Midea 24DMS4G109 Instruction Manual

Free-standing gas hotplates and electrical oven

Instruction Manual

24DMS4G109

Thank you for choosing us! Please read all instructions before using
this appliance. This book contains valuable information about
operation, care and service. Keep it in a safe place for future
reference. Should the appliance be sold or transferred to another
owner, or should you move house and leave the appliance, always
ensure that the book is supplied with the appliance so that the new
owner can be acquainted with the functioning of the appliance and
relevant warnings.

Safety Warning

THESE WARNINGS ARE PROVIDED IN THE INTEREST OF
SAFETY, PLEASE READ THEM CAREFULLY BEFORE INSTALLING
OR USING THE APPLIANCE

 To maintain the EFFICIENCY and SAFETY of this appliance, we

commend:

 Call the Service Centers authorized by the store where you buy

the cooker.

 Always use original Spare Parts

1. This appliance is intended for non-professional use within the
home.

2. Before using the appliance, read the instructions in this owner’s
manual carefully, since you should find all the instructions you require
to ensure safe installation, use and maintenance. Always keep this
owner’s manual close to hand since you may need to refer to it in the
future.

3. After removing the packaging, check that the appliance is not
damaged. If you have any doubt, do not use the appliance. Contact
your nearest Service Centre of the store where you buy the appliance.
Never leave the packaging components plastic bags ， foamed
polystyrene， nails, etc. ) within the reach of children since they are a
source of potential danger.

4. The appliance must be installed only by a qualified person in
compliance with the instructions provided. The manufacturer declines
all responsibility for improper installation which may harm persons and
animals and damage property.

5. This appliance designed to be used by children aged above 8 years.
Person with reduced physical, sensory or mental capabilities or lack of
experience and knowledge shall be under supervision and instructed
concerning use of the appliances in a safe way and understand the
hazards involved when using the appliance.

6. The electrical safety of this appliance can only be guaranteed if the
cooker is correctly and efficiently earthed, in compliance with current
regulations on electrical safety. Always ensure that the earthing is

2

Important

7. Check that the electrical capacity of the system and sockets will
support the maximum power of the hob, as indicated on the rating
label. If you have any doubts call in a qualified technician

8. When the cooker is first used an odor may be emitted, this will
cease after a period of use. When first using the cooker ensure that
the room is well ventilated e.g., open a window or use an extractor fan
and that persons who may be sensitive to the odor avoid any fumes. It
is suggested that any pets be removed from the room until the smell
has ceased. This odor is due to temporary finish on oven liners and
element sandal so any moisture absorbed by the insulation.

9. Ensure that the appliance is switched off before maintenance by
switching off the main switches and turning all knobs to OFF position.

10. The openings and slots used for ventilation and dispersion of heat
on the rear and below the control panel must never be covered.

11. The user must not replace the supply cable of this appliance.
Always call an after-sales servicing Centre authorized by the seller in
the case of cable damage or replacement.

12. This appliance must be used for the purpose for which it was
expressly designed. Any other use is considered to be improper and
consequently dangerous. The manufacturer declines all responsibility
for damage resulting from improper and irresponsible use.

13. A number of fundamental rules must be followed when using
electrical appliances. The following are of particular importance do not
touch the appliance you’re your hands or feet are wet do not use the
appliance bare footed. Never allow the Mains Cable to be stretched,
pulled or damaged if the Cooker is moved for cleaning etc. Do not use
the cooker if the Mains Cable is damaged, consult a qualified
electrician. Do not allow the cooker to be used unsupervised by
children or persons unfamiliar with it.

14. Always switch off the electrical supply to the cooker and allow it to
cool down before carrying out any cleaning operations etc.

15. Danger of fire: do not store items on the cooker surfaces.

16. To avoid accidental spillage do not use cookware with uneven or
deformed bottoms on the burners or on the electric plates.

17. Special care should be taken when using chip pans etc. in order to
avoid splashing or spillage of hot oil. They should not be used
unattended since over heated oil may boil over and could also ignite.

