drinking Temperature
Power-off & Stop Using of Beverage Cooler
Turn off Beverage Cooler
Pull out the power plug, and the Beverage Cooler will be turned off.
Stop Using Beverage Cooler
If you’re not going to use the Beverage Cooler for a long time:
1. Pull out power plug
2. Clean the Beverage Cooler
3. Open the door of Beverage Cooler.
- 14 -
Cleaning Beverage Cooler
You should do the following operation:
1. Pull out power plug or disconnect the protecting device!
2. Scrub the sealing parts of the door only with clean water and soon wipe the
water off thoroughly.
3. Please clean the Beverage Cooler with slightly warm water and a little
detergent agent. Do not splash water to the operation control element or the
lighting system on the glass door.
4. Reconnect the Beverage Cooler with power source and then connect it with
power source after it has been cleaned.
Hints
Do not use detergent agent or solvent containing sands or acid.
Please regularly clean the scupper, so the dew can be discharged. You can
use small stick or similar objects to clean the scupper.
Energy Saving
Please place the Beverage Cooler in dry and ventilated room! The
Beverage Cooler should not be placed on the location where can be
directly irradiated by sunshine or where is close to heating sources, such
as: heating radiator or cooking stove, etc. If necessary, you can use
heating insulation board.
Try to shorten the opening time o f door o f Beverage Cooler!
First let beverage cool down and then place the beverage into Beverage
Cooler!
·Try not to open the d oor too often, esp ecial ly when the w eath er i s w et or hot.
Once you open the door, mind to close it as soon as possible.
- 15 -
Operation Noise
Normal Noise
Hum – the noise is cause by operation of the refrigeration unit.
Coo, rumbling or gurgle – the noise is caused by flow of cooling agent in the
pipeline.
Noise that can be removed easily
The noise caused by unevenness of placement of Beverage Cooler
You can use gradienter to correct and level the Beverage Cooler. You can use
screw leg to level it or you can plac e mat un der the Beverage C ooler to level it.
The noise generated when the Beverage Cooler leans against ot h er fur ni tur e.
Move the Beverage Cooler away from the furniture or equipment, against
which the Beverage Cooler leans.
The noise caused by mutual touch of vessels
Slightly separate the bottles or vessels from each others
Troubleshooting By Yourself
Before you call the after-sales service phone number, please check if you are
able to remove the failures according to the following hints.
Failures Possible Causes Remediation Measures
Temperature is quite
different from setting
value
Sometimes, the problem
can be removed if you
just turn off power of the
Beverage Cooler for 5
minutes and then restart
it.
If the temperature is too
high, you can check it
several hours later to
see if the temperature is
consistent with the
- 16 -
setting value.
If the temperature is too
low, you can check the
temperature again in the
next day.
The inside of Beverage
Cooler is not cold
You open the door of
Beverage Cooler very
often;
You place too many
beverage bottles in it
Reduce the frequency to
open the door of
Beverage Cooler.
Wait for 4 – 5 hours.
The Beverage Cooler
doesn’t cool down
The Beverage Cooler is
disconnected with power
source of the power
supply has stopped; the
power plug is not
inserted firmly
Press POWER button;
Check if power supply is
connected.
LED lamp is not on
LED lamp is damaged
Please contact the local
after-sales service
personnel for repair
Glass door have
congealed dew
Indoor temperature and
humidity is too
high, temperature of
Beverage Cooler was
set too lower.
Properly turn up the
setting temperature of
Beverage Cooler, while
dry off dew on the glass
door
Loading...