Midea CS369-R51I4, R51I4/BGE, R51I4/BGCE, R51I19/BGE, R51I19/BGCE Owner's Manual

CS369-R51I4

2200019089

OWNER'S MANUAL

AIR CONDITIONER

REMOTE CONTROLLERILLUSTRATION

Thank youvery much forpurchasing our airconditioner.
Please readthis owner's manualcarefully before using
your airconditioner.

1

2

2

5

6

7

7

8

11

12

12

13

Handling the remote controller ...................................

Remote controller specification...................................

Features of remote controller buttons .......................

Indicators on display panel...........................................

AUTO operation............................................................

COOL/HEAT/FAN operation.......................................

DRY operation.... .........................................................

TIMER operation........................................................

SLEEP button function.............................................

RESET and LOCK buttons function............................

DIRECTION/SWING button function.........................

Cautions....................................................................

CONTENTS

Keep the remote controller where its
signals can reach the receiver of the
indoor unit. (a distance of 8m is allowed).
When you select the timer operation, the
remote controller automatically transmits
a signal to the indoor unit at the specified
time.
If you keep the remote controller in a
position that hinders proper signal
transmission, a time lag of up to 15
minutes may occur.

Location of the remote controller.

8m

CAUTIONS

The air conditioner will not operate if curtains, doors or other
materials block the signals from the remote controller to the indoor
unit.
Prevent any liquid from falling into the remote controller. Do not
expose the remote controller to direct sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct
sunlight, the air conditioner may not function properly. Use curtains
to prevent the sunlight from falling on the receiver.
If other electrical appliances react to the remote controller. either
move these appliances or consult your local dealer.

The remote controller uses two
alkaline dry batteries (R03/LR03X2)
(1) Slide the cover of the battery

compartment off according to the
arrow direction, then replace the
old batteries with new ones.

(2) Insert the new batteries making

sure that the(+) and (-) of battery
are installed correctly.

(3) Reattach the cover by sliding it

back into position.

Do not use old batteries or different
type batteries or rechargeable
batteries, otherwise it may cause the
remote controller malfunction.

NOTE:

Replacing batteries

.

Handling the remote controller

T
E
M

P

A
U
T

O
C
O
O
L

D
R
Y
H
E
A
T

FA
N
H
IG

H
M
E
D
L
O
W

M
O
D
E

FA

N

S
P
E

E

D
T
IM

E
R
O

N

S
LE

EP

O

N
/O

F
F

P
L
A

S
M
A

T
I
M
E

R
O

F
F

A
I
R

D

I
R
E

C
T
I
O

N

R

E
S
E
T
L

O
C
K

S

E
T
T

E
M

P

E

R

A
T
U

R
E
(

)

S

E
N
S
O

R

LED
DISPLAY

T
U
R

B
O

V
E
N
T

1

2

3

TEMP Button : Push this button to decrease the indoor
temperature setting in 1 C increments to 17 C.

oo

RESET Button: Once the recessed RESET button is pressed,
all of the current settings will be cancelled and the controller will
return to the initial settings.

NOTE: Heat mode is for cooling & heating models only.

1

6

ON/OFF Button: Press this button to start the indoor unit.

Press again to stop the unit.

9

TEMP Button : Push this button to increase the indoor

temperature setting in 1 C increments to 30 C.

oo

2

7

MODE Button: Each time the button is pressed, the operation

mode is selected in the sequence of the following:

3

AUTO

COOL

DRY

HEAT

FAN

FAN SPEED Button: Press the button to select the Fan speed in
the sequence: AUTO, LOW, MED and HIGH. Each time the button

is pressed, the fan speed selection is shifted.

5

4

10

8

SELF CLEAN(AUTO CLEAN )Button: Press this button under

COOL or DRY mode, the self clean function is activated. Press it
again will stop the operation and turn off the unit.