18. Parts of this appliance, cooking surfaces, retain heat for
considerable periods after switching off. Care should, therefore, be
taken when touching these areas before they have completely cooled

down.

3

efficient if you have any doubts call in a qualified electrician to check
the system. The manufacturer declines all responsibility for damage
resulting from a system which has not been earthed.

21. Make sure the knobs are in its “OFF” position when the appliance
is not in use. Also make all potentially dangerous parts of the
appliance, safe, above all for children who could play with the
appliance.

22. When the appliance is in use the heating elements and some parts
of the oven door become extremely hot. Make sure you don’t touch
them and keep children well away.

23. If you use the power cable for single phase, the minimum
cross-sectional area is 10mm2. For three phases the minimum cross
sectional area is 2.5 mm²

24.You must grill with closed door.

25. DO NOT USE OR STORE FLAMMABLE MATERIALS IN THE
APPLIANCE STORAGE DRAWER OR NEAR THIS APPLIANCE.
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS
APPLIANCE WHILE IT IS IN OPERATION.

26. DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.

27. DO NOT MODIFY THIS APPLIANCE.

28. DO NOT USE THIS APPLIANCE AS A SPACE HEATER.

29.

Gas installation must be made in accordance with AS/NZS 5601.

Also refer to rangehood manufacturers recommendation.

30.

Special conditions which shall be avoided, e.g. marine

environment, and any conditions necessary to ensure optimum
performance.

31. Where necessary, a safe purge before the appliance is re-lit.

Safety

For the user and installer

1. Disconnect the range before cleaning or doing maintenance.

2. Never unplug the range by pulling on the power cord. Do not
manipulate your gas range plug. Do not bite, twist or tie the power
cord.

3.

It is dangerous to modify your gas range specifications and
characteristics.
Do not install your gas range on top of the power cord.

4. Connect the range to its own outlet. Do not use an extension cord
or adaptor plug. To avoid any accident, before replacing the light
lamp, turn off the cook top burners

4

19. Never use flammable liquids such as alcohol or gasoline, etc. near

the appliance when it is in use.

20. When using small electrical appliances near the hob, keep the

supply cord away from the hot parts.

Care with food and cookware

1. To handle or remove food, please use the cooking gloves.

2. Never leave clothes or flammable materials near the burner when

the range is in use. When using frying oil or butter additional care
must be taken since these products are flammable.

3. Do not use the oven to store utensils, especially those containing

residues or large quantities of oil or fat.

4. Containers with curved bases or salient edges must not be used

since they can be easily destabilized when moved.

5. The handle of the utensil should be positioned so that it is turned

inward.

5

Anti-tilt Bracket

To prevent tipping

of the cooker.

Free-standing gas hotplates and electrical oven

Pressure test

connector

(For ULPG)

1

Test gas pressure

24DMS4G109

For grill, dishes,
cake pan with items
for

roasting and

grilling.

Wire shelf

6

Univeral pan

For cooking large
quantities of food

such

as moist cakes,

pastries, frozen food
etc,or for collecting

fat/ spillage and meat
juices.

Baking and

roasting

shelf

For ovenware, cake tins,
roasts, grilling and frozen
meals.

Slider bracket

These shelf support

rails on the right and
left

sides of the oven

can be removed for

cleaning oven walls.

Legs

7

Before installing

Read the following information about the appliance and the guidelines
for ventilation.

Appliance Unpacking

Check the condition of the appliance after unpacking it.
Do not connect the appliance if it has been damaged in transport.
Dispose of packaging in an environmentally-friendly manner.

Guideline for ventilation

This appliance may only be set up in a sufficiently ventilated room and
according to the applicable regulations and ventilation requirements.
Ventilation must be in accordance with AS/NZS 5601 - Gas
Installations.
Be sure that there is a good air flow, keeping natural air ventilation
through a window or door by installing a range hood to extract the air. If
ventilation is not good, this might cause lack of oxygen, which is
dangerous for your health and the gas performance. If the gas range
will be working for a long period of

time, a extra ventilation will be
necessary to increase the air flow.
Do not install in a bed-sitting room, a bathroom or shower room.
If there is another fuel burning appliance in the same room, a higher
level of ventilation will be required.
In addition to the above, during prolonged use, opening a window in
the same room is recommended. This will avoid the build up of
excessive moisture and condensation.

