2 in 1
MIDEA
Cordless Handstick
2 in 1
Cordless Handstick
PLEASE READ THE
MANUAL CAREFULLY
BEFORE USING AND
KEEP IT PROPERLY FOR
FUTURE USE
INSTALLATION
INSTRUCTIONS
USER GUIDE
Warning notices: Before using this product,
please read this manual carefully and keep
it for future reference. The design and
specifications are subject to change without
prior notice for product improvement.
Consult with your dealer or manufacturer
for details.
version 01
MVC-V18PR
STRUCTURE OF THE
01
Assembly and other parts instruction
PRODUCTV
Tube
Power
indicator
Body
Power
button
Brush
Power volume
Indicator
Power volume
Indicator
Mode
button
Mode
button
Max mode
Indicator
Power
button
Accessories list:
Crevice
Nozzle
Adaptor
Instruction
Manual
2 in 1 brush Turbo bed
brush
Storage
rack
Tips:
When cleaning the high places, please assemble the accessories on tube.
02
Operation 1:
Battery charging:
Tips:
Battery is not full when leaving factory, please remember to charge
up before first usage.
No. Operation instruction
1 Put the body on horizontal surface.
HOW TO USE
Connect the adaptor to charging port
on battery pack and plug the adaptor to socket.
When charing, power indicator will twinkle continuously.
1min after charging up, indicator will shut off。
2 Charging time：4-6h
Discharging time：Max Mode: ≥10Mins
Middle Mode: ≥20Mins
Low Model: ≥45Mins
Operation 2:
Cleaning:
Note:
To avoid the air flue being blocked, please clean the big particle
waste. (such as paper, cloth and others).
No. Operation instruction
1 Knob down “Power button” to start
2 Knob down “Power button” again to stop
3 When only one power indicator is on and twinkle, please
charge it.
Power
indicator
Power
button
Mode
button
Operation 3
Wall mount assembly and usage:
1. Wall mount assembly
When not using the cleaner, please store the cleaner on mount.
2. Choose the storage rack
1. Installation of the storage shelf: install the receiving buckle assembly
and the storage base as shown in the diagram, and place the installed
storage shelf assembly vertically on the horizontal surface as shown in t
he right picture;
2. Placement of the whole machine: Before placing the whole machine
on the storage rack components, please confirm again whether the
placement position is horizontal, and ensure that the whole machine has
been closed and stopped working. Gently place the whole machine on
the slot position of the storage rack as shown in the figure below, and
leave after the whole machine is placed smoothly.
Operation 4
Replace Battery
Tips:
1. Laypeople don’t disassemble battery please.
2. Battery must be replaced and repaired by professional
after-sales service personnel.
Operation 5
Clean and maintain cleaner
Dust cup disassembly and clean
Tips:
To keep the suction power of cleaner, please clean the dust in it
regularly.
1. Push the locker button, open the bottom cover and release dust
Press
Press
2. Knob down the dust cup release button, take down the cup
Push
3. Take out the cyclone from dust cup
4. Disassemble cyclone and clean, all parts are washable.
5. After airing all parts completely, assemble them according to
disassembly steps.
Operation 6
Clean and maintain motorized brush
Note:
1. To avoid affect the normal operation of brush, when roller brush
and wheels is entangled or dusty, please clean and maintain
them.
2. When disassemble and main brush, please make sure it’s not
working
1. Push button and take off the brush.
Push
2. Open the gland of brush, then take out the roller brush and clean，
After cleaning it completely, assemble them according to
disassembly steps.
Open the gland Take out roller brush
Tips:
Don’t suggest to wash the brush.
If the brush was tangled by hair, please scissor or knife to clean.
Loading...