How it Works
Midea
Loading...
MCH-90TM1
User Manual
37 pgs9.66 Mb0

Midea MCH-90TM1 User Manual

Download
Hud Dapur
Manual Pengguna
Cooker Hood
User Manual
烟机
用户手册
Contents
EN-1
Contents
01 02
03 04
05 06 07
08 09
Contents.................................................................
Warnings................................................................2
Safety Warning.......................................................3
Notice of Installation...............................................4
Use...................................................................
Maintenance......................................................... 10
Trouble Shooting.................................................. 11
Main Parameters..................................................
Disposal................................................................
12
12
1
7
Warnings
EN-2
This appliance can be used by children aged from 8
z
years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. There shall be adequate ventilation of the room when
z
the range hood is used at the same time as appliances burning gas or other fuels.
The filter is made of high density aluminum.
z z
Please do not use corrosive detergent for cleaning. The proper function of the unit is conditioned by the regularity of the maintenance. To protect the main body from corrosive of the long time
z
accumulation of dirt, the cooker hood should be cleaned with hot water with non-corrosive detergent every two months.
There is a fire risk if cleaning is not carried out in
z
accordance with the instructions.
Do not flame under the range hood.
z z
The air must not be discharged into a flue that is used
for exhausting fumes from appliances burning gas or other fuels. The minimum distance between the supporting surface
z
for the cooking vessels on the hob and the lowest part of the range hood is 650 mm. Regulations concerning the discharge of air have to be
z
fulfilled. The appliance uses 4 hob elements at most.
z z
CAUTION : used with cooking appliances.
Accessible parts may become hot when
Safety Warning
EN-3
The appliance is not intended for use by young children or infirm
persons without supervisions.
Young children should be supervised to ensure they do not play with
the appliance.
Plug the power cord to socket outlet with earthing continuity terminal.
The cooker hood is for home use only, not suitable for barbecue, roast
shop and other commercial purposes.
The cooker hood and its filter should be cleaned regularly
according to the instruction.
Do not use open flame, or allow oil to go beneath the appliance.
If there is any fault occurred with the appliance, please call after-sale
service department.
Please keep the kitchen room ventilated.
Prior to any maintenance, cleaning operation, ensure the power is cut
off.
If the supply cord is damaged, it must be replaced by the manufacturer,
service agent or similarly qualified person in order to avoid a hazard.
The replaced power cord should be provided by manufacturer or seller.
If the plug or cord is damaged, please call after-sale service center.
There is a fire risk if cleaning is not carried out in accordance with the
instruction.
In case of damaged connecting wire, please refer to the manufacturer,
after-sale service personnel or other qualified technicians.
Use the unit according to the instructions to avoid any fire hazard.
The exhaust air must not be introduced into a smoke flue or chimney
that is used for exhausting fumes from appliances burning gas.
Follow the local laws applicable for external air evacuation.
Notice of Installation
EN-4
It can not share the same air ventilation tube with other appliance
such as gas tube, warmer tube, and hot wind tube. There will be
hazard of underpressure, combustion impaired and harmful gases
drawn back.
The bending of ventilation tube should be ≥120°,parallel or above the
start point/should be connected to the external wall.
placed horizontally to avoid
Please make sure the installation plate is
grease collection at one end. See Fig.1.
Right Wrong
After installation, make sure that plug can be pulled out if necessary.
ed 650~750 mm up from the
T he cooker hood should be plac
cooking plane for safe and a good effect. See Fig.2.
Fig.1
There shall be adequate ventilation of the room when the cooker
hood is working.
Option Chimney X
EN-5
√
X
1 x Installation plate
2 x Chimney installation plates
Fig.2
5 x Plastic expansion pipes
5 x Screws(ST5*50)
Fig.3
2
x Screws(M5*12)
4 x Screws(ST4.2*9.5)
Installation
EN-6
Accessories. See Fig.3. (Type and quantity of accessories is
subject to actual demand.)
Fix installation plate and extension chim
ney installation plate, install
the plastic expansion pipes of chimney installation plate on wall.
See Fig.4.
Hang range hood on the installation plate. See Fig.5.
Fix the exhaust pipe on the main body, lock screws (M5*12) to
prevent the range hood from accidently sliding off the installation plate.
See Fig.6.
Connect chimney installation plate and chimney. See Fig.7.
Fix chimney installation plate. See Fig.8.
Fix the extension chimney. See Fig.9.
Fig.4 Fig.5
Fig.6
EN-7
Fig.7
Fig.9
Stop Low Mid High Light
Fig.8
Speed adjustment. See Fig.10.1.
Stop
Press
Press the
Press the
Press the
Press the
button, the motor will stop running.
Low
(speed) button, the motor runs at low speed.
Mid
(speed) button, th
High
(speed) button,
Light
button, the two lighting lamps will come on.
(For some models)
e motor runs at mid speed.
the motor runs at high speed.
Fig.10.1
Press it again and the lamps will be turned off.
7 X Screws(M5*50)
Use
Speed adjustment. See Fig.10.2.