DIRECTION/SWING Button: Press this button once and quickly
to change the air flow direction of the horizontal louver a little.
The moving angle of the louver is 6 for each press. Press the
button without releasing for 2 more seconds, the horizontal louver
would swing automatically. Press it again, it would stop moving.
When the louver swing/moving at a certain position which would
affect the cooling and heating effect of the air conditioner, it would
automatically change the swing direction (upward or downward).

o

Model

Lowest Voltage of
CPU Emitting Signal

Rated Voltage

R51I4/BGE,R51I4/BGCE, R51I19/BGE, R51I19/BGCE

-5 C 60 C

8m (when using 3.0 voltage, it Gets 11m)

3.0V(Dry batteries R03/LR03 2)

2.0V

~

Remote Controller Specification

Performance Features

Features of Remote controller buttons

1. Operating Mode: COOL,HEAT(Cooling only model without),
DRY,FAN and AUTO .

2. Timer Setting Function in 24 hours.

3. Indoor Setting Temperature Range : 17 C~30 C.

4. Full function of LCD (Liquid Crystal Display)

ADJUST

AUTO
COOL
DRY
HEAT

FAN
HIGH
MED
LOW

MODE

FAN SPEED

DIRECTION
/SWING

TIMER ON

SLEEP

ON/OFF

TIMER OFF

SELF

CLEAN

RESET LOCK

1

2

4

5

6

3

8

7

9

10

11
12

13

Environment

SET TEMPERATURE( C)

FOLLOW

ME

LED

DISPLAY

14

Signal Receiving
Range

CLEAN

AIR

TURBO

15

16

CLEAN AIR Button(on some models): When push this button,
the Ionizer/Plasma Dust Collector(depending on models) is ener­gized and will help to remove pollen and impurities from the air.

FOLLOW ME Button(on some models): Push this button to
initiate the Follow Me feature, the remote display is actual
temperature at its location. The remote control will send this
signal to the air conditioner every 3 minutes interval until press
the Follow Me button again. The air conditioner will beep to
indicate the Follow Me feature has ended if it does not receive
the signal during any 7 minute interval.

Optional button

TIMER OFF Button: Press this button to activate the Auto-off time
setting. Each press will increase the time setting in 30 minutes
increments if the setting time is lower than 10 hours. When the
setting time reaches 10h, each press will increase the time setting
1 hour in increments. To cancel the Auto-off time setting, just press
the button until the time setting is 0.0.

LED DISPLAY Button: Press this button to clear the display on
the indoor unit, press it again to light the display .

LOCK Button: Press this recessed button to lock all current
settings, and the remote controller will not accept any operation
except that of the LOCK. Use the LOCK mode when you want to
prevent settings from being changed accidentally. Press the LOCK
button again to cancel the LOCK function. A lock symbol will appear
on the remote controller display when the lock function is activated.

TURBO Button:

Note:

Push this button to activate the Turbo function
which enables the unit to reach the preset temperature in the
shortest tiime. When press this button on cooling mode, the unit
will blow strong cooling air with super high fan speed. When press
this button on heating mode(applicable to the unit adopts PTC
only), the PTC will be energized and bring fast heating operation.

The unit system will automatically revert back to the
previous settings after continue operating under powerful
cooling mode for about half an hour.

13

16

14

15

TIMER ON OFF

SETTEMPERATURE

Transmission Indicator

Temp./Timer display

Fan speed display

Mode display

ON/OFF display

This transmission indicator will light
when remote controller transmits
signals to the indoor unit.

Displays the current selected mode.
Including AUTO, COOL, DRY, HEAT
(cooling & heating models only) and
FAN.

The temperature setting (from 17 C
to 30 C) or timer setting (0~24h) will
be displayed. If FAN mode is
selected, there will be no display.

o

o

This indicator will be displayed when

the unit is operating.

Displays the selected fan speed:
AUTO, HIGH,

when the fan speed
is selected in AUTO speed. When
AUTO or DRY Mode is selected, there

will be no signals displayed.

MED and LOW.

Nothing displays

This display area shows the settings
of the TIMER. That is, if only the
Auto-on time function is set, it will
display TIMER ON. If only the Auto-off
time function is set, it will display
TIMER OFF. If both functions are
set, it will display TIMER ON OFF
which indicates you have chosen both
the Auto-on time and Auto-off time.

LOCK display is displayed when
pushing the LOCK button. Push the
LOCK button to clear display.

4

5

Mode display(FAN mode)

FOLLOW ME display

When pressing FOLLOW ME button
in COOL or HEAT mode, the remote
sensing function is activated and this
indicator displays.

TIMER display

LOCK Indicator

11

TIMER ON Button: Press this button to activate the Auto-on time

setting. Each press will increase the time setting in 30 minutes
increments if the setting time is lower than 10 hours. When the
setting time reaches 10h, each press will increase the time setting
1 hour in increments. To cancel the Auto-on time setting, just
press the button until the time setting is 0.0.

NOTE: While the unit is running under SLEEP mode, it would

be cancelled if any other buttons are pressed.

