Midea MAW08V1QWT, MAW10V1QWT, MAW12V1QWT Installation Manual

Page 1 Installation GuideInstallation Guide Page 3

Page 2

Models MAW08V1QWT

MAW10V1QWT MAW12V1QWT

Window Type Air Conditioner

You must follow the user manual for detailed installation instructions

Before using your air conditioner, please read the user manual carefully and keep for future reference. For additional support, please call customer service at 1-866-646-4332.

version A - 03 - 2020

Installation Guide

Scan the following QR code for an installation video.

TOOL & HARDWARE

WINDOW REQUIREMENTS

Required Installation Hardware Optional Installation Hardware

Side Arm Foam 2

Right Extension Arm – Short (For 22”-26” windows)

Cotter Pin

Open Window Bracket – LH 1

Open Window Bracket – RH

Main Support Pin

Right Extension Arm (For 26”-36” windows)

1Main Bracket

1/2” Type A Screw 3

1/2” Type B Screw 2

1/4” Type B Screw 2

Window Sash Lock

Thick Window Sash Seal Foam

Thin Window Sash Seal Foam

Miscellaneous Sealing Foam

Additional Side Arm Foam

1” Type A Screw 2

Wooden Windows

INNER WINDOW SILL

INTERIOR WALL

13.75" min (349 mm)

22" to 36"

(558 mm to 914mm)

SEAL FOAM

Vinyl-Clad Windows

INNER WINDOW SILL

13.75" min (349 mm)

22" to 36"

(558 mm to 914mm)

SEAL FOAM

Wooden Windows

INSIDE

OUTSIDE

INSIDE

OUTSIDE

Vinyl-Clad Windows

Vinyl Lip

1. INSTALL THE SUPPORT BRACKET

1.1 Adjust the left extension arm out and install the right extension arm. Set the bracket in your window.

1.2 Adjust the angled support arms until they touch the exterior wall. Check that the bracket is properly tilted downwards toward the outdoors. Install the support pins and cotter pins then extend the left and right extension arms.

Center this part of the

bracket with the center

of the windows.

Extend the Extension Arms until they touch the

Windowsill and the Spring Pin locks in place.

Depending on the

level used, place at

either location below

to check level.

WARNING

Do not use any devices or materials for installation that are not recommended in this manual.

NOTICE

Maximum window thickness including non-removable handle: 2-7/8”

Cotter Pin

Spring

Locks

Spring Pin Locks

WARNING

• Bracket should only be used for its intended purpose. If not, the warranty will be voided.

• You must follow the detailed installation instructions in the user manual.

WARNING

Maintain control of the bracket until installation is complete.

Right Extension Arm

Horizontal Bracket

Left Extension Arm

Page 4 Installation GuideInstallation Guide Page 6Page 5

2.2 You must install the Open Window Brackets.

Use the 1/2”

Type B screw

Use the 1/4”

Type B

screw

2. SECURE THE UNIT ON THE BRACKET

2.1 Set the air conditioner on the support bracket and fold down the side arm hinges.

3. SEAL AND CLOSE THE WINDOW

3.3 Use the included foam to seal any gaps between the window and the air conditioner.

Use the window sash seal foam to seal between the windows

Check fo

Check

for

Gaps

Use the thick window sash seal foam to seal between

the windows

3.4 Extend both window locks located in the window slot. For additional security, install the window sash lock.

FAQ Why is there noise during cooling?

- It is normal to hear airflow, set to a slower fan setting if too loud.

- Window vibration - poor installation. Refer to installation instructions or check with installer.

FAQ Unit will not connect to Wifi or App does not work?

For additional support and troubleshooting tips, follow the link in this QR code.

- Wall plug disconnected. Push plug firmly into wall outlet.

- House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker.

- Check if the light on the plug is on. If it is off, press the RESET button.

- Power is OFF. Turn power ON.

FAQ Why does the air conditioner not start?

Top view

Extend into Window Track

Remove the factory installed 1/2”

screw and extend the Anti-Tip

Brackets into the window track.

Secure the Anti-Tip Brackets by

re-using the factory installed 1/2”

screw. Failing to use this screw

could damage the air conditioner.

Top of Unit

Use the provided 1/2” Type A screws.

NOTE: Drill 1/8” pilot holes before

screwing into the window sill.

1. INSTALL THE SUPPORT BRACKET (cont.)

1.3 Secure the bracket to the window with a screw at the end of each extension arm as shown. Holes at the end or bottom of the Extension Arms can be used to secure the Support Bracket to the window.

3.1 Measure, cut and install the side arm foam.

3.2 Secure the anti-tip brackets into the window track and then close the window.

WARNING

Do not leave the unit unattended during installation.

WARNING

Failing to do this could cause injury or property damage.

WARNING

Do not leave the unit unattended during installation.

WARNING

You must extend the Anti-Tip Brackets into the Window Track Opening. Failure to follow this warning may cause serious injury.