Installation

This appliance is always supplied with a set of adjustable feet and,
depending on the model, with a
splash guard.The appliance may also be used without the splash
guard.

Installing instruction

8

supports and burners.

• Remove the accessories from the oven.Proceed as follows:

• Tilt the appliance by raising one side slightly from the floor.

• With the plates in position, screw the adjustable feet into the
mounting holes on the underneath of the appliance.

• Repeat the process on the other side.You can make the final
adjustments to the feet in order to level the appliance once the gas
and electricity supply have been connected. If it is necessary to pull
the appliance, screw the adjustable feet in fully. Make the final settings
only when the other installation tasks have been completed.

In order to prevent tipping of the appliance, this stabilizing means
must be installed. Using ground screw 2 to mount the anti-title bracket
1 on the ground showed as the below picture .

Fitting the adjustable feet Before hand:

•

Remove all parts that are not permanently fixed, especially the pan

1. Anti-title bracket 2.Ground screw

Product Model Height(mm) A(mm) B(mm)

20 850 50 50

9

Gas appliance installation

1> Leave at least 80 to 85cm between
the top of the gas appliance and any
cabinet or appliance hood install above
prepared to be installed built in.
2>Leave at least 5cm in the back and
2cm each side of the gas appliance to
allow the heat to get out.
3>When installing the oven, be sure

not to block the oven exhaust port.

Electrical connection

Only a licensed expert may connect the appliance.The appliance must
be installed according to the most recent IEE regulations (Institute of
Electrical Engineers).The appliance could become damaged if
incorrectly connected.Make sure the voltage of the power supply
corresponds to the specified value on the rating plate. The rating plate
can be found on the inside of the storage compartment flap.Ensure
that the power supply is properly earthed and that the fuse and the
wiring and piping system in the building can withstand the load from
the appliance. It is recommended that you configure the circuit for the
appliance to 16 A. When you route the mains cable, make sure that:

• the cable is not trapped or squashed.

• the cable does not come into contact with sharp edges or cutting
edges.

• the cable does not come into contact with parts that can reach
temperatures of more than 50 °C above room temperature.

Connecting the mains cable

Where the appliance is directly connected to the power supply, an
all-pole isolating switch with a contact gap is required.Complete
disconnection in compliance with the conditions specified in
overvoltage category III must be guaranteed.The earth cable is
excluded from this.

80 to 85cm

5cm

10

The appliance must be connected in accordance with the currently
applicable regulations. Before installing the appliance, check that the
local conditions (type of gas and pressure) are compatible with the

appliance settings. The permissible appliance settings can be found
on the rating plate.Connection to the gas lines and seal fitting must be
carried out professionally according to the currently applicable
standards.

Gas connection on the appliance

The gas connection is located at the rear left of the appliance.
Connecting pieces

NG corrugated tube union(and seal)

Gas connection

An inlet manifold extension pipe must be fitted to the appliance.
Ensure that the pipe is connected using the washer provided and
that the bracket is screwed to the appliance as shown in the
diagram below.
Fit the supplied pressure regulator (for Natural gas) using the NG
test point adaptor and washer to the inlet manifold. Ensure the
arrow is pointing towards the appliance and that pressure testpoint
is accessible from the final position.
Push the cooker back and install the anti-tilt bracket.
Connect the appliance to the consumer piping outlet using only
fixed piping.
This final connection is made when the product is pushed back into
position by access under the cooker.

11

4 burner models: set the burner pressure to 2.75kPa for ULPG, set
the burner pressure to 1kPa for Natural Gas. For commissioning of
the appliance with the regulator for Natural Gas, the test point
pressure should be 1.00kPa with all burners operating on HIGH.
Apply a manometer to the test nipple and reset the regulator if
necessary. Do not forget to replace the test nipple screw and to leave
the instruction book with the user.

