Midea MLH52N4AWW User Manual
Washer
Power supply: 120V
Circuit: 16-amp branch
en
USER MANUAL &
INSTALLATION
INSTRUCTIONS
Warning:
Before using this product,
please read this manual carefully
and keep it for future reference.
The design and specifications
are subject to change without
prior notice for product
improvement. Consult with your
dealer or manufacturer for
details.
MODEL NUMBER
MLH52N4AWW
www.midea.com/ca
Dear user
THANK YOU and CONGRATULATIONS on your purchase of
this high-quality Midea product. Your Midea washer is designed
for reliable, trouble-free performance. Please take a moment to
register your new washer.
Register your new washer at
https://www.midea.com/ca/support/Product-registration
For future reference, record your product model and serial
numbers located on the inside frame of the washer.
Model Number________________________________________
Serial Number_________________________________________
WASHER SAFETY ..............................................................................3
Proper Installation ....................................................................................5
When Not in Use .......................................................................................5
OPERATION REQUIREMENTS .........................................................6
Location of Your Washer .......................................................................6
Electrical Requirements .........................................................................6
Water Supply Requirements ................................................................7
Drain Requirements .................................................................................7
INSTALLATION INSTRUCTIONS ......................................................8
Before You Begin ......................................................................................8
Tools Required ...........................................................................................8
Parts Required (Obtain Locally) .........................................................9
Parts Supplied............................................................................................9
Rough-In Dimensions ..............................................................................9
Unpacking the Washer .........................................................................10
Installing the Washer ..............................................................................11
WASHER USE ...................................................................................13
Control Panel ............................................................................................13
Features .....................................................................................................20
Loading and Using the Washer ........................................................23
WASHER CARE ................................................................................24
Cleaning ....................................................................................................24
Moving, Storage and Long Vacations ............................................28
BEFORE YOU CALL FOR SERVICE... ............................................29
Error Codes ..............................................................................................36
WARRANTY .....................................................................................37
PRODUCT REGISTRATION .............................................................39
WASHER SAFETY
YOUR SAFETY AND THE SAFETY OF OTHERS ARE VERY
IMPORTANT
To prevent injury to the user or other people and property damage, the
instructions shown here must be followed. Incorrect operation due to
ignoring of instructions may cause harm or damage, including death.
The level of risk is shown by the following indications.
This symbol indicates the possibility of death or serious
WARNINGWARNING
CAUTION
WARNING
injury.
This symbol indicates the possibility of injury or damage to
property.
This symbol indicates the possibility of dangerous voltage
constituting a risk of electrical shock is present that could
result in death or serious injury.
Washer
Safety
Requirements
Operation
Instructions
Installation
Washer Use Washer Care
Troubleshooting
3
Washer
Safety
Requirements
Operation
Instructions
Installation
Washer Use
Washer Care
Troubleshooting
IMPORTANT SAFETY INSTRUCTIONS
WARNING
To reduce the risk of death, fire, explosion, electric shock, or injury
to persons when using your vfd appliance, follow basic precautions,
including the following:
Read the instruction manual before using the appliance.
•
DO NOT wash or dry articles that have been previously cleaned in,
•
washed in, soaked in or spotted with gasoline, dry-cleaning solvents,
or other flammable or explosive substances, as they give off vapors
that could ignite or explode.
DO NOT add gasoline, dry-cleaning solvents, or other flammable or
•
explosive substances to the wash water. These substances give off
vapors that could ignite or explode.
Under certain conditions, hydrogen gas may be produced in a
•
hot-water system that has not been used for 2 weeks or more.
HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not
been used for such a period, before using a washing machine, turn
on all hot-water faucets and let the water flow from each for several
minutes. This will release any accumulated hydrogen gas. As the gas
is flammable, DO NOT smoke or use an open flame during this time.
DO NOT allow children to play on or in this appliance. Close
•
supervision of children is necessary when this appliance is used near
children. Before the washer is removed from service or discarded,
remove the door or lid. Failure to follow these instructions may result
in death or injury to persons.
DO NOT reach into the appliance if the drum or other components
•
are moving to prevent accidental entanglement.