EN-8
are the hood is connected with
After plugging, buzz once to decl
(For some models)
electricity. After the connection:
Pr
ess the l motor power: under standby state,
Power button, contro
press this button, motor will run at low speed, and light for power
and low speed button will be on; under power-on state, press this button,
hood will enter 3-min-delay-shutdown st
ate, press power button again
under this state, the hood will turn off( motor stops running).
Press the Light button, control
light being on and off independently
without any other buttons’ help. Press it once, lights will be on.
Press again, they will be off.
High b utton, valid under p ower-on state. While running at
Pr ess
the
middle or low speed mode, press this button, the hood will enter high
speed mode. If already running at high speed, pressing this button takes
no effect. In 3-min-delay-shutdown state, press it, the hood cancels
delay shutdown mode and enter high speed running state.
Press the Low button, valid under power-on state. While running at
high or middle speed mode, press this button, the hood will enter low
speed mode. If already running at low speed, pressing this button takes
no effect. In 3-min-delay-shutdown state, press it, the hood cancels
delay shutdown mode and enter low speed running state.
Light Low Mid High Power
Fig.10.2
222
Speed adjustment. See Fig.10.3. (For some mod s)
EN-9
el
After the hood is switched on, a beep sound heard and all key lights are
lightened for 1 s, indicating the hood has been powered on. Under the
condition of hood power-on:
Power Key: control the motor power, under standby state, press the
“power” button, “power” key light is
o
n, the motor starts up at low
speed, digital screen displays setting 1; under power-on state, press
the “power” button, enter 3-min-delay-shutdown state, setting
switched to low speed, the power key flashes at one second interval,
which means entering delay-shutdown state; under delay-shutdown
state, press the “power” button, it’s shut down immediately (motor
stops running).
Light Key: independently control the light on and off free from the
effect of other keys. Press it once, the light is on, meanwhile the
light key light is on; press again, he light is off and light key
t
light is off too.
Plus (+) Key: valid under power-on state, press plus (+) key once,
motor speed increased one setting, digital tube displays corresponding
setting. When the plus (+) key is pressed down, plus (+) key light is on.
When at the highest setting, only give out key touch sound, the setting
no longer changes.
Minus (-) Key: alid under power-on state, press “minus (-)” key once,
v
motor speed decreased one setting, digital tube displays
corresponding setting. When the “minus (-)”key is pressed down,
“minus (-)”key light is on. When at the lowest setting, only give out key
touch sound, the setting no longer changes.
Light Minus Digital screen Plus Power
Fig.10.3
Maintenance
EN-10
Contents
Cleaning of the filters
Removing the filters according to Fig.1 . Put into a dishwasher with detergent, set the temperature below
60 degrees.
Please do not use abrasive detergent for it will damage the hood. Make sure that the hood is shut off before cleaning.
1
Fig.11 Fig.12
Replacement of the carbon filters ( )
Remove the filters see Fig.11. The carbon filters are located at both end of the motor.
Turn the carbon filters until they are locked. S ee Fig.12.
Apply reverse procedure to It should be replaced after approximately 2-3 months of use. The carbon filer cannot be washed or recycled. Carbon filter is not supplied with your appliance.
remove the carbon filter.
Option
al
222
Trouble Shooting
EN-11
Fault
Light on, but motor does not work.
Both light and motor
do not work.
Oil leakage.
Vibration.
Insufficient suction.
The machine inclines.
Cause Solution
The blades are blocked. The capacitor is damaged. Replace capacitor. The motor is damaged. Replace motor. The internal wiring of motor is cut off / disconnected. An unpleaseant smell may be produced. Apart from the above mentioned, check the following: Light damaged. Replace lights.
Power cord loose.
Outlet and the air ventilation entrance are not tightly sealed. Leakage from the connection of U-shaped section and cover. The blade, if damaged, can cause vibrating. The motor is not tightly fastened. Fasten the motor tightly. The cooker hood is not tightly fixed. Fixed the cooker hood tightly. The distance between the cooker hood and the cooker top is too large.
Too much ventilation from open doors or windows.
The fixing screws are not tight enough. The hanging screws are not tight enough
.
Replace motor.
Connect the wires as per the electric diagram. Take down the outlet and seal with glue. Take U-shaped section down and seal with soap or paint.
Replace the blade.
Readjust the distance.
Choose a new place to install the appliance or close some doors / windows. Tighten the fixing screw and make it horizontal. Tighten the hanging screw and make it horizontal.
Electrical Diagram
Electrical diagram see label on main body of the actual product.
222
Main Parameters
EN-12
egatloV
Rated Power
Lighting Power
Motor Power
Diameter of air tube
esioN
The air flow parameter is tested under conditions of 230V 50Hz when the
voltage is 220-240V
~
50/60Hz and without carbon filters.
220-240V~50/60Hz
333W
2 X 1.5W
330W
150mm
≤
74dB
~
Disposal
Please dispose of it at your local community waste collection /
recycling center and ensure it presents no danger to children
while being stored for disposal. The plug must be rendered
useless and the cable cut off to prevent misuse.
222
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use