Test point for ULPG gas

WARNING:
This appliance has to be installed as per AS/NZS 5601 and if a hose
connectino is made, hose assembly must:

1) Be certified as conforming with AS/NZS 1869, and be Class B or
Class D.

2) Diameter 10mm (minimun).

3) Length 1000mm (maximum).

WARNING:
Ensure hose assembly is restrained from accidental contact with
the flue outlet of an under bench oven.

The hose assembly should be kept clear of the floor when the
appliance is in the installed position.

Test point for Natural gas

12

Safety valve

The installation of a safety valve for opening and closing the gas
supply is a compulsory requirement. Fit the safety valve between the
gas connecting line to the appropriate room and the hob. Ensure
unhindered access to this valve.

Checking for leaks

After connecting the gas line, check the connections for leaks using
soapy water.

Initial use

Switch the appliance on as described in the instruction manual. Light
all the burners and check that the flames remain stable at both the
high and low settings.

Converting the gas type

If the appliance is not already set up for the existing type of gas, the
appliance must be converted. The conversion to a different type of

gas must be carried out by an authorised expert in accordance with
the applicable regulations.
In order to convert to a different type of gas, the nozzles must be
replaced and the low flame and primary air may have to be adjusted.

13

Replacing the nozzles (Hotplate burners)

1. Remove the burner caps （A）and burner（B）from the burners（C）.

2. Remove the nozzle (D) and replace it with an appropriate nozzle for the new type
of gas.

3. Replace the gas label with the new gas label that was supplied with the nozzle set.

4. Place each burner cup(B) on the burner(C).

Setting the minimum flow

1. Switch on the gas burner.

2. Turn the control knob for the gas burner towards the small flame setting

3. Remove the control knob for the gas burner.

4.

Adjust the internal setting screw until as table flame is burning correctly. Loosen

the adjuster screw to increase the gas flow or tighten it to decrease the gas flow.

Check that the flame does not go out when the gas flow is quickly changed between
maximum and minimum, and vice versa. The setting is correct when the height of the
small flame is approx. 3 to 4mm.

14

Positioning and leveling

Positioning the appliance

When installing the appliance, make sure that there is enough space
in the final installation location to pull the appliance forwards for
cleaning and maintenance work. The ground underneath must be
hard and stable. The wall immediately behind the appliance must be
made from non-flammable material, e.g. tiles. If you need to pull the
appliance in order to position it, make sure that the adjustable feet are
screwed in fully.

Levelling the appliance

Level the appliance once all other work has been completed. To do
this, turn the adjustable feet.

15

Using instruction

Your new appliance

Get to know your appliance. You will find information about the control
panel and hob, as well as the oven, types of heating and accessories.

1

2

3

4

5

6

7

8

9

10

1. Pot rack

2. Burners knobs

3. Timer knob

4. Function knob

5. Temperature knob

6. Baking rack

7. Oven door

8. Door handle

9. Ignition Switch (for some models)

10. Base

16

The control panel

The hob

Control knobs for gas burners
Adjust the heat setting of the gas burners using the control knobs. The
symbol above the control knob shows you to which gas burner the
control knob belongs.

Control knobs
Gas burners

Timer

Control knobs
Oven function

Electricigniter-burners

Control knobs
Oven temperature

17

(for some models are auto-ignition)

Operating gas burners

Make sure that the burner lid always sits exactly on top of the burner
cup. The slots on the burner cup must be open. All parts must be dry.

Switching on the gas burner

1.

Press the control knob for the required burner and turn it to position

. The gas burner ignites. Keep the control knob pressed for a

few seconds until the flame stabilises. And push the ignition button

at the same time（for some models are auto-ignition).

2. Adjust the burner to the desired flame setting.

lowest flame setting

highest flame setting

Steam outlet
Risk of burns.

Hot air from the oven escapes out of the steam outlet on the hob.
Never touch the steam outlet. Please note that, in the case of
appliances with a hob cover, the burners in the oven may also only be
switched on if the hob cover is open.

