13
TROUBLESHOOTING TIPS
Malfunctions
Unit does not
start
Unit not cooling
or heating
(Cooling/ heating
models only)
room very well
while air flowing
out from the air
conditioner
Cause
Power cut
Unit may have become
Unplugged.
Fuse may have blown.
Battery in Remote controller may
have been exhausted.
The time you have set with timer
is incorrect.
Wait for power to be restored.
Check that plug is securely in wall
receptacle.
Replace the fuse.
Replace the battery.
Wait or cancel timer setting.
Set temperature correctly. For
detailed method please refer to
"Using remote control" section.
Clean the air filter.
Close the doors or windows.
Clear obstructions away first, then
restart the unit.
Wait.
Inappropriate temperature
setting.
Air filter is blocked.
Doors or Windows are open.
Air inlet or outlet of indoor or
outdoor unit has been blocked.
Compressor 3 minutes
protection has been activated.
If the trouble has not been corrected, please contact a local dealer or the nearest customer
service center. Be sure to inform them of the detailed malfunctions and unit model number.
Notes: Do not attempt to repair the unit yourself.
Always consult an authorized service provider.
What should be done?
14
TROUBLE SHOOTING TIPS
Troubleshooting guide
8. Dripping water may generate on the surface of the indoor unit when cooling in a high
relatively humidity (relative humidity higher than 80%). Adjust the horizontal louver to
the maximum air outlet position and select HIGH fan speed.
9. Heating mode (For cooling and heating models only)
The air conditioner draws in heat from the outdoor unit and releases it via the indoor unit
during heating operation. When the outdoor temperature falls, heat drawn in by the air
conditioner decreases accordingly. At the same time, heat loading of the air conditioner
increases due to larger difference between indoor and outdoor temperature. If a
comfortable temperature can't be achieved by the air conditioner, we suggest you use a
supplementary heating device.
10. Auto-restart function
Power failure during operation will stop the unit completely.
For the unit without Auto-restart feature, when the power restores, the OPERATION indicator
on the indoor unit starts flashing. To restart the operation, push the ON/OFF button on the
remote controller. For the unit with Auto-restart feature, when the power restores, the unit
restarts automatically with all the previous settings preserved by the memory function.
7. The air conditioner runs function after turning off the unit.Anti-mildew
When turning off the unit under COOL(AUTO COOL, FORCED COOL) and DRY mode, the air
conditioner will run function for 7-10 minutes, Anti-mildew if turns off on HEAT mode, the unit will
continue operating for about 30 seconds at LOW fan speed, then stop the operation and turn
off the unit automatically. Under Anti-mildew operation, do not restart the air conditioner until the
unit is completely off.
Fuse blows frequently or circuit breaker trips
frequently .
Other objects or water fall into the air conditioner.
Terrible odors are smelled or abnormal sounds
are heard.
Trouble
OPERATION(RUN) indicator or other
indicators continue flashing.
If one of the following code appears on the
display area : E0,E1,E2,E3.....or P0,P1,P2,
P3...., or F1,F2,F3.......
The unit may stop operation or
continue to run in a safety condition
(depending on models). Waiting for
about 10 minutes, the fault may be
recovered automatically, if not,
disconnect the power and then
connect it in again. If the problem
still exists, disconnect the power and
contact the nearest customer service
center.
Stop the air conditioner immediately,
disconnect the power and contact the
nearest customer service center.
After 240 h ours of op eration , the indo or displa y window w ill disp lay and fla sh CL ,
this fe ature is a r eminder t o clean th e Air Filter fo r more effi cient op eratio n. After 15
secon ds, the sy stem will r evert ba ck to the pre vious di splay ag ain. When t he CL
indic ator app ears and fl ashes, p lease pre ss the LED b utton on r emote con trolle r
for 4 tim es or pres s the Manua l contro l button fo r 3 or more ti mes to cle ar the regi stered
hours , otherw ise the CL ind icator w ill displ ay and fla sh again fo r anothe r 15 secon ds at
the nex t time of st arting th e unit.
11. Cl eanin g filte r remin ding fu nctio n(Opt ional )
,
,
,
,
,
,
After 288 0 hours of o peratio n, the ind oor displ ay windo w will dis play and fl ash nF ,
this fe ature is a r eminder t o replac e the Air Filte r for more e fficien t operat ion. After 15
secon ds, the sy stem will r evert ba ck to the pre vious di splay ag ain. When t he nF
indic ator app ears and fl ashes, p lease pre ss the LED b utton on r emote con trolle r for 4
times o r press th e Manual co ntrol bu tton for 3 or m ore time s to clear t he regist ered hou rs,
other wise the n F indicat or will di splay and f lash aga in for ano ther 15 sec onds at th e
next ti me of star ting the un it.
12. R eplac ing fil ter rem indin g funct ion (Op tiona l)
,
,
,
,
,
,