DO NOT install or store this appliance where it will be exposed to the
•
weather.
DO NOT tamper with controls, repair or replace any part of this
•
appliance or attempt any servicing unless specifically recommended
in the user maintenance instructions or in published user repair
instructions that you understand and have the skills to carry out.
Keep the area around your appliance clean and dry to reduce the
•
possibility of slipping.
DO NOT operate this appliance if it is damaged, malfunctioning,
•
partially disassembled, or has missing or broken parts including a
damaged cord or plug.
Unplug the appliance or turn off the circuit breaker before servicing.
•
Pressing the Power button DOES NOT disconnect power.
See “Electrical Requirements” located in the Installation Instructions
•
for grounding instructions. This appliance is not intended for use
by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with appliance.
4
If the supply cord is damaged, it must be replaced by the
•
manufacture, its service agent or similarly qualified persons in order
to avoid a hazard.
The new hose-sets bought from the retailer where the product was
•
purchased are to be used and that old hose-sets should not be
reused.
This appliance is for indoor use only.
•
SAVE THESE INSTUCTIONS
PROPER INSTALLATION
This washer must be properly installed and located in accordance
•
with the Installation Instructions before it is used. Ensure the cold
water hose is connected to the “C” valve.
Install or store where it will not be exposed to temperatures below
•
freezing or exposed to the weather, which could cause permanent
damage and invalidate the warranty.
Properly ground washer to conform with all governing codes and
ordinances. Follow details in installation instructions.
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
•
Do not remove the ground prong.
•
Do not use an adapter.
•
Do not use an extension cord.
•
Failure to do so can result in death, fire or electrical
•
shock.
Washer
Safety
Requirements
Operation
Instructions
Installation
Washer Use Washer Care
WHEN NOT IN USE
Turn off water faucets to minimize leakage if a break or rupture should
occur. Check the condition of the fill hoses; We recommend changing the
hoses every 5 years.
State of California Proposition 65 Warnings:
WARNING: Cancer and Reproductive Harm
-www.P65Warnings.ca.gov.
SAVE THESE INSTRUCTIONS
THIS APPLIANCE IS FOR HOUSEHOLD USE ONLY
Troubleshooting
5
Washer
Safety
Requirements
Operation
Instructions
Installation
Washer Use Washer Care
OPERATION REQUIREMENTS
LOCATION OF YOUR WASHER
DO NOT INSTALL THE WASHER:
1.
In an area exposed to dripping water or outside weather conditions.
The ambient temperature should never be below 60°F (15.6 ) for ℃
proper washer operation.
2. In an area where it will come in contact with curtains or drapes.
3. On carpet. The floor MUST be a hard surface with a maximum slope
NOTE: If floor is in poor condition, use
solidly attached to the existing floor covering.
IMPORTANT: MINIMUM INSTALLATION CLEARANCES
• When installed in alcove: Top and Sides = 0" (0 cm), Back = 3" (7.6 cm)
• When installed in closet: Top and Sides = 0" (0 cm), Front = 2" (5 cm),
Back = 3" (7.6 cm)
• Closet door ventilation openings required: 2 louvers each 60 square in.
(387 cm), located 3" (7.6 cm) from top and bottom of door
ELECTRICAL REQUIREMENTS
Read these instructions completely and carefully.
" per foot (1.27 cm per 30 cm). To make sure the washer does not
of
1/2
vibrate or move, you may have to reinforce the floor.
" impregnated plywood sheet
3/4
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK AND PERSONAL
INJURY:
Troubleshooting
6
•
CIRCUIT - Individual, properly polarized and grounded 16-amp branch
circuit fused with 16-amp time -delay fuse or circuit breaker.
POWER SUPPLY - 2-wire with ground, 120V, single-phase, 60Hz,
alternating current.
OUTLET RECEPTACLE - Properly grounded receptacle located so the
power supply cord is accessible when the washer is in an installed
position.
WARNING
DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG
WITH THIS APPLIANCE. Washer must be electrically grounded in
accordance with local codes and ordinances.
GROUNDING REQUIREMENTS
Improper connection of the equipment grounding conductor can result
in a risk of electrical shock. Check with a licensed electrician if you are in
doubt as to whether the appliance is properly grounded.
