Midea CS369-R51I4, R51I4/BGE, R51I4/BGCE, R51I19/BGE, R51I19/BGCE Owner's Manual
CS369-R51I4
2200019089
OWNER'S MANUAL
AIR CONDITIONER
REMOTE CONTROLLERILLUSTRATION
Thank youvery much forpurchasing our airconditioner.
Please readthis owner's manualcarefully before using
your airconditioner.
1
2
2
5
6
7
7
8
11
12
12
13
Handling the remote controller ...................................
Remote controller specification...................................
Features of remote controller buttons .......................
Indicators on display panel...........................................
AUTO operation............................................................
COOL/HEAT/FAN operation.......................................
DRY operation.... .........................................................
TIMER operation........................................................
SLEEP button function.............................................
RESET and LOCK buttons function............................
DIRECTION/SWING button function.........................
Cautions....................................................................
CONTENTS
Keep the remote controller where its
signals can reach the receiver of the
indoor unit. (a distance of 8m is allowed).
When you select the timer operation, the
remote controller automatically transmits
a signal to the indoor unit at the specified
time.
If you keep the remote controller in a
position that hinders proper signal
transmission, a time lag of up to 15
minutes may occur.
Location of the remote controller.
8m
CAUTIONS
The air conditioner will not operate if curtains, doors or other
materials block the signals from the remote controller to the indoor
unit.
Prevent any liquid from falling into the remote controller. Do not
expose the remote controller to direct sunlight or heat.
If the infrared signal receiver on the indoor unit is exposed to direct
sunlight, the air conditioner may not function properly. Use curtains
to prevent the sunlight from falling on the receiver.
If other electrical appliances react to the remote controller. either
move these appliances or consult your local dealer.
The remote controller uses two
alkaline dry batteries (R03/LR03X2)
(1) Slide the cover of the battery
compartment off according to the
arrow direction, then replace the
old batteries with new ones.
(2) Insert the new batteries making
sure that the(+) and (-) of battery
are installed correctly.
(3) Reattach the cover by sliding it
back into position.
Do not use old batteries or different
type batteries or rechargeable
batteries, otherwise it may cause the
remote controller malfunction.
NOTE:
Replacing batteries
.
Handling the remote controller
T
E
M
P
A
U
T
O
C
O
O
L
D
R
Y
H
E
A
T
FA
N
H
IG
H
M
E
D
L
O
W
M
O
D
E
FA
N
S
P
E
E
D
T
IM
E
R
O
N
S
LE
EP
O
N
/O
F
F
P
L
A
S
M
A
T
I
M
E
R
O
F
F
A
I
R
D
I
R
E
C
T
I
O
N
R
E
S
E
T
L
O
C
K
S
E
T
T
E
M
P
E
R
A
T
U
R
E
(
)
S
E
N
S
O
R
LED
DISPLAY
T
U
R
B
O
V
E
N
T
1
2
3
TEMP Button : Push this button to decrease the indoor
temperature setting in 1 C increments to 17 C.
oo
RESET Button: Once the recessed RESET button is pressed,
all of the current settings will be cancelled and the controller will
return to the initial settings.
NOTE: Heat mode is for cooling & heating models only.
1
6
ON/OFF Button: Press this button to start the indoor unit.
Press again to stop the unit.
9
TEMP Button : Push this button to increase the indoor
temperature setting in 1 C increments to 30 C.
oo
2
7
MODE Button: Each time the button is pressed, the operation
mode is selected in the sequence of the following:
3
AUTO
COOL
DRY
HEAT
FAN
FAN SPEED Button: Press the button to select the Fan speed in
the sequence: AUTO, LOW, MED and HIGH. Each time the button
is pressed, the fan speed selection is shifted.
5
4
10
8
SELF CLEAN(AUTO CLEAN )Button: Press this button under
COOL or DRY mode, the self clean function is activated. Press it
again will stop the operation and turn off the unit.
DIRECTION/SWING Button: Press this button once and quickly
to change the air flow direction of the horizontal louver a little.
The moving angle of the louver is 6 for each press. Press the
button without releasing for 2 more seconds, the horizontal louver
would swing automatically. Press it again, it would stop moving.
When the louver swing/moving at a certain position which would
affect the cooling and heating effect of the air conditioner, it would
automatically change the swing direction (upward or downward).
o
Model
Lowest Voltage of
CPU Emitting Signal
Rated Voltage
R51I4/BGE,R51I4/BGCE, R51I19/BGE, R51I19/BGCE
-5 C 60 C
8m (when using 3.0 voltage, it Gets 11m)
3.0V(Dry batteries R03/LR03 2)
2.0V
~
Remote Controller Specification
Performance Features
Features of Remote controller buttons
1. Operating Mode: COOL,HEAT(Cooling only model without),
DRY,FAN and AUTO .
2. Timer Setting Function in 24 hours.
3. Indoor Setting Temperature Range : 17 C~30 C.
4. Full function of LCD (Liquid Crystal Display)
ADJUST
AUTO
COOL
DRY
HEAT
FAN
HIGH
MED
LOW
MODE
FAN SPEED
DIRECTION
/SWING
TIMER ON
SLEEP
ON/OFF
TIMER OFF
SELF
CLEAN
RESET LOCK
1
2
4
5
6
3
8
7
9
10
11
12
13
Environment
SET TEMPERATURE( C)
FOLLOW
ME
LED
DISPLAY
14
Signal Receiving
Range
CLEAN
AIR
TURBO
15
16
CLEAN AIR Button(on some models): When push this button,
the Ionizer/Plasma Dust Collector(depending on models) is energized and will help to remove pollen and impurities from the air.
FOLLOW ME Button(on some models): Push this button to
initiate the Follow Me feature, the remote display is actual
temperature at its location. The remote control will send this
signal to the air conditioner every 3 minutes interval until press
the Follow Me button again. The air conditioner will beep to
indicate the Follow Me feature has ended if it does not receive
the signal during any 7 minute interval.
Optional button
Loading...