Washing Machine
OWNER’S MANUAL
MF W-7 52S
MF W-E C75 0
MF W-8 52S
MF W-9 52S
MF W-E C95 0
Read This Manual
Use all instructions and explanations of
the installation before use. Follow the
instructions carefully. Keep the operation
instructions handy for later use. If the
application is sold or passed on then ensure
that the new owner always receives those
operation instructions.
CONTENTS
SAFETY INSTRUCTIONS
Safety instructions ....................................................
INSTALLATION
Product description ..................................................
Installation area ......................................................
Unpacking the washing machine ...............................
Installation of drain hose ..........................................
Levelling the washing machine ...................................
Selection of tap .........................................................
Connection of inlet hose, tap and washing machine....
OPERATIONS
Preparation before washing.......................................
Washing ...................................................................
After washing............................................................
Washing matters needing attention ...........................
The usage of detergent and washing powder.............
Control pane .............................................................
Option......................................................................
Personalized setting of washing program....................
Operations of washing process....................................
Washing program table ........................................
Maintenances
Cleaning and care .....................................................
Cleaning the cabinet..................................................
Cleaning drain pump filter .........................................
Trouble shooting.......................................................
Technical information ................................................
2
8
9
9
9
10
11
11
12
12
12
13
13
14
15
16
16
17
18
18
19
20
21
1
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS
For your safety, the information in this manual must be followed
to minimize the risk of fire or explosion, electric shock, or to
prevent property damage, personal injury or loss of life.
• This appliance is not intended for use by persons(including
children) with reduced physical, sensory or mental capabilities
or lack of experience and knowledge unless they have
been given supervision or instruction concerning use of
the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not
•
play with the appliance.
If the supply cord is damaged, it must be replaced by the
•
manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
The new hose-sets supplied with the appliance are to be
•
used and that old hose-sets should not be reused.
• The openings must not be obstructed by a carpet.
• This appliance is intended to be used in household and similar
applications such as:
− staff kitchen areas in shops, offices and other working environments;
− farm houses;
− by clients in hotels, motels and other residential type environments;
− bed and breakfast type environments;
− areas for communal use in blocks of flats or in launderettes.
2
SAFETY INSTRUCTIONS
Model
MFW-752S
MFW-EC750
MFW-852S
MFW-952S
MFW-EC950
Washing Capacity
7.0kg
8.0kg
9.0kg
Standard Water Pressure
0.03MPa~0.8MPa
0.03MPa~0.8MPa
0.03MPa~0.8MPa
Explanation of the symbols:
Warning!
This combination of symbol and signal word indicates
a potentially dangerous situation which may result in
death or serious injuries unless it’s avoided.
Caution!
This combination of symbol and signal word indicates
a potentially dangerous situation which may result in
slight or minor injuries or damage to property and the
environment.
3
SAFETY INSTRUCTIONS
Note!
This combination of symbol and signal word indicates
a potentially dangerous situation which may result in
slight or minor injuries.
Warning!
The electric shock!
This appliance is for indoor use only.
•
Do not put washing machine at humid place.
•
• Hands shall not be inserted into running spin-dry tub .
• If the spin-dry tub does not stop within 15 seconds after
opening the cover , please stop using the machine and
have it repaired.
• Before any maintenance the device, unplug the appliance
from the mains.
• Always unplug the machine and turn off the water supply
after use. The max. inlet water pressure, in pascals. The
min. inlet water pressure, in pascals.
• To ensure your safety, power plug must be inserted into
an earthed three-pole socket. Check carefully and make sure
that your socket is properly and reliably earthed.
• Make sure that the water and electrical devices must be
connected by a qualified technician in accordance with the
manufacturer's instructions and local safety regulations.
4
SAFETY INSTRUCTIONS
Risk to children!
• EN countries: the appliance can be used by children aged
from 8 years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
• Animals and children may climb into the machine. Check
the machine before every operation.
• Young children should be supervised that they do not play
with the appliance.
• Machine may be very hot during the operation. Keep kids
and pets far away from the machine during the operation
very wet rooms as well as in the rooms with explosive or
caustic gas.
•
Remove all packages before using the appliance. Otherwise,
serious damage may result.
