TWIN TUB WASHING MACHINE
INSTRUCTION MANUAL
MODEL:
Please keep this manual for operation and maintenance of this washing machine.
MSW-1108P
CONTENTS
Structure Instruction
Name Of Parts
Accessories
Introduction Of Control Panel
Attention To Installation
Lay upper drain hose
Change the position of the drain hose
Installation site
Preparation Instructions
Weight reference of washing materials
Laundry volume and detergent
dosage reference
Washing Method
Soak Function
Rinsing Method
Spinning Method
Attention To Maintenance
Cabinet maintenance
Cleaning the lint filter
Anti-freezing protection
Operation when objects are
dropped into outside of the spin tub
Notes
Others
Main Technical Parameters
Packing List
Name Of Parts
1
Control panel
(For upper drain only)
1
1
2
Wash cover
Lint filter
Safety cover
2
2
2
3
wash tub
Pulsator
Cabinet
3
3
Base
4
4
4
Accessories
5
6
6
6
6
Introduction Of Control Panel
Water inlet
6
7
8
9
9
Water inlet
Wash timer
Wash timer
Wash timer
Wash timer
35
Soak
Inner spin cover
Wash selector -Drain
Normal
Heavy
Wash-Drain Selector
Wash selector -Drain
Normal
5
10
Heavy
15
Wash-Drain Selector
Water inlet hose
Spin timer
Spin timer
Drain
Spin timer
Spin timer
Drain
Drain hose
Spin cover
Frame
Power plug
Drain hose
(For lower drain only)
※ he drawing above is for reference only, specific drawing is subject to actual models.T
Water inlet: be used to inject water to wash tub or spin tub.
Wash timer: be used to select required washing time.
Spin timer: be used to select required spinning time.
Wash-Drain selector: For washing or rinsing, select “ Normal”or“ Heavy”.
For Draining ,select “Drain”.
1
Installation
Usage method
Attention To Installation
Needs a drain hose with minimum diameter 3 cm, and minimum carry away capacity of
40 liters per minute.
For upper drain system, the drain hose must be placed at least 86 cm(30 inches) from the
bottom of washer , but not higher than 100 cm.
86cm<H<100cm
Change the position of the drain hose
The ex-factory installation position of the drain
hose is located the spin side . According to the
installation site, the drain hose can also be installed
at the wash side of the machine . The method is
as follows:
Unplug the power cord and empty
water in the drain hose completely.
Spread a piece of soft cloth on the floor (e.g. a blanket)
and place the washing machine on it gently.
Take the drain hose out from the buckle
at the spin side, and put it into the buckle
at the wash side.
Hang up the drain hose kit.
In order to avoid electrical failure, discoloration and deformation, do not install the machine
in the following places:
Locations exposed
to direct sunlight
at
Lay upper drain hose
of
FOR UPPER DRAIN SYSTEM ONLY
FOR LOWER DRAIN SYSTEM ONLY
Installation site
Locations exposed to rain
or snow
Drain hose
Buckle
Locations with uneven
or unstable ground
Front
Blanket
Preparation Instructions
Plug in power and connect the water inlet hose.
Lay down the lower drain hose and connect it to the sewer , or lay the upper drain hose to places as indicated
2
in page .
Check that there are no objects such as coins, hairpins, mud or sand in the pocket.
Strings should be knotted in advance to prevent entanglement.
Clothes can be classified for washing according to the texture, dirty
For small pieces (e.g., stockings) or fluffy clothes, put them into
Attachment: Weight reference of washing materials
T-shirt (cotton)
about 150 g
Panties (cotton)
about 50 g
Shirt (blended)
about 200 g
Socks (blended)
about 50 g
Attachment :Laundry volume and detergent dosage reference
Fabric ty pe
Synth eti cs,s ilk ,
Delic ate f abric s
Cotto n or li nen
Heavy s oil s
Laundry
capacit y( kg )
0-5.0
5.0-6 .5
0-6.5
6.5-11.0
0-6. 5
6.5-11.0
Wat er
level
Low
Mid
Mid
High
Mid
High
Wat er flow
3
Norma l
Norma l
degree and color.
a nylon net for washing.
Was h time
(min ut es)
Heavy
10-35 (so ak 20)
Slipover (cotton)
about 500 g
Scarf (cotton)
about 300 g
3
3-5
7
7-10
10
Deterge nt
amount( g)
About
About
About
About
About
About
50
61
61
77
61
77
The dosage of washing detergent varies according to dirty degree and texture of laundries.