Function button for ignition

Ignition can be manual or auto.

Control knob for oven

Use this control knob to the function

Off

*Shut down where incorrect procedures can result in a hazardous
condition.

18

Symbol

Power

Function

25 The lamp work

58 The lamp and circulation motor work

2600

The top heating element ,grill heating element,
circulation motor ,lamp work

2580

The top heating element ,grill heating element,

circulation motor ,lamp work

1629

The grill heating element, lamp work

2108

The top heating element, bottom heating

element ,lamp and circulation motor work

2075

The top heating element, bottom heating element

and lamp work

1125 The bottom heating element and lamp work

2058

The turbo heating element, lamp and circulation

motor work

And then, use this control knob to the temperature

Baking

OFF

Oven electric on,the minimum temperature

Oven electric on, temperature
Oven electric on，the maximum temperature

50 – 200
Broil

There is a limit stop between settings 250 and 0.
Do not turn the knob beyond this point.

Operate your oven

Please note that, in the case of appliances with a hob cover, the
burners in the oven may only be switched on if the hob cover is open.

19

Switching on the oven lighting

Press down the function button for the oven lighting until it locks into
place.The oven lighting switches on.

Switching off the oven lighting

Press down the function button for the oven lighting until it
releases.The oven lighting switches off.

Oven Control

The oven temperature setting knob can only be rotated clockwise
from the OFF position. Turn oven function control knob to select the
cooking function, meanwhile turn the timer (for the model with timer)
to set the cooking time you want. Then turn oven temperature control
clockwise to the required oven temperature. The red oven
temperature pilot light will immediately illuminate and will
automatically go off when oven temperature reaches the temperature
setting.

The minute minder is a countdown timer which emits an audible signal

when the cooking time has elapsed. The minute minder runs
independently of the oven.

Control knob for minute minder

Off

20 - 120

Cooking time in minutes

Setting a cooking time

Turn the control knob once round clockwise, as far as the limit stop,
and then turn it anti-clockwise to set it to the required time.

The cooking time has elapsed

A signal sounds once the time has elapsed.

The minute minder

20

Accessories

The accessories can be inserted in the oven in 5 different shelf
positions. You can pull the accessories two-thirds of the way out
without them tipping. This allows meals to be removed easily. You can
buy accessories from the after-sales service or from specialist
retailers.

Baking and roasting shelf

For ovenware, cake tins,
roasts, grilling and frozen
meals.

Enamelled baking tray

For moist cakes, pastries,
frozen meals and large
roasts. Can also be
inserted underneath the
wire rack or rotary spit and
used as a drip tray to
collect fat.

Accessory Description

21

The storage compartment (for some models)

Open the storage compartment by folding down the fascia panel.This
compartment can be used to store food or other things.

Risk of fire.

Never leave combustible items in the storage compartment.

Before using for the first time

Please read the following instructions before using your appliance for

the first time. Remove the appliance packaging and dispose of this
appropriately.

Cooking compartment initial cleaning

Remove the accessories from the cooking compartment. Completely
remove any leftover packaging, e.g. small pieces of polystyrene, from
the cooking compartment. Some parts are covered with a protective
film. Remove this film.

1. Clean the outside of the appliance with a soft, damp cloth.

2. If the hook-in racks have already been fitted, unhook and remove
them. For information on removing the racks, see the

section “Removing and refitting hook-in racks.”

3. Clean the cooking compartment with warm soapy water.

Rinsing cooking compartment after initial cleaning

Clean the cooking compartment with hot soapy water. Refit the
hook-in racks.

22

Cleaning the burner lids and cups

Proceed as follows:

1. Clean the burner lids (A) and cups (B) with water and washing-up

liquid.

2. Dry the parts off well.

3. Place the burner sprayer (B) on the burner (C).

4. Place the burner lid (A) exactly on top of the burner cup (B).

Cleaning accessories

Before using the accessories, clean them thoroughly using a cloth and
warm soapy water.