• The washing machine with single inlet valve only can be
connected to the cold water supply. The product
inlet valves should be correctly connected to the hot water
and cold water supply.
• Plug must be accessible after installation.
with double
Risk of explosion!
•
Do not wash or dry articles that have been cleaned in, washed
in, soaked in, or dabbed with combustible or explosive
substances( such as wax, oil, paint, gasoline, degreasers,
dry-cleaning solvents, kerosene, etc.) This may result in
fire or explosion.
Before hand thoroughly rinse items of washing by hand.
•
5
SAFETY INSTRUCTIONS
Caution
Installing the product!
• This washing machine is for indoor use only.
• It isn't intended to be built-in using.
• The openings must not be obstructed by a carpet.
• Washing machine shall not be installed in bath room or
very wet rooms as well as in the rooms with explosive
or caustic gases.
• Remove all packages and transport bolts before using
the appliance. Otherwise, serious damage may result.
• The washing machine with single inlet valve only can be
connected to the cold water supply. The product with
double inlet valves should be correctly connected to the
hot water and cold water supply.
• Plug must be accessible after installation.
Risk of damaging appliance!
• Your product is only for home use and is only designed
for the textiles suitable for machine washing.
• Do not climb up and sit on top cover of the machine.
• Do not lean against machine door.
• Cautions during Handling Machine:
1.Transport bolts shall be reinstalled to the machine by
a specialized person.
2.The accumulated water shall be drained out of the
machine.
3.Handle the machine carefully. Never hold each protruded
part on the machine while lifting. Machine door can
not be used as the handle during the conveyance.
4.This appliance is heavy. Transport with care.
6
SAFETY INSTRUCTIONS
• Please do not close the door with excessive forces.
• It is forbidden to wash carpets.
Operating the appliance!
• Before washing the clothes at first time, the product
shall be operated in one round of the whole procedures
without the clothes inside.
• Flammable and explosive or toxic solvents are forbidden.
Gasoline and alcohol etc.Shall not be used as detergents.
Please only select the detergents suitable for machine
washing, especially for drum.
• Make sure that all pockets are emptied. Sharp and rigid
items such as coin, brooch, nail, screw or stone etc. may
cause serious damages to this machine.
• Please check whether the water inside the drum has
been drained before opening its door.Please do not open
the door if there is any water visible.
• Be careful of burning when the product drains hot
washing water.
• Never refill the water by hand during washing.
• After the program is completed, Please wait for two
minutes to open the door.
Packaging/Old appliance
This marking indicates that this product should not be disposed
with other household wastes throughout the EU.To prevent
possible harm to the environment or human health from
uncontrolled waste disposal,recycle it responsibly to promote
the sustainable reuse of material resources.To return your used
device,please use the collection systems or contact the retailer
where the product was purchased. They return and can take this
product for environmental safe recycling.
7
INSTALLATION
Product Description
Top lid
Frame
Control panel
Cabinet
Adjustable foot knob
Drain hose
Water inlet valve
Power case and plug
Note!
• The product line chart is for reference only, please refer to real product as
standard.
Handle
Or
Accessories
cabinet baseboard
screw
Note!
• Note: if the drain hose is already installed on the machine, then there is no
spring clamper and drain hose in the accessories.
8
spring clamper drain loose ass Inlet hose ass manual
Or
INSTALLATION
Installation area
Warning!
•
Stability is important to prevent the product from
wandering!
•
Make sure that the product should not stand on
the power cord.
Before installing the machine, the location characterized
as
follows shall be selected:
1.Rigid, dry, and level surface
2.Avoid direct sunlight
3.Sufficient ventilation
4.Room temperature is above 0 C
5.Keep far away from the heat resources such as coal or gas.
Unpacking the washing machine
Warning!
• • Packaging material (e.g. Films, Styrofoam) can be
dangerous for children.
There is a risk of suffocation ! Keep all packaging
well away from children.
w
W> 20mm
w
1. Remove the cardboard box and styrofoam packing.
2. Lift the washing machine and remove the base packing.
3. Remove the tape securing the power supply cord and
drain hose.
