Midea R51I5/BG(C)E, R51I7/BG(C)E, R51I8/BG(C)E, R51I6/BG(C)E, R51I9/BG(C)E User Manual
...
CS406-R51E
2205509357
AIR CONDITIONER
REMOTE CONTROLLER ILLUSTRATION
Thank you very much for purchasing our air conditioner.
Please read this owner's manual carefully before using
your air conditioner.
11
2
3
4
6
7
7
7
8
8
9
12
Handling the remote controller ......................................................
Remote controller Specifications...................................................
Function buttons .................. .........................................................
Indicators on LCD ..........................................................................
How to use the buttons .................................................................
Auto operation.................................................................................
Cooling/Heating/Fan operation......................................................
Dehumidifying operation ...............................................................
Swing operation..............................................................................
Timer operation...............................................................................
ECONOMY operation ....................................................................
CONTENTS
Use the remote controller within a distance of 8
meters from the appliance, pointing it towards the
receiver. Reception is confirmed by a beep.
Location of the remote controller.
8m
CAUTIONS
The air conditioner will not operate if curtains, doors or other materials
block the signals from the remote controller to the indoor unit.
Prevent any liquid from falling into the remote controller. Do not expose
the remote controller to direct sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct
sunlight, the air conditioner may not function properly. Use curtains to
prevent the sunlight from falling on the receiver.
If other electrical appliances react to the remote controller. either move
these appliances or consult your local dealer.
The remote controller is powed by two dry
batteries(R03/LR03X2) housed in the rear
part and protected by a cover.
(1) Remove the cover by pressing and sliding off.
(2) Remove the old batteries and insert the new
batteries,placing the(+) and (-) ends correctly.
(3) Reattach the cover by sliding it back into
position.
NOTE: When the batteries are removed, the
remote controller erases all programming.
After inserting new batteries, the remote
controller must be reprogrammed.
Replacing batteries
.
Handling the remote controller
22
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
SWING
TIMER ON
ECONOMY
ON/OFF
TIMER
OFF
RESET
LOCK
SET T
EMPE
RATU
RE( C)
FO
LLOW
ME
LE
D
DISP
LAY
ION
TURBO
Model
Lowest Voltage of
CPU Emitting Signal
Rated Voltage
R51I7/BG(C)E, R51I8/BG(C)E,
-5 C 60 C( )
8m (when using 3.0 voltage,
it Gets 11m)
3.0V(Dry batteries R03/LR03 2)
2.0V
~~
Remote Controller Specification
1. Operating Mode: AUTO, COOL, DRY, HEAT(Cooling only
model without), and FAN.
2. Timer Setting Function in 24 hours.
OO
3. Indoor Setting Temperature Range : 17 C~30 C(62 F~88 F).
4. Full function of LCD (Liquid Crystal Display)
5. Back light emitting.
Environment
Signal Receiving
Range
Performance Feature
R51I9/BG(C)E;
Function buttons
CAUTIONS
Do not mix old and new batteries or batteries of a different type.
Do not leave the batteries in the remote controller if it is not going
to be used for 2 or 3 months.
Dispose of the old batteries in the special containers to be found
in the sales outlets.
1
TEMP UP Button
Push this button to increase the indoor temper-
oo
ature setting in 1 C(2 F) increments to 30 C(88 F).
2
TEMP DOWN Button
Push this button to decrease the indoor temper-
oo
ature setting in 1 C(2 F) increments to 17 C(62 F).
Model: R51I5/BG(C)E,
R51I6/BG(C)E,
R51I7/BG(C)E,
R51I8/BG(C)E.
ION and FOLLOW button:
Optional function.
Each time the button is pressed, the operation
mode is selected in the sequence of the following:
3
MODE Button
33 44
TEMP
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
SWING
TIMER ON
ECONOMY
ON/OFF
TIMER OFF
RESET LOCK
1
2
4
5
6
3
8
7
9
10
11
12
13
SET TEMPERATURE( C)
FOLLOW
ME
LED
DISPLAY
14
ION
TURBO
15
4
SWING Button
Used to stop or start louver movement and
set the desired up/down airflow direction.
When push this button, the ion generator is
energized and will help to remove pollen and
impurities from the air.
5
ION Button(Optional)
6
FOLLOW ME Button(Optional)
Push this button to initiate the Follow Me
function, the remote controller begins to detect
the actual temperature at its location. The
remote controller will send this signal to the
air conditioner every 3 minutes interval until
press the Follow Me button again. The air
conditioner will beep to indicate the Follow Me
feature has ended if it does not receive the
signal during any 7 minute interval.
7
RESET Button
Once the recessed RESET button is pressed,
all of the current settings will be cancelled
and the controller will return to the initial settings.
8
ON/OFF Button
Operation starts when this button is pressed
and stops when the button is pressed again.
NOTE: Heat mode is for Cooling & Heating models only.
AUTO
COOL
DRY
HEAT FAN
Used to select the fan speed in four steps:
Auto Low Med High
FAN SPEED Button
10
TIMER ON Button
9
Press this button to activate the Auto-on time
setting. Each press will increase the time setting
R51I10/BG(C)E, R51I11/BG(C)E,
R51I12/BG(C)E;
OO
-41 F~140 F
NOTE:
Temperature setting display:
Celsius scale( C):
Fahrenheit scale( F):
R51I5/BG(C)E, R51I6/BG(C)E,
R51I9/BG(C)E;
R51I10/BG(C)E, R51I11/BG(C)E,
R51I12/BG(C)E.
R51I5/BG(C)E, R51I6/BG(C)E,
R51I7/BG(C)E, R51I8/BG(C)E,
Loading...