1. The washer MUST be grounded. In the event of malfunction or
breakdown, grounding will reduce the risk of electrical shock by
providing a path of least resistance for electrical current.
2. Since your washer is equipped with a power supply cord having an
equipment-grounding conductor and a grounding plug, the plug
MUST be plugged into an appropriate, copper-wired receptacle that
is properly installed and grounded in accordance with all local codes.
If in doubt, call a licensed electrician. DO NOT cut off or alter the
grounding prong on the power supply cord. In situations where a twoslot receptacle is present, it is the owner’s responsibility to have a
licensed electrician replace it with a properly grounded grounding-type
receptacle.
WATER SUPPLY REQUIREMENTS
Hot and cold water faucet MUST be installed within 42" (107 cm) of your
washer’s water inlet. The faucet MUST be
" (1.9 cm) garden hose-type so
3/4
inlet hoses can be connected. Water pressure MUST be between 10 and 120
psi. Your water department can advise you of your water pressure.
DRAIN REQUIREMENTS
1. Drain capable of eliminating 64.3 L per minute.
1/4
2. A standpipe diameter of 1-
3. The standpipe height above the floor should be:
Minimum height: 24" (61 cm)
Maximum height: 47.24" (120 cm)
" (3.18 cm) minimum.
Washer
Safety
Requirements
Operation
Instructions
Installation
Washer Use Washer Care
Troubleshooting
BACK
(120 cm)
24''
(61 cm)
Min.
47.24''
Max.
7
Safety
INSTALLATION INSTRUCTIONS
BEFORE YOU BEGIN
Read these instructions completely and carefully.
Washer
IMPORTANT -
•
inspector’s use.
Save these instructions for local
Requirements
Operation
Instructions
Installation
Washer Use Washer Care
FOR YOUR SAFETY:
Troubleshooting
IMPORTANT -
•
ordinances.
• Note to Installer -
Consumer.
• Note to Consumer -
Skill level - Installation of this appliance requires basic mechanical
•
and electrical skills.
Completion time - 1-3 hours.
•
Proper installation is the responsibility of the installer.
•
Product failure due to improper installation is not covered under the
•
Warranty.
Observe all governing codes and
Be sure to leave these instructions with the
Keep these instructions for future reference.
WARNING
• This appliance must be properly grounded and installed as described
in these Installation Instructions.
• Do not install or store the appliance in an area where it will be exposed
to water/weather. See the Location of Your Washer section.
• NOTE: This appliance must be properly grounded, and electrical
service to the washer.
Certain internal parts are intentionally not grounded and may
•
present a risk of electric shock only during servicing. Service
Personnel - Do not contact the following parts while the appliance
is energized: Electrical Valve, Drai n Pu mp, Heater and Motor.
TOOLS REQUIRED
• A djustable wrench or
• Adjustable wrench or
• Channel-lock adjustable pliers
• Carpenter’s level
8
"(13mm) socket with ratchet
1/2
" (14mm) open-end wrench
9/16
PARTS REQUIRED (OBTAIN LOCALLY)
Water Hose (2)
PARTS SUPPLIED
Cable Tie
Drain Hose Guide
Washer
Safety
Requirements
Operation
Inlet Hose Screen Washers(2)
ROUGH-IN DIMENSIONS
27.0''
(68.6 cm)
39.8''
(101.09 cm)
∗NOTE: With pedestal, 52.6"
Stacked, 84"
SIDE
34.2''
(86.9cm)
39.8''
(101.09 cm)
Instructions
Installation
Washer Use Washer Care
Troubleshooting
9
Washer
Safety
Requirements
Operation
Instructions
Installation
Washer Use Washer Care
UNPACKING THE WASHER
WARNING:
Recycle or destroy the carton and plastic bags after the washer is
•
unpacked. Make materials inaccessible to children. Children might
use them for play. Cartons covered with rugs, bedspreads or plastic
sheets can become airtight chambers causing suffocation.
1. Cut and remove the top and bottom packaging straps.
2. While it is in the carton, carefully lay the washer on its side. DO NOT
lay the washer on its front of back.