4. Remove the inlet hose from the drum.
Installation of drain hose
1.Completely sleeve the drain hose over the sewer.
2.Fix and tighten it with a hoop.( As shown in the figure )
Note!
• Note: The drain hose of the machine with upper drain system has already been
assembled before leaving the factory. This picture is suitable for lower drain system.
9
INSTALLATION
Warning!Warning!
Do not kink or protract the drain hose.
•
• Position drain hose properly ,otherwise damage might result of water leakage.
• If drain hose is too long, do not force it into washing machine as it will cause
abnormal noises.
There are two ways to place the end of drain hose:
1.For lower drain system
Under3m
Under 15cm
2.For upper drain system
Trough
Hose
Retainer
d
n
i
B
Max.1 00cm
Min.86cm
wate r trough
m
6c
n.8
Mi
m
0c
0
1
.
x
Ma
Levelling the washing machine
Warning!
• The lock nuts on all four feet must be screwed tightly against the housing.
1.Check if the legs are closely attached
the cabinet. If not, please turn them to
their original positions tighten the nuts.
2.Check alignment of the product with a
spirit level and if required, correct.
3.Loosen the lock nut and turn the feet
until it closely contacts with
the floor.
4.After being locked properly, press four
corners again to make sure that they has
been adjusted properly.
to
10
Lock nut
Raise
foot
lockloosen
Lower
right
wrong
INSTALLATION
Selection of Tap
Please select
tap.
appropriate
Ordinary faucet
Screw tap
Special wa shing
machine tap
Connection of inlet hose, tap and washing machine
1:Connection between ordinary tap and inlet hose.
Wall
tap
clamp nut
1.Loosen clamp nut to
show 5mm thread
slide b ush ing
5.Press slide bushing,
insert inlet hose into
connecting base
2:connection between screw tap and inlet hose.
2.Loosen four bolts 3.Set connecting base
on tap and t ighten
bolts evenly
inlet hose
6.connection finished 7.After connection and installation,
check if there is water leakage
4.Tighten clamp nut
inlet valve
slide b ush ing
tap with threads and inlet hose
special tap for washing machine
Warning!
• To prevent leakage or water damage, follow the instructions in this chapter
Do not kink, crush, modify or sever .
• water inlet hose
11
!
OPERATIONS
Preparation Before Washing
Caution!
•
Before washing, please make sure it’s installed properly.
•
Before washing it at first time, the washing machine shall be operated in one
round
of the whole procedures without clothes in as follows.
1 2 3 4
Plug in
Open tap
load and Close door
Add detergent
Washing
1 2
Power On
Select Programme Select Level
Note!
• , If default is selected, step 2 3 can be skipped.
3 4
Start up
After Washing
Buzzer will beep after washing finished and the power supply will be cut off automatically
Then unload the laundry.
.
12
OPERATIONS
• The working condition of the washer should be(0-40)℃.If used under 0℃,the inlet
valve and draining system may be damaged. If the machine is placed under condition
of 0℃or less, then it should be transferred to normal ambient temperature to ensure
the water supply hose and drain hose are not frozen before use.
• Please check the labels and the explanation of using detergent before wash. Use
non-foaming or less-foaming detergent suitable for machine washing properly.
Washing matters needing attention
Check the label
Put small clothes into the
pillow slip
！
alarm due to great unbalance. Therefore it is suggested to add one or two
more clothes to be washed together so that draining can be done smoothly.
• Don’t washing the clothes touching with kerosene, gasoline, alcohol and
other flammable materials.
• As for the agglomerated or ropy detergent or additive, before they are
poured the detergent box, it is suggested to use some water for
dilution to prevent inlet of detergent box from being blocked and
overflowing while filling water.
•
temperature to get the best washing performance with less water and
energy consumption.
Warning!
• When washing a single clothes, it may easily cause great eccentricity and give
The uasage of detergent and Washing powder
into
Please choose suitable type of detergent for the various washing
Take out the items out of
the pockets
Turn easy-pilling and
long-pile fabric inside out
the
Knot the long strips,zip or
button
Separate clothes with
different textures
13
OPERATIONS
Control Panel
XXX
XXX
XXX
XXX
XXX
XXX
XXX
XXX
8
7
5
6
3
4
1
2
Soak
Was h
Rinse
Spin
(Pow er)
Wat er Leve l
5
6
4
Control Panel
XXX
XXX
XXX
XXX
XXX
XXX
XXX
XXX
Program
Child Lock
6
Note!