2
3
Usage method
Usage method
Washing Method
1. Insert the inlet hose into the , and choose injectingwater water inlet mouth
water to the wash tub
2.
Put the laundry into the wash tub, and add detergent into it.
When fill water to half of the desired water level, turn off the
water tap and let laundries soak in the solution for minutes,
then fill water to desired water level.
3. Set wash program “Normal” or “Heavy” as per amount and
texture of laundries.
4. Turn the wash timer knob to set wash time.
5. After washing, set the wash drain selector to “Drain” position for draining.
6. Buzzer will alarm the completion of washing.(For machines having buzzer function only)
Soak Function
For seriously stained clothes, Soak wash is useful to achieve better wash result.
15-35 minutes of the wash timer is for soak wash:(illustrate as follows)
Total: 35 (mins)
This machine can wash blended blanket (less than 3kg) marked with the "hand washing" label.
about 2
Work time
Static time
.
(For machines having soak function only )
35
about 5 about 5 about 5
about 1.5
about 1.5
Wash timer
Water level indicator
Wash timer
15
(unit： )mins
Soak
5
35
10
15
Washing method is as follows:
Dilute detergent with water (below 50℃), then pour the solution into
Fold the blanket as shown in the figure, and into the wash tub.
adequate the wash tub.
put it
Fold in half along
the long edge
1/3 fold in the
same direction
Roll up the blanket
Put into the tub with
blanket edge facing down
Rinsing Method
A. Spraying rinse (rinse in the spin tub)
Put the laundry into the spin tub after washing.
Turn on the water tap, choose to fill water into the spin tub for 3-4 minutes, and then turn off the water tap.
Set the spin timer for 2-5 minutes for rinsing.
The above steps can be repeated.
Note: If there is red rust in water, do not choose spraying rinse, for the rust is easy to adhere to laundries.
Ensure that do not fill water into spin tub when spinning.
B. Common rinse (rinse in the wash tub)
To save time, water and energy, can do pre-spinning before rinsing.
Put laundries which have already been dehydrated intothe wash tub.
After filling water to the desired level, turn off the water tap to save water.
Turn the “Wash-Drain selector” knob to the "Normal” or “Heavy”.
Set the “wash timer”to thedesired time (about 3-5 minutes)for rinsing.
After rinsing, put the washing materials into the spin tub to spin for
Drain out the rinsing water in the wash tub.
The above steps can be repeated.
1 to 5 minutes.
Spin timer
4
Spinning Method
1.Shake out the laundry and put
them into the spin tub.
2.Put the inner spin cover on .
Confirm the inner spin cover is placed
horizontally.
Inner
spin cover
Spin tub
Correct
3.Close the safety cover and the
spin cover.
cover
Spin
Safety
cover
The appliance can not be used by children or persons with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision or instruction.
Please do not use other water inlet hoses, except for the water inlet hoses that are supplied as the accessories.
If need to replace the hose, please buy it from the local service center.
When choose to inject water to wash tub or spin tub,water injecting is forbidden.
If strong vibration occurs in time of spinning, open the spin cover immediately. Make sure that
is placed on a flat and stable floor ,and then adjust washing materials, distribute them evenly.
To do spinning and draining together, please spin for 1 minute before draining.
Do not wash or spin waterproof clothes or clothes that float easily to avoid abnormal vibration or damage to the
clothes.
4.Refer to the following table to select
spinning time.
Washing materials
Wire
Light clothes
(fiber/blended)
Knitwear (fiber)
Underwear
(cotton)
Slipover
(cotton/linen)
Toweling coverlet
(cotton)
Spin time
About 50
seconds
About 1
minute
About 1～2
minutes
About 2～3
minutes
About 3～4
minutes
About 5
minutes
the laundry
Incorrect
Spin timer
the washing machine
5
Maintenance
Others
Attention To Maintenance
Cabinet maintenance
After using the washing machine , wipe
the moisture and stain on it with a
piece of soft cloth. To avoid damage
to the surface , do not use corrosive or
volatile chemicals.
To prevent from freezing:
Turn off the water tap, remove the water inlet hose and empty water in the water inlet
hose completely.
Lay the drain hose and turn the drain selector knob to the "Drain”position to
empty the water in the tub.
If the water is frozen, please take the following steps:
Put the water inlet hose into warm water of about 50℃.
