Instruction Sheet
SFR Series
Swing Frame rack
THANK YOU
Thank you for purchasing the SFR Series Swing Frame Rack. Please read these instructions
thoroughly before installing/assembling this product.
PRODUCT FEATURES
- Open back design can be mounted over existing conduit or equipment
- Heavy-duty 100 lb. weight capacity; will not sag when properly installed
- Swinging rack can be reversed to open to either side
I-00040 Rev G
PARTS
MOUNTING PLATE
BRACE
NOTE: SFR-XX-12 models have specific top and bottom
braces. The top brace is labeled
QTY
1
QTY
2
PART
PART
GATE
A
HARDWARE KIT 91-00183
BRACE SCREWS
C
PIVOT BOLTS
QTY
1
QTY
2
QTY
2
PART
B
PART
D
PART
E
DIMENSIONS
NOTE: The multiple dimensions shown are in the following format: SFR-XX-12/SFR-XX-18/SFR-XX-24
45º Open Position
Component
depth
10”
16”
22”
20.7”
25.0"
29.2”
Minimum clearance
required when using 12”,16" or 22”
deep components
Maximum Open Position
29.67"
35.67"
41.67"
90
16" Mounting
12.2"
18.2"
24.2"
0
Closed Position
center
19.6"
Page 2
TOOLS REQUIRED
- 3/8" Wrench or #3 Phillips Driver (FOR PART D)
- 9/16" Wrench (FOR PART E)
- Level
- Square
INSTALLATION
NOTE: All hardware is to be supplied by the
customer unless otherwise specified
1) Determine swing of the rack prior to installation.
2) Secure mounting plate (A) to wall using
the top keyhole. (FIGURE A)
TOP
KEYHOLE
LEVEL
FIGURE A
3) Level mounting plate. (FIGURE B)
FIGURE B
Page 3
INSTALLATION (CONTINUED)
4) Install hardware in bottom keyhole.
(FIGURE C)
5) Install hardware in center keyhole.
(FIGURE C)
CENTER
KEYHOLE
FIXED HOLE
6)
for extra stability.
(FIGURE D)
BOTTOM
KEYHOLE
FIGURE C
Install hardware in fixed holes
FIGURE D
FIXED HOLE
Page 4
INSTALLATION (CONTINUED)
D
FIGURE F
7) Install top brace (C) to mounting plate (A)
using brace screw (D). (FIGURE E)
IMPORTANT NOTE: SFR-XX-12 top brace (labeled top) must have the
three holes facing the mounting plate to ensure proper installation
(FIGURE F)
FIGURE E
D
C
A
SQUARE
8) Square mounting plate. (FIGURE G)
9) Install top brace to wall.
FIGURE G
Page 5
INSTALLATION (CONTINUED)
10) Install bottom brace (C) to mounting plate (A)
using brace screw (D). (FIGURE H)
IMPORTANT NOTE: The SFR-XX-12 bottom brace must have the three holes
facing the mounting plate to ensure proper installation (FIGURE J)
A
C
FIGURE J
D
FIGURE H
11) Square mounting plate. (FIGURE K)
12) Install bottom brace to wall.
D
SQUARE
FIGURE K
Page 6
INSTALLATION (CONTINUED)
NOTE: Rackrail on gate (B) must face out
13) Install gate (B) to mounting plate (A)
using pivot bolts (E). (FIGURE L)
E
IMPORTANT NOTE: Tighten pivot bolts (E). DO NOT OVERTIGHTEN
E
B
FIGURE L
FIGURE M
Page 7
LATCH
NOTE:
on the top and bottom (FIGURE M)
Gate latches to the mounting plate
WARRANTY
Middle Atlantic Products, (the "Company") warrants the SFR Series Swing Frame Rack
to be free from defects in material or workmanship under normal use and conditions for
the lifetime of the product.
The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and
exclusive remedy, under this warranty shall be limited, at the Company's option, to either (a) return
of and refund of the price paid for, or (b) repair or replacement at the Company's factory of the
products purchased, or any part or parts thereof, which the Company has determined to be
defective after inspection thereof at the Company's factory.
This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by
parties other than the Company, or any modification or alteration of the products. In addition, this
warranty does not cover damage due to improper handling, assembly, installation or maintenance.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY
BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES
WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF THE
PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY)
HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS
PAID TO THE COMPANY.
Corporate Headquarters
Corporate Voice 973-839-1011 - Fax 973-839-1976
International Voice +1 973-839-1011 - Fax +1 973-831-4982
middleatlantic.com - info@middleatlantic.com
Middle Atlantic Canada
Voice 613-836-2501 - Fax 613-836-2690
middleatlantic.ca - customerservicecanada@middleatlantic.ca
Factory Distribution
USA: NJ - CA - IL Canada: ON - BC
At Middle Atlantic Products we are always listening. Your comments are welcome.
Middle Atlantic Products is an ISO 9001 Registered Company.
Page 8
30% Recycled Paper
Loading...