Cleaning the interior glass of the oven

The interior glass of the oven door can be removed: with the door in
the semi-open position, use both hands to remove the glass .After
cleaning, refit the glass in reverse order.
Note: In some models, the glass is screen printed. In this case, when
refitting the glass make sure the screen printed part is legible when
the oven door is opened.

23

Warning

Never use high-pressure cleaners or steam jets.

Risk of short circuit.

Never use caustic or abrasive cleaning agents. These could damage
the surface. If such an agent gets on the front of the appliance, wipe it
off immediately with water. Do not clean any surfaces of the appliance
while they are hot.

Removing and fitting the appliance door

You can remove the appliance door for easier cleaning.
The hinges of the appliance door are each secured by a locking lever.
When the locking lever is folded in (A), the appliance door is secured.
It cannot be unhinged. If the locking lever is open (B), only the hinge is
secured, and you can remove the appliance door.

Risk of injury.

Do not reach inside the hinge.

Removing the appliance door

Proceed as follows:

1. Open the appliance door.

24

2. Lift up the locking levers on both sides.

3.

Close the appliance door until you feel resistance at an angle of
around 15° (in relation to the closed appliance door).

4. Grip the door on either side with both hands.

5. Close the appliance door a little further.

6.

Lift the door upwards and at an angle to remove it.
Do not disassemble the door.

Fitting the appliance door

1. Hold the appliance door at an angle.

2. Insert both hinges, left and right, into the supports.

3. Position the door so that the hinge grooves engage on both sides.

4. Open the appliance door.

5. Fold in the locking levers on both sides.

6. Close the appliance door.

25

Removing and inserting the hook-in racks

You can remove the hook-in racks in order to clean them
separately.The hook-in racks are all fixed to the walls of the cooking
compartment at four points.

Removing the hook-in racks

To remove the hook-in racks, proceed as follows:

1. Undo the screw on the bottom the hook-in rack. The lower hooks of

the hook-in rack are released.

2. Take hold of the top of the hook-in rack and screw on the screw on

the bottom the hook-in rack again.

Replacing the oven light bulb

If the oven light bulb fails, it must be replaced. Replacement
heat-resistant bulbs can be obtained from the after-sales service or
from specialist retailers. Please specify the SN number of your
appliance. Do not use any other type of bulb.
Proceed as follows:

1. Switch off the relevant circuit breaker.

2. Open the appliance door.

3. Lay a tea towel in the cooking compartment if it is cold to prevent
damage.

4.

Unscrew the glass cover from the bulb inside the cooking

compartment by turning it anti-clockwise.

5. Replace the bulb with one of the same type.

Voltage: 230 V Power: 25 W Thread: E14
Temperature resistance: 300°C

26

6. Screw on the glass cover again.

7. Remove the tea towel and switch the circuit breaker back on.

Press the function button the oven lighting until it locks into place in
order to check whether the oven lighting is working properly.

Aftersales service

Our after-sales service is there for you if your appliance needs to be
repaired. You will find the address and telephone number of your
nearest after-sales service centre in the phone book. The after-sales
service centres listed will also be happy to give you the details of an
after-sales service point near you.

27

Switch

Switch

Technical data

28

PRODUCT

GAS/ELECTRIC COOKER

MODEL NO.

VOLTAGE/FREQUENCY

220-240V,50/60Hz

ELECTRIC POWER 3.0kW

TYPES OF GAS

Natural Gas

GAS PRESSURE

1.0 kPa

TOTAL HEAT INPUT

29.2MJ/h 772l/h（hotplate burners）

INJECTOR SIZE

A:1.2mm 7.1MJ/h B: 1.2mm 7.1MJ/h

C: 1.5mm 11.0MJ/h D: 0.9mm 4.0MJ/h

24DMS4G109

Problem solver

Any of the following are considered to be abnormal operation and
may require servicing:
Yellow tipping of the hob burner flame.
Sooting up of cooking utensils.
Burners not igniting properly.
Burners failing to remain alight.
Burners extinguished by oven door.
Gas valves, which are difficult to turn.