3. Turn down the bottom flaps-remove all base packaging, including the
cardboard, styrofoam base and styrofoam tub support (inserted in
center of base).
NOTE: If you are installing a pedestal, proceed to the installation
instructions that come with the pedestal.
4. Carefully return the washer to an upright position and remove the
carton.
5. Carefully move the washer to within 4 feet (122 cm) of the final
location.
6. Remove the following from the back side of the washer:
4 bolts
4 plastic spacers (including rubber grommets)
4 power cord retainers
Troubleshooting
IMPORTANT: Failure to remove the shipping bolts* can cause the washer
to become severely unbalanced.
Save all bolts for future use.
* Any damages from failure to remove the shipping bolts are not covered by the
10
warranty.
NOTE: If you must transport the washer at a later date, you must reinstall
the shipping support hardware to prevent shipping damage. Keep the
hardware in the plastic bag provided.
INSTALLING THE WASHER
1. Run some water from the cold faucet to flush the water lines and
remove particles that might clog up the inlet hose.
2. Ensure there is a rubber washer in the hoses. Reinstall the rubber
washer into the hose fitting if it has fallen out during shipment.
Carefully connect the inlet hose marked HOT to the rear “H” inlet
of the water valve.Tighten by hand;then tighten another 2/3 turn
with pliers.And COLD to the rear “C” inlet of the water valve.
Tighten by hand;then tighten another 2/3 turn with pliers.
Do not crossthread or over-tighten these connections.
3. Install the screen washers by inserting them into the free ends of the
inlet hoses with protruded side facing the faucet.
4. Connect the inlet hose ends to the HOT and COLD water faucets
tightly by hand, then tighten another
turn with pliers. Turn the water
2/3
on and check for leaks.
Washer
Safety
Requirements
Operation
Instructions
Installation
Washer Use Washer Care
Troubleshooting
5. Carefully move the washer to its final location. Gently rock the washer
into position ensuring inlet hoses do not become kinked. It is important
not to damage the rubber leveling legs when moving your washer to
its final location. Damaged legs can increase washer vibration. It may
be helpful to spray window cleaner on the floor to help move your
washer into its final position.
NOTE: To reduce vibration, ensure that all four rubber leveling legs are
firmly touching the floor. Push and pull on the back right and then back
left of your washer.
11
Washer
Safety
Requirements
Operation
Instructions
Installation
Washer Use Washer Care
NOTE: Do not use the dispenser drawer or door to lift the washer.
NOTE: If you are installing into a drain pan, you can use a 24-inch long 2x4
to lever the washer into place.
6. With the washer in its final position, place a level on top of the washer
(if the washer is installed under a counter, the washer should not be
able to rock). Adjust the front leveling legs up or down to ensure the
washer
is resting solid. Turn the lock
nuts on each leg up towards the
base of the washer and snug with a wrench.
NOTE: Keep the leg extension at a minimum to prevent excessive
vibration. The farther out the legs are extended, the more the washer
will vibrate.
If the floor is not level or is damaged, you may have to extend the rear
leveling legs.
7. Attach the U-shaped hose guide to the end of the drain hose. Place
the hose in a laundry tub or standpipe and secure it with the cable tie
provided in the enclosure package.
Troubleshooting
8. Plug the power cord into a grounded outlet.
9. Turn on the power at the circuit breaker/fuse box.
10. Read the rest of this Owner’s Manual. It contains valuable and helpful
11. Before starting the washer, check to make sure:
12
Cable
Tie
Cable
Tie
Cable
NOTE: Placing the drain hose too far down the drain pipe can cause a
siphoning action. No more than 7 inch (17.78 cm) of hose should be in
the drain pipe. There must be an air gap around the drain hose. A snug
fit can also cause a siphoning action.
NOTE: Check to be sure the power is off at the circuit breaker/fuse box
before plugging the power cord into an outlet.
information that will save you time and money.
Main power is turned on.
•
The washer is plugged in.
•
The water faucets are turned on.
•
The unit is level and all four leveling legs are firmly in the floor.
•
•
The shipping support hardware is removed and saved.
The drain hose is properly tied up.