SLEEP Button: Press this button to activate the Energy-Saving
mode. Press again to stop the function. This function is available
on COOL, HEAT or AUTO mode only and maintain the most
comfortable temperature for you.

12

Indicators on display panel

Ensure the unit is plugged in and power
is available. The OPERATION indicator
on the display window of the indoor unit
illuminates.

1. Mode select button (MODE)
Press to select AUTO.

2. Temperature button (TEMP)
Set the desired temperature. Normally,
set it between 21 C and 28 C.

3. ON/OFF button
Press the ON/OFF button to start
the air conditioner.

oo

ON/OFF button
Push this button again to stop the air
conditioner.
If the AUTO mode is uncomfortable,
you can select the desired conditions
manually.
When you select the AUTO mode, you
do not have to set the fan speed. The
fan speed will be automatically
controlled.

When you set the air conditioner in AUTO
mode, it will automatically select cooling,
heating (Cooling & Heating models only),
or health operation depending on what
temperature you have selected and the
room temperature.
Once you select the operating mode,

the operating conditions are saved in
the unit's microcomputer memory.
Thereafter, the air conditioner will start
operating under the same conditions
when you simply push the ON/OFF
button of the remote controller.

Start

Stop

2

1

3

Ensure unit is plugged and power is available.

1. Mode select button (MODE)
Press to select COOL, HEAT (Cooling &
Heating models only), or FAN mode.

2. Temperature button (TEMP)
Set the desired temperature, the most
comfortable temperature is between 21 C
and 28 C.

3. Fan speed button (FAN SPEED)
Press to select "AUTO", "LOW", "MED"
and "HIGH".

4. ON/OFF button
Press the ON/OFF button to start the air
conditioner. The OPERATION indicator
on the display panel of the indoor unit
illuminates. The operating mode is selected
in accordance with the room temperature
and operation starts after approximately 3
minutes (If you select FAN mode, the
unit will start immediately).

o

o

ON/OFF button
Push this button again to stop the air
conditioner.

Ensure unit is plugged and power is available.
The OPERATION indicator on the display
panel of the indoor unit starts flashing.

1. Mode select button (MODE)
Press to select DRY.

2. Temperature button (TEMP)
Push the "TEMP" button to set the desired
temperature.

3. ON/OFF button
Press the ON/OFF button to start the air
conditioner. No fan speed indicator displays.
The Indoor fan speed will be automatically
selected LOW.

Start

Stop

Start

The temperature cannot be controlled under FAN only mode.
While in this mode, only steps 1, 3 and 4 may be performed.

NOTES:

6

7

3

ADJUST

AUTO
COOL
DRY
HEAT

FAN
HIGH
MED
LOW

MODE

FANSPEED

TIMERON

SLEEP

ON/OFF

TIMEROFF

SELF
CLEAN

RESETLOCK

SETTEMPERATURE( C)

FOLLOW

ME

LED

DISPLAY

CLEAN

AIR

TURBO

2

1

4

ADJUST

AUTO
COOL
DRY
HEAT

FAN
HIGH
MED
LOW

MODE

FANSPEED

TIMERON

SLEEP

ON/OFF

TIMEROFF

SELF

CLEAN

RESETLOCK

SETTEMPERATURE( C)

FOLLOW

ME

LED

DISPLAY

CLEAN

AIR

TURBO

2

1

3

ADJUST

AUTO
COOL
DRY
HEAT

FAN
HIGH
MED
LOW

MODE

FANSPEED

TIMERON

SLEEP

ON/OFF

TIMEROFF

SELF
CLEAN

RESETLOCK

SETTEMPERATURE( C)

FOLLOW

ME

LED

DISPLAY

CLEAN

AIR

TURBO

Auto operation

COOL/HEAT/FAN operation

DRY operation

DIRECTION
/SWING

DIRECTION
/SWING

DIRECTION
/SWING

In DRY mode, due to the temperature difference between the setting temperature
and the actual indoor temperature, the unit will automatically operate in COOL or
FAN mode.

To press the TIMER ON button can set the auto-on
time of the unit. To press theTIMER OFF button
can set the auto-off time of the unit.

1. Press the TIMER ON button. The remote
controller shows TIMER ON, the last Auto-on
setting time and the signal "h" will be shown on
the LCD display area. Now it is ready to
reset the Auto-on time to START the operation.

2. Push the TIMER ON button again to set desired

Auto-on time. Each time you press the button,
the time increases by half an hour between 0
and 10 hours and by one hour between 10 and
24 hours.