Your Installer should be contacted if you have any problems with the
installation.
Before you call a service engineer please check if the problem is
something you could fix yourself. The cause of the problem is often a
simple one.

<Destination country warning >
These instructions are only valid if the country symbol appears on the appliance.
If the symbol does not appear on the appliance, it is necessary to refer to the technical
instructions which will provide the necessary instructions concerning modification of the
appliance to the conditions of use of the country

Container table (use flat-buttom saucepans)

Burner

min Saucepan(mm)

Max Saucepan(mm)

A

120

200

B

120

200

C

200

230

D

80

160

29

Burner does not ignite
Do the burners spark when you press the ignition button? If not is the
power on? See 'Checking the power supply' section further on. If the
power supply is OK then there is probably something wrong with the
ignition system.
Are the electrode or burner slots blocked by debris?
Is the burner dirty or damp? Try cleaning and/or drying the burner.
Is the burner trim correctly located?
Are the burner caps correctly located?
Check that there is not a problem with your gas supply. You can do
this by making sure that other gas appliances you may have are
working.

Pan supports
Aluminium pans may cause a metallic marking on the pan supports
which does not affect the durability of the enamel and may be cleaned
off with a metal cleaner such as 'Brasso'.

Checking the power supply
First check if the main house fuse or circuit breaker has activated.
If it's OK, test the power socket with another appliance. If the other
appliance works, then unplug the cooker and contact the service
agent.

Power Failure
In the event of a failure in the electrical supply the hotplate burners
may be lit using a match.

Ventilation
The use of a gas cooking appliance results in the production of heat
and moisture in the room in which it is installed. Ensure that the
kitchen is well ventilated: keep natural ventilation holes open or install
a mechanical ventilation device, (mechanical extractor hood).
Prolonged intensive use of the appliance may call for additional
ventilation, for example opening a window, or more effective
ventilation, for example increasing the level of mechanical ventilation
where present. For more detail see the Installation Instructions.

THINGS TO TRY BEFORE CALLING FOR SERVICE

Burner does not burn well
Is the burner dirty or damp? Try cleaning and/or drying the burner.
Appliance not suitable for your gas type? Check the identification
plate on the hotplate base.

30

P/N:16171100A23990

OVEN DOES NOT WORK AT ALL
First, when the oven is equipped with timer, check appliance is not
programmed to turn on later. If it is, turn to manual setting (i.e. hand
symbol). If the button or scale on the timer remains in the automatic
position after use, the power supply to the oven will be interrupted.
Also, check your appliance is switched on at the mains. Next check
for an unexpected power strike by switching on adjacent lights etc.
Finally, check fuses and plug wiring. If all these prove satisfactory,
call for service.

LIGHT BULB DOESN'T COME ON
Check bulb for looseness or burnt out bulb.
Note: bulb replacement is not covered by your guarantee.

SMOKE COMING FROM OVEN
If oven is still relatively new, this problem is invariably due to
protective oil on elements. Otherwise, the answer may be oil or fat
which has become deposited on the elements during cooking. In
either event, continued use should burn away the residues. On future
occasions, try to shield food with foil or keep it further away from
element, particularly when grilling.

CLOCKTIMER DOES NOT WORK
Check the cord is plugged into outlet completely.
Check for a blown fuse or tripped circuit breaker.
Check for power outage.
Check step by step operating Instructions on previous pages.

If, after checking through this section, you cannot resolve your
problem please call the number on the warranty page in this manual
for service and spare parts.
When ordering please quote the appliance name, the colour variant
and serial number.
This information can be found on the data plate sealed inside the front
appliance drawer.

31

Maintenance schedule:

To ensure the appliance continues to operate at peak performance,

we recommend a routine service call every 2 years for the life of the

appliance.

FOR SPARE PARTS OR TO FIND THE ADDRESS OF

YOUR NEAREST STATE SPARE PARTS CENTRE IN NEW ZEALAND

JH Electrical and Appliance Ltd

Unit A3/570 mt wellington highway, mt wellington, Auckland

Suburb/City: Auckland

Postcode:1062

Telephone: [phone]