•
12. Run the washer through a complete cycle.
13. If your washer does not operate, please review the Before You Call For
Service section before calling for service.
14. Place these instructions in a location near the washer for future
reference.
Safety
Washer
WASHER USE
CONTROL PANEL
6
Requirements
Operation
Instructions
Installation
-
Washer Use Washer Care
Troubleshooting
13
Washer
Safety
Requirements
Operation
Instructions
Installation
Washer Use Washer Care
QUICK START
Press the Power button.
If the screen is dark, a press of the Power
button will “wake up” the display.
Select a wash cycle. (Defaults are set for
each cycle. These default settings can be
changed. See Control setting for more
information).
Press the Pause/Add a Garment button.
CONTROL SETTING
Power
Press to “wake up” the display. If the display is active, press to put
the washer into standby mode.
NOTE: Pressing Power does not disconnect the appliance from the
power supply.
Troubleshooting
14
W ash Cycles
The wash cycles are optimized for specific types of wash loads. The
chart below will help you match the setting with the loads.
Normal/
Colors*
For heavily to lightly soiled colorfast cottons, household
linens, work and play clothes.
NOTE: This is the most common cycle.
Bulky/
Sheets*
Heavy
Duty*
For large items such as comforters, blankets, small rugs
and similar bulky items.
Washing the large and heavy clothing, such as overcoats
or towels.
Whites* For heavily to lightly soiled white laundry, work and play
clothes
Towels* For items such as towels, sheets, pillowcases and dish
rags.
Quick Wash For lightly soiled items needed in a hurry. Cycle time
is approximately 40 minutes, depending on selected
options.
Delicates For delicate, washable textiles, e.g. made of silk, satin,
synthetic fibers or blended fabrics.
Sportswear Washing the activewear.
Tub Clean Use for cleaning the basket of residue and odor.
Recommended use of at least once per month.
NOTE: Never load laundry white using Tub Clean. The
laundry may become damaged See the Care and Cleaning
section.
Rinse &
To quickly rinse and spin out any items at any time.
Spin
Washer
Safety
Requirements
Operation
Instructions
Installation
Washer Use Washer Care
Troubleshooting
15
Washer
Safety
Requirements
Operation
Instructions
Installation
Washer Use Washer Care
SOIL LEVEL
WASH TEMP
Change the Soil level to
increase or decrease the
wash time to remove
different amounts of soil.
Adjust to select the proper
main water temperature
for the wash cycle. The
PreWash rinse water is
always cold to help reduce
energy usage and reduce
setting of stains and
wrinkles.
Follow the fabric
manufacturer’s care label
when selecting the wash
temperature.
To change the Soil level,
press the Soil level button
until you have reached
the desired setting. You
can choose between
Extra Light, Light,
Medium, Heavy or Extra
Heavy soil levels.
To change the wash
temperature, press the
wash Temp button until
you have reached the
desired setting.
You can choose between
Tap Cold,Cold,Eco Warm,
Warm or Hot.
By design, to protect
fabrics, not all wash
temperatures are available
for certain wash cycles.
Troubleshooting
16
SPIN SPEED
Changing the Spin speed
changes the final spin
speed of the cycles.
Always follow the garment
manufacturer’s care label
when changing the Spin
speed.
To change the Spin
speed, press the Spin
speed button until you
have reached the desired
setting. You can choose
between No Spin, Low,
Medium, High or Extra
High. Higher spin speeds
are not available on certain
cycles, such as Delicates.
Higher spin speeds
remove more water from
the clothes and will help
reduce dry time, but may
also increase the possibility
of setting wrinkles on some
fabrics.
SIGNAL
WATER
PLUS
SPEED
WASH
Use the Signal pad to
turn the Signal on or off
all knob turns and button
presses.
Increases the water level
of the main wash.
Option is available on
Normal/Colors,Bulky/
Sheets,Heavy Duty,Whites,
Towels,Delicates,
Sportswear
.
This option reduces the
overall washer cycle time
by optimizing the wash,
rinse and spin actions and/
or gently raising the wash
temperature to get clothes
cleaned faster. Option
is available on Normal/
Colors, Bulky/Sheets,
Heavy Duty, Whites,
Towels or Sportswear
cycles.