3. After setting the TIMER ON ,there will be a one-

half second delay before the remote controller
transmits the signal to the air conditioner. Then,
after approximately another 2 seconds, the
signal "h" will disappear and the set temperature
will re-appear on the LCD display window.

To set the Auto-on time.

To set the Auto-off time.

1. Press the TIMER OFF button. The remote
controller shows TIMER OFF, the last Auto-off
setting time and the signal "h" will be shown on
the LCD display area. Now it is ready to
reset the Auto-off time to START the operation.

2. Push the TIMER OFF button again to set desired
Auto-off time. Each time you press the button,
the time increases by half an hour between 0
and 10 hours and by one hour between 10 and
24 hours.

3. After setting the TIMER OFF ,there will be a one­half second delay before the remote controller
transmits the signal to the air conditioner. Then,
after approximately another 2 seconds, the
signal "h" will disappear and the set temperature
will re-appear on the LCD display window.

When you select the timer operation, the remote controller automatically
transmits the timer signal to the indoor unit for the specified time.
Therefore, keep the remote controller in a location where it can transmit
the signal to the indoor unit properly.
The effective operation time set by the remote controller for the timer
function is limited to the following settings: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0,

3.5, 4.0, 4.5, 5.0, 5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13,
14, 15,16,17, 18, 19, 20, 21, 22, 23 and 24.

CAUTION

!

Example of timer setting

TIMER ON

Start

Off

6 hours later

(Auto-on Operation)

The TIMER ON feature is useful
when you want the unit to turn on
automatically before say when you
return home. The air conditioner will
automatically start operating at the
set time.

To start the air conditioner in 6 hours.

1. Press the TIMER ON button, the
last setting of starting operation
time and the signal

2. Press the TIMER ON button to
display "6:0h" on the TIMER ON
display of the remote controller.

3.

"h" will show

on the display area.

Wait for 0.5 second and the

TIMER ON indicator stops flashing

and this function is activated. The
digital display area will show the
temperature again.

TIMER ON

Example:

h

Set

ON/OFF button
Push this button again to stop the air conditioner.

Stop

Note: The fan speed cannot be adjusted when the unit is in AUTO and

DRY mode.

8

9

1

ADJUST

AUTO
COOL
DRY
HEAT

FAN
HIGH
MED
LOW

MODE

FANSPEED

TIMERON

SLEEP

ON/OFF

TIMEROFF

SELF
CLEAN

RESETLOCK

SETTEMPERATURE( C)

FOLLOW

ME

LED

DISPLAY

CLEAN

AIR

TURBO

1

ADJUST

AUTO
COOL
DRY
HEAT

FAN
HIGH
MED
LOW

MODE

FANSPEED

TIMERON

SLEEP

ON/OFF

TIMEROFF

SELF
CLEAN

RESETLOCK

SETTEMPERATURE( C)

FOLLOW

ME

LED

DISPLAY

CLEAN

AIR

TURBO

TIMER operation

DIRECTION
/SWING

DIRECTION
/SWING

11

10

TIMER OFF

Stop

On

Set 10 hours later

(Auto-off Operation)

The TIMER OFF feature is useful when
you want the unit to turn off automatically
after you go to bed. The air conditioner
will stop automatically at the set time.

To stop the air conditioner in 10 hours.

1. Press the TIMER OFF button, the last
setting of stopping operation time and
the signal "h" will show on the display
area.

2. Press the TIMER OFF button to display
"10h" on the TIMER OFF display of
the remote controller.

3. Wait for 0.5 second and the TIMER OFF
indicator stops flashing and this function
is activated. The digital display area will
show the temperature again.

TIMER OFF

Example:

h

TIMER ON OFF

h

On

Stop

2 hours later
after setting

Set

To stop the air conditioner 2 hours after
setting and start it again 10 hours after
setting.

1. Press the TIMER OFF button.

2. Press the TIMER OFF button again to
display 2.0h on the TIMER OFF display.

3.

4. Press the TIMER ON button again to
display 10h on the TIMER ON display .

5. Wait for the remote control to display
the setting temperature.

Press the TIMER ON button.

TIMER OFF TIMER ON
(On Stop Start operation)
This feature is useful when you want to
stop the air conditioner after you go to bed,
and start it again in the morning when you
wake up or when you return home.

Example:

COMBINED TIMER

(S both ON and OFF

)

etting timers

simultaneously

Start

Example:

TIMER ON TIMER OFF
(Off Start Stop operation)
This feature is useful when you want to start
the air conditioner before you wake up and
stop it after you leave the house.