Keep about 2 liters of warm water below 50℃ in the wash tub for
about 10 minutes. and then lay the drain hose and turn the
wash drain selector knob to the "Drain”position to empty the water .
Fit the water inlet hose and turn on the water tap to
confirm water filling and draining work properly.
Operation when objects are
dropped into the outside of the spin tub
Remove all screws on the frame with a screw driver.
Pull up the frame with both hands and turn it backwards.
Take out the clothes dropped into the outside of the spin tub.
Press the frame to reset and tighten screws.
1.Press the button head, and
pull the lint filter out.
Turn the filter net inside out, and rinse it
in water.
After inserting the claw, press the button
to insert it into place.
A sound of “ba” means proper installation.
Anti-freezing protection
Cleaning the lint filter
Button head
Claw
Frame
Cabinet
Notes
The washing machine employs alternative current with rated voltage and frequency . When voltage fluctuates
between -10% and 10% of the rated voltage, the machine can work normally.
Connection mode of the power cord of this machine is Y-shaped connection. Users
or reconnect the wire by themselves. please contact the designated service center.
After using, be sure to unplug the power plug.
Be sure to use plug that is properly grounded.
The maximum gradient of the supporting surface for the washing machine should not exceed 2º.
Do not tear down electrical wires and components in the machine by yourself.
There are holes on the base for ventilation. These holes should not be blocked by foreign objects (carpets, etc.).
Never connect the grounding wire with the live wire, or it may lead to an electric shock.
If the power cord is damaged, it must be replaced by a qualified person to avoid a hazard.
If this part needs to be repaired,
If the following symptoms occur, please disconnect the power plug and perform the following
checks:
Symptom
The washing
machine does
not work.
The drain hose
does not work.
There is abnormal
noise during washing.
There is abnormal
noise and violent
vibration during
spinning.
Check that the power supply is in good condition.
Check that the power plug is inserted properly.
Check that the wash timer knob or the spin timer knob is not
in the "0" position.
Check that the drain hose is not laid too high.
Check that the drain hose is not frozen.
Check that the drain hose is not blocked by foreign matter.
Check that there are no coins or any other foreign
objects dropped into the wash tub.
Check that the washing machine is placed on flat, stable floor.
Check that clothes are evenly distributed in the spin tub.
Check that there are no washing materials or foaming debris
dropped into the outside of the spin tub.
Reason
should not detach
After you use the washing machine, never forget to do the following two things:
1. Disconnect the power plug.
2. Remove the water inlet hose.
6
控制面板图案
控制面板图案
7
0thers
Parameters
Others
Do not open the spin cover
in time of spinning
If the spin cover is opened in time of
spinning ,the washing machine
will arrest at once , which will
shorten its service life . So avoid
opening the spin cover during
spinning.Furthermore , do not
put hands into the wash tub
while the machine running,
for it is very dangerous.
Avoid dampness
Do not put the washing machine in extreme
damp place, for dampness may weaken
insulation of the machine, which may lead to
electric shocks or faults.
Notes for scrubbing
In order to avoid damaging
electrical components , do
not scrub operation parts
of control panel with water.
Which can not be washed
Do not wash clothes that
are stained with paint,
petrol or other volatile or
flammable substance.
Do not forget to close
the inner spin cover
If laundries in the
spin tub are tossed out,
they are easily damaged.
Do not use warm water above 50℃
This will prevent plastic
deformation and aging.
Main Technical Parameters
Parameter
Function
Wash
Spin
Pump
Capacity
(dry Clothes)
11.0 kg
4.6kg
Power
Supply
240V
50Hz
PACKING LIST
Quantity
Accessories
Input Power
(lower drain)
420 W
160 W
Input Power
(upper drain)
420 W
160 W
/
Name
Water inlet hose
Instruction manual
Inner spin cover
30W
Maximum
Time
15 min.
3
5 min.
(soak wash)
5 min.
Water
volume
HI: 77L
H: 72L
M: 61L
L: 50L
/
Packing list
1 Set of washing machine
Quantity
1
1
1
/
Maximum water
pressure permitted
in the water inlet
0.6Mpa
Note
Overall dimension
(L X W X H)
870 x512x 957
(mm)
Net weight
23kg
Do not let children play near the tub
It's very dangerous
for children falling into
the tubs.
Be sure to comply with all the notes above.
Keep away from fire or heat source
Keep the washing machine away from
fire or heat source such as heater,
cigarette, etc. to avoid fire
accident or plastic
deformation.
8
9
Loading...