Total wash time will vary
based on cycle chosen and
options selected.
Turn Signal on,signal beeps
means it is an acceptable
option,and a double beeps
means not an acceptable
option.
To use:
1. Turn power ON and
select a wash cycle.
2. Select the Add Water
Plus button to activate
water plus.
Press the
3.
button.
To use:
1. Turn power on and
select a wash cycle
which has Speed Wash as
an option.
2. Make any adjustments
to Soil, Temp and Spin
as desired.
3. Press the Speed Wash
button to reduce the
overall wash time.
4.
Press the
button.
Washer
Safety
Requirements
Operation
Instructions
Installation
Washer Use Washer Care
EXTRA
RINSE
This option allows for an
extra rinse during a cycle
to remove excess dirt and
detergent from soiled
loads.
Troubleshooting
17
Safety
Washer
PRE SOAK
For soaking your
garments prior to the
wash cycle.This option
begins with a brief tumble
and then proceeds to
soak the clothes with
water and detergent for a
specified period of time.
Once complete, the cycle
will begin automatically.
Pre Soak must be selected
prior to pressing
button.
The Pre Soak time will add
an additional 10-20 minutes
to the overall wash time.
High-efficiency detergent
from the main wash
compartment in the
dispenser is used for the
Pre Soak period and main
wash cycle.
Requirements
Operation
Instructions
Installation
Washer Use Washer Care
Troubleshooting
EXTRA
RINSE and
PRE SOAK
MY CYCLE
You can lock the controls
to prevent any selections
from being made. Or you
can lock or unlock the
controls after you have
started a cycle.
Children cannot
accidentally start the
washer by touching
buttons with this option
selected.
To save a favorite cycle,
set the desired setting
for wash cycle, soil level,
spin speed and wash temp
settings and hold down
the My Cycle button for
3 seconds, A beep will
sound to indicate the
cycle has been saved.
To use your custom cycle,
press the My Cycle button
before washing a load.
To change the saved cycle,
set the desired setting and
hold down the My Cycle
button for 3 seconds.
To lock the washer, press
and hold the Extra Rinse
and Pre Soak buttons for
3 seconds.
To unlock the washer
controls, press and hold
Extra Rinse and Pre Soak
buttons for 3 seconds.
NOTE: The Power button
can still be used when the
machine is locked.
NOTE: When using My
Cycle, wash options cannot
be modified after the cycle
has been started.
NOTE: If you change wash
options with My Cycle
before starting the cycle,
the My Cycle light will
turn off and you will be
returned to the base cycle.
18
DELAY
You can delay the start
of a wash cycle for up to
24 hours. Press the Delay
Wash button to choose
the amount of time you
want to delay the start of
the wash cycle. Once the
desired time is reached,
press the
button. The
machine will count down
and start automatically at
the correct time.
Press to start a wash
cycle. If the washer is
running,pressing it once
will pause the washer.
Press again to restart the
wash cycle.
If you want add a
garment,please press the
button.
The washer will unlock the
door. Press again to restart
the cycle.
NOTE: If you forget to close
the door, a double beep will
sound when pressing
pause/add garment button.
NOTE: If you open the door
when the delay is counting
down, the machine will
enter the pause state.
You must close the door
and press
button
again in order to restart
the countdown.
NOTE: In some cycles the
washer will drain first,then
unlock the door when it is
paused.
NOTE: The washer
performs automatic system
checks after pressing the
button.
You may hear the door lock
and unlock before water
flows, this is normal.
Washer
Safety
Requirements
Operation
Instructions
Installation
Washer Use Washer Care
Display
Displays the approximate
time remaining until the
end of the cycle.
NOTE: The cycle time
is affected by the water
pressure in your home and
the balance of the load
in the washer. You may
see the time remaining
on the display increase to
accommodate a slower
spin speed to handle
unbalanced loads.
B
C
A
-
Pre
D
Cycle status is also
displayed and certain
features such as Delay
Wash or Steam are shown
indicating they have been
selected.