To start the air conditioner 2 hours after
setting, and stop it 5 hours after setting.

1. Press the TIMER ON button.

2. Press the TIMER ON button again to
display 2.0h on the TIMER ON display.

3. Press the TIMER OFF button.

4. Press the TIMER OFF button again to
display 5.0h on the TIMER OFF display .

5. Wait for the remote control to display
the setting temperature.

Off

Stop

Start

10 hours later
after setting

TIMER ON OFF

h

2 hours later
after setting

2 hours later
after setting

Set

The timer setting(TIMER ON or TIMER OFF) that in sequence occurs
directly after the set time will be activated first.
If the same time is set for both TIMER ON and TIMER OFF settings, no
timer operation is performed. The air conditioner may stop operating,
either immediately or after approximately 10 minutes.

CAUTION

!

1

When you press the SLEEP button, the
economic running function will be activated.
During Cooling, Heating or AUTO operation,
the set temperature of the air conditioner
will automatically increase or decrease 1 C
per hour for 2 hours. After 2 hours, the set
point will continue at that temperature and
the fan motor will be set to LOW speed.
The sleep mode function can maintain the
most comfortable temperature and save
more energy for you.
NOTE: The SLEEP function is only available

under Cooling, Heating and AUTO
operation.

o

ADJUST

AUTO
COOL
DRY
HEAT

FAN
HIGH
MED
LOW

MODE

FANSPEED

TIMERON

SLEEP

ON/OFF

TIMEROFF

SELF
CLEAN

RESETLOCK

SETTEMPERATURE( C)

FOLLOW

ME

LED

DISPLAY

CLEAN

AIR

TURBO

SLEEP button function

DIRECTION
/SWING

1

1. When you press the recessed LOCK button,
all current settings are locked in and remote
controller does not accept any operation
except that of the LOCK.
Use the LOCK mode when you want to pre­vent settings from being changed accidentally.
Press the LOCK button again when you want
to cancel the LOCK mode.

A lock symbol will appear on the bottom right

hand side of the remote controller display
when the LOCK function is activated.

2. When you press the recessed RESET button,
all current settings are cancelled and return
to original factory settings.

2

Use the DIRECTION/SWING button to
activate AUTO swing function and lock
louver in desired position.

1. When press this button once and quickly,
the air flow direction setting feature of
the louver is activated. The moving
angle of the louver is 6 for each press.
Keep pressing the DIRECTION/SWING
button to move the louver to the desired
position.

2. When press the button without releasing
for 2 more seconds, the auto swing
feature of the louver is activated. The
horizontal louver would swing automa­tically. Press it again to stop.

When the louver swing or move to
a position which would affect the
cooling and heating effect of the air
conditioner, it would automatically
change the swing/moving direction
(upward or downward).

o

NOTE:

1

12

13

Cautions

1. When replacing batteries, do not use old batteries or different type
batteries. Otherwise it may cause the remote controller to malfunction.

2. If you do not use the remote controller for a few weeks or more, remove
the batteries. Otherwise, battery leakage may damage the remote
controller.

3. The average battery life during normal use is approximately half a year.
Replace the batteries when there is no receiving beep from the indoor
unit or if the transmission indicator on the remote controller fails to light.

4. Be sure there are no barriers between the remote controller and the receiver
of indoor unit otherwise the air conditioner will not work.

5. Keep the Remote Controller away from all liquids.

6. Protect the Remote Controller from high temperatures and exposure to
radiation.

7. Keep the indoor receiver out of direct sunlight or the Air Conditioner may
malfunction.

8. Keep controller away from EMI (Electro-Magnetic Interference) supplied by
other household appliances.

ADJUST

AUTO
COOL
DRY
HEAT

FAN
HIGH
MED
LOW

MODE

FANSPEED

DIRECTION
/SWING

TIMERON

SLEEP

ON/OFF

TIMEROFF

SELF
CLEAN

RESETLOCK

SETTEMPERATURE( C)

FOLLOW

ME

LED

DISPLAY

CLEAN

AIR

TURBO

ADJUST

AUTO
COOL
DRY
HEAT

FAN
HIGH
MED
LOW

MODE

FANSPEED

TIMERON

SLEEP

ON/OFF

TIMEROFF

SELF
CLEAN

RESETLOCK

SETTEMPERATURE( C)

FOLLOW

ME

LED

DISPLAY

CLEAN

AIR

TURBO

RESET and LOCK buttons funciton

DIRECTION/SWING button function

DIRECTION
/SWING