The chart is for reference only, Please refer to real product as standard.•
1
On/Off
1
Product is switched on or off.
3
Process
After power on, one light will flash among
the function of soak wash rinse and spin
according to real process.
5
Child Lock
Press Program+Water level at same time,
only power switch button is available.
Press again, Program+Water level Child Lock
will be canceled.
7
5
3
1
Water level
5
, , ,
4
Funct io n
8
6
4
2
3
Soak
Wash
Rinse
Spin
Process
3 12
2
Start/Pause
1
Press the button to start or pause the
washing cycle.
4
Water level
Eight water levels are set for this washer
from at the lowest level to at the highest
level.
6
Programmes
Available according to the laundry type.
12
14
OPERATIONS
Option
Water Level
select water level according to clothing categories, degree of soiling and washing
habits of customers
Function
washing time, rinsing times, spinning time and other settings can
be selectable
Child Lock
To avoid mis operation by children.
Power on
Start
Press Child Lock
Caution!
• Press the two button 3sec. also to be released the function.
• The “Child Lock” will lock all buttons except [ On/Off ].
•
Cut off the power supply , the kid’s protection is to be released .
15
OPERATIONS
personalized setting of washing program
Customers can select washing program according to actual demand, and set washing
rinsing 、spinning function 、water volume function、 function
On Start
(Power)
Program
Water Level
Function
(Process)
operations of washing process
customers can set single process or combinations of washing、rinsing and spinning
freely according to demand. Detailed operations as follows for different models:
One Touch Smart Wash
On
(Power)
Wash
On
(Power)
Spin
On
(Power)
Wash Spin+Rinse+
Start
keep pressing Function key
until wash light is on only
keep pressing Function key until
spinning light is on only
Start
Start
On
Note: other process combinations are just like above.
keep pressing Function key until
washing、
rinsing
、
spinning lights are on
10
16
Start
OPERATIONS
Washing Programmes Table
Programmes are available according to the laundry type.
XXXXXX
Only for washers having these function
XXXXXX
Programmes
XXXXXX
XXXXXX
Jeans:
Suitable to wash heavy stained/wearable clothes.
Quick:
(Quick 15")
Tub clean
Delicate:
Suitable to wash light stained clothes and clothes in summer.
Clean the tub. This program can prevent from crossing infection,
including wash, rinse and spin a whole process.
Mid/High/Low water level selection, the tempo is soft, slow washing
and spinning speed, to make the lightest wear and deformation.
As for not easily fading, deforming , and non-waterproof clothes ,
Air dry
Standard
(Normal)
can use the function
the result of being dried in a room.
Standard fabric washing program, suitable to wash ramie cotton fabric.
Wash for once, rinsing for twice, the spin time is a little long.
to dry clothes without heating, and to reach
Bulky Washing ability is strong ,washing more the dirty clothes.
Mini wash
ECO
Washing a few clothings , low water level ,high water level shall not
choice.
1 time rising is suitable for light contaminated clothes in order to
save water.
The washing machine will select the water level automatically
according to the load weight.
Fuzzy
weighting:
1. When there's water in the tub, this function is not available;
2. Before press [Start/Pause] button, if consumer selected the
water level, there will be no fuzzy weighting function;
3. After press [Start/Pause] button, the washing machine will run
the fuzzy weighting function. Consumer can also select the water
level to set the water level as needed.
17
10
MAINTENANCES
Cleaning And Care
Warning!
• Before your maintenance starts, please unplug the machine and close the tap.
Cleaning the cabinet
Proper maintenance on the washing machine can extend its
working life. The surface can be cleaned with diluted
non-abrasive neutral detergents when necessary. If there is
any water overflow, use the wet cloth to wipe it off immediately.
No sharp items are allowed.
Note!
Formic acid and its diluted solvents or equivalent are forbidden, such as
•
solvents or chemical products,etc.
alcohol,
Cleaning the inlet filter
Note!