Display
A
Wash Time Delay Time
End
Remain-Delay
B
Child Lock
C
Door Lock
D
Error
Troubleshooting
19
Washer
Safety
Requirements
Operation
Instructions
Installation
FEATURES
THE DISPENSER DRAWER
Slowly open the dispenser drawer by pulling it out until it stops.
After adding laundry products, slowly close the dispenser drawer. Closing
the drawer too quickly could result in early dispensing of the bleach,
fabric softener or detergent.
You may see water in the dispenser drawer at the end of the cycle. This
is a result of the flushing/siphoning action and is part of the normal
operation of the washer.
Washer Use Washer Care
Troubleshooting
20
•
NOTE: Liquid detergent will drain into the washer drum as it is added.
Detergent usage may need to be adjusted for water temperature,
water hardness, size and soil level of the load. Avoid using too much
detergent in your washer as it can lead to over sudsing and detergent
residue being left on the clothes.
The Detergent Compartment
High-efficient detergent is required for this washer.
•
Use the detergent manufacturer’s recommended amount.
Add measured detergent to the front left detergent compartment of
•
the dispenser drawer.
Remove for powder detergent
Normal
HE Liquid
Detergent
Setting
2X HE Liquid
Detergent Setting
(most common
setting)
3X HE
Liquid
Detergent
Setting
Detergent is flushed from the dispenser at the beginning of the wash
•
1X
2X
3X
LIQUID
DETERGENT
remove for powder
SO
cycle. Either powdered or liquid detergent can be used.
Powder Detergent-Remove the Detergent selection insert and place
•
it in a safe location outside of the washer. Follow the detergent
manufacturer’s instructions when measuring the amount of powder to
use.
Detergent usage may need to be adjusted for water temperature,
•
water hardness, size and soil level of the load. Avoid using too much
detergent in your washer as it can lead to oversudsing and detergent
residue being left on the clothes.
Using more detergent than the recommended quantity can cause
•
residue buildup on your washer.
Liquid Detergent - Locate the concentration of your detergent on
•
the bottle. Place the Detergent selection insert in the corresponding
location depending on the concentration.
Washer
Safety
Requirements
Operation
Instructions
Installation
Washer Use Washer Care
Troubleshooting
21
Washer
Safety
Requirements
Operation
Instructions
Installation
Washer Use Washer Care
The Liquid Bleach Compartment
IMPORTANT: Be sure to identify the correct compartment for bleach
before using.
If desired, measure out the recommended amount of liquid bleach, not
to exceed
cup (80 ml), and pour into the right compartment labeled
1/3
“LIQUID BLEACH”.
Do not exceed the maximum fill line. Overfilling can cause early
dispensing of the bleach which could result in damaged clothes.
NOTE: Do not use powdered bleach in the dispenser.
The Fabric Softener Compartment
IMPORTANT: Be sure to identify the correct compartment for fabric
softener before using.
If desired, pour the recommended amount of liquid fabric softener into
the compartment labeled “FABRIC SOFTENER”.
Troubleshooting
Use only liquid fabric softener in the dispenser.
Dilute with water to the maximum fill line.
Do not exceed the maximum fill line. Overfilling can cause early
dispensing of the fabric softener which could stain clothes.
NOTE: Do not pour fabric softener directly on the wash load.
22
LOADING AND USING THE WASHER
Always follow fabric manufacturer’s care label when laundering.
SORTING WASH LOADS
Sort laundry into loads that can be washed together.
OURS
COL
Whites
Lights
Darks
Combine large and small items in a load. Load large items first. Large
•
items should not be more than half the total wash load.
Washing single items is not recommended. This may cause an out-of-
•
balance load. Add one or two similar items.
Pillows and comforters should not be mixed with other items. This may
•
cause an out-of-balance load.
SOIL FABRIC LINT
Heavy
Normal
Light
Delicates
Easy Care
Sturdy Cottons
Lint
Producers
Lint
Collectors
WARNING
Fire Hazard
Never place items in the washer that are dampened
•
with gasoline or other flammable liquids.
No washer can completely remove oil.
•
Do not dry anything that has ever had any type of oil
•
on it (including cooking oils).
Doing so can result in death, explosion, or fire.