• Inlet filter must be cleaned if there is less water.
Washing the filter in washing machine:
1.Screw off the inlet pipe from the backside
of the machine.
2.Pull out the filter with long nose pliers
and reinstall it back after being washed.
3.Use to clean the filter.
the brush
4.Reconnect the inlet pipe.
Lint filter clean
1.There is a built-in lint filter in your washer. It
can help to collect lint during washing cycle.
2.It is suggested to clean the lint filter every
10 cycles.
3.Take it out and clean the filter with water.
Then place it back into the washer.
18
magic filter
normal filter
10
MAINTENANCES
Cleaning drain pump filter
Warning!
Be careful of the hot water!
•
Allow detergent solution to cool down.
•
• Unplug the machine to avoid electrical shock before washing.
• Drain pump filter can filter the yarns and small foreign matters from the
washing.
• Clean the filter periodically to ensure the normal operation of washing
machine.
Drain the water out of the
pump, under which use a
container to collect.
Clean the filter.
1
Open the filter by turning
to the counter clockwise
4
Restore it and adjust the convex
place to align at the pump hole.
2
Remove extraneous matter
5
Tighten the pump
cover clockwise.
Caution!
• Make sure that valve cap and emergency drain hose are reinstalled properly, cap
plates should be inserted aligning to hole plates otherwise water may leak;
• Some machines don’t have emergency drain hose, so step 2 and step 3 can be skipped.
Rotate lower cover cap directly to make water run into basin.
• When the appliance is in use and depending on the programme selected there can
be hot water in the pump. Never remove the pump cover during a wash cycle, always
wait until the appliance has finished the cycle, and is empty. When replacing the
cover, ensure it is securely re-tightened.
3
6
19
10
MAINTENANCES
Trouble Shooting
The start of the appliance does not work or it stops during operation.
First try to find a solution to the problem, If not, contact the service centre.
Description
No washing
No water flows in
Abnormal draining
Abnormal spin
Description
flare
flare
flare
flare
Inspection Items
If the power is off or the fuse is burned out.
If the power supply voltage is too low.
If the water amount reaches to the required water level.(The washer will
not work if the water amount does not reach the required water level)
If it is set to "Delay" washing mode. (It will only start to work until the
reservation time reached)
If the power is off or the fuse is burned out.
If the water supply is cut off or the water pressure is too low.
If the inlet hose is properly connected and the water tap is opened.
If the filtering screen of inlet valve is blocked by dirt.
If the coil of inlet valve is damaged. (The slight electromagnetic sound is
normal phenomenon when the inlet valve is switched on)
If the "Start / Pause" button is pressed after the power switch is pressed.
If the water drain hose is placed very high.
If the end of water drain hose is sealed in pond.
If the internal rubber ring of drain valve is blocked by dirt.
If the door lid is closed.
If all clothing piled largely at one side of barrel or the clothing is excessively
placed.
If the washer is not placed in stable condition or it is placed in inclination
state. (The ground is not flat).
If the motor belt is loosened.
Reason
Alarm for abnormal
water intaking.
Alarm for lid not closed
before wash and spin.
Alarm for washing stay
at one side.
Alarm for water drain
has not finished.
Check the water tap is
opened or not.
Closed the lid.
Manually balance clothes
in the barrel by hands.
Check the water level
sensor and drain pump.
Solution
Note!
• or the display
After the check, activate the appliance. If the problem occurs
shows other alarm codes
again, contact the service.
10
20
MAINTENANCES
Technical Specifications
Model
MFW-752S
MFW-EC750
MFW-852S
MFW-952S
MFW-EC950
Washing
Capacity
7.0kg
8.0kg
9.0kg
Dimension
(W*D*Hmm)
515x525x915
550x565x920
550x565x955
Net
Weight
29kg
34kg
37kg
Rated
Power
400W
450W
480W
Power Supply
220-230V~,50Hz
220-240V~,50Hz
220-240V~,50Hz
Standard Water
Pressure
0.03MPa~0.8MPa
0.03MPa~0.8MPa
0.03MPa~0.8MPa
102410
21
Loading...