•
PREPARING CLOTHES
To avoid snags during washing:
Follow these steps to maximize garment care.
Close garment zippers, snaps, buttons and hooks.
•
Mend seams, hems, tears.
•
Empty all items from pockets.
•
Remove nonwashable garment accessories such as ornaments and
•
nonwashable trim materials.
To avoid tangling, tie strings, draw ties and belt-like materials.
•
Brush away surface dirt and lint.
•
Promptly wash wet or stained garments to maximize results.
•
Use nylon mesh garment bags to wash small items.
•
Wash multiple garments at one time for best results.
•
Washer
Safety
Requirements
Operation
Instructions
Installation
Washer Use Washer Care
Troubleshooting
23
Safety
LOADING THE WASHER
Wash drum may be fully loaded with loosely added items. Do not wash
fabrics containing flammable materials (waxes, cleaning fluids, etc.).
To add items after washer has started, press and wait until the door
is unlocked. The washer may take up to 30 seconds to unlock the door
after pressing depending on the machine conditions.
Do not try to force open the door when it is locked.
Washer
After the door unlocks, open gently. Add items, close the door and press
to restart.
Requirements
WASHER CARE
Operation
CLEANING
Instructions
Washer Use Washer Care
Troubleshooting
EXTERIOR
Installation
Immediately wipe off any spills. Wipe with damp cloth. Do not hit surface
with sharp objects.
INTERIOR
To clean the interior of the washer, select the Tub Clean feature on the
control panel. This Tub Clean cycle should be performed, at a minimum,
once per month. This cycle will use more water, in addition to bleach, to
control the rate at which soils and detergents may accumulate in your
washer.
NOTE: Read the instructions below completely before starting the Tub
Clean cycle.
1. Remove any garments or objects from the washer and ensure the
2. Open the washer door and pour one cup or 250 ml of liquid bleach or
washer basket is empty.
other washing machine cleaner into the basket.
24
3. Close the door and select the Tub Clean cycle. Push the
button.
4. When the Tub Clean cycle is working, the display will show the
estimated cycle time remaining. The cycle will complete in about
90 minutes. Do not interrupt the cycle.
5. After the cycle is complete, leave the door open slightly for better
ventilation.
If for any reason the cycle needs to be interrupted, the door will not
open immediately. Forcing open the door at this stage may cause water
to flood. The door will open after the water is drained to a level where it
would not flood the floor.
Tub Clean may be interrupted by pressing
A power outage in the house might also
button in between cycles.
interrupt the cycle.When the
power supply is back, the Tub Clean cycle resumes where it had stopped.
When interrupted, be sure to run a complete Tub Clean cycle before
using the washer. If the Power pad is pressed during Tub Clean,the
cycle will be lost.
IMPORTANT:
Run Tub Clean with 1 Cup (250 ml) of bleach once a month.
•
After the completion of a Tub Clean cycle, the interior of your washer
•
may have a bleach smell.
It is recommended to run a light colour load after the Tub Clean cycle.
•
DISPENSER DRAWER AREA
Detergent and fabric softener may build up in the dispenser drawer.
Residue should be removed once or twice a month.
Lock tab is visible only after drawer has been pulled open.
Remove the drawer by first pulling it out until it stops. Then reach back
into the left rear corner of the drawer cavity and press down firmly on
the lock tab, pulling out the drawer.
Washer
Safety
Requirements
Operation
Instructions
Installation
Washer Use Washer Care
Troubleshooting
25
Washer
Safety
Requirements
Operation
Instructions
Installation
Washer Use Washer Care
CLEANING THE PUMP FILTER
Due to the nature of the front-load washer, it is sometimes possible for
small articles to pass to the pump. The washer has a filter to capture lost
items so they are not dumped to the drain. To retrieve lost items, clean out
the pump filter.
Pump lter
1. Using a coin or flat screwdriver in the notch on the door, open the
access door.
2. Place a shallow pan or dish under the pump access door and towels on
Troubleshooting
3. Pull down the pour spout.
26
the floor in front of the washer to protect the floor. It is normal to catch
about a cup of water when the filter is removed.
Pour
spout
Loading...