Instruction Sheet
BRK/RK SERIES
Black Laminate Rack
THANK YOU
Thank you for purchasing the BRK/RK Series Black Laminate Rack. Please read
these instructions thoroughly before assembling this product.
PRODUCT FEATURES
- Sturdy design
- Easy to assemble
- Multiple options for full customization
I-1101 Rev E
PARTS
TOP/BOTTOM (QTY - 2)
(Top and Bottom are interchangeable)
SIDE (QTY - 2)
(Sides are interchangeable)
STICK ON BUMPER
(QTY - 5 - One Extra)
TOOLS REQUIRED
4 MM HEX BIT (Included)
4 MM HEX KEY (Included)
JOINT CONNECTOR SCREW
(QTY - 12)
SCREW CAP
(QTY - 12)
#2 PHILLIPS DRIVER (for options only)
Page 2
DETERMINE OPTIONS BEFORE BEGINNING ASSEMBLY
_
Casters, Part # - RKW
_
Quick-Position™ Shelf , Part # - SH-BRK (BRK Models only, cannot be installed with front or
rear rackrail in the 3rd setback location - see below)
_
P ower Strip, refer to our catalog or middleatlantic.com for a complete listing
_
Rear rackrail, Part # - RK-RRxx
_
Smoked, tempered glass door, Part # - RK-GDxx
_
Rear Access Panel, Part # - RK-RAPxx (Not available for 6 space racks)
_
100 CFM DC Fan Kit, Part # - DCFANKIT-4.
(Options not available for RK2 and RK4 models)
ASSEMBLY
1) Lay out the sides as shown and determine rail mounting requirements. The front rackrail comes
pre-installed in mounting location 1.
MOUNTING HOLE
3 2 11 2 3
LOCATIONS
FRONT
TIP:
setback position, relocate and mount
the rail on the opposite side of the
panel to obscure the 1st set of
mounting holes.
When moving the front rackrail to the
- If the Door (RK-GDxx) and the Rear Access
Panel (RK-RAPx) are not being used,
the front and rear rackrail can be installed
in any one of the three mounting locations.
- If the Door (RK-GDxx) and the Rear Access
Panel (RK-RAPx) are being used,
the front rackrail must be installed in
location two and the rear rackrail must be
installed in location three.
Top view showing front rackrail and rear rackrail
installed in location 1
FRONT
Top view showing front rackrail installed in location 2,
and rear rackrail installed in location 3
Top view showing front rackrail and rear rackrail
installed in location 3
IF YOU ARE USING THE REAR RAIL OPTION, INSTALL NOW
Page 3
LEFT
SIDE
OPTIONAL CASTER
(Install non-locking casters
in rear of rack)
2) Position parts as shown.
OPTIONAL
REAR RAIL
JOINT
CONNECTOR
SCREW
SCREW
CAP
RIGHT
SIDE
STICK ON
BUMPER
3) Place rack on its back for
ease of assembly.
4) Assemble rack as shown with the hardware
provided. Tighten screws after all are in place
TIP:
Soap on screw threads eases assembly
when a power driver is not used.
5) Install stick on bumpers when not
using optional casters.
6) Install optional casters with non-locking
casters to the rear (part # RKW).
(FIGURE A
)
7) Assembly is complete. Stand rack upright and
begin installing equipment.
OPTIONAL CASTER INSTALLATION (RKW)
3/4" SET BACK
Mounts directly
over center line
of bolt hole
(4 places)
BOTTOM
SIDE
FIGURE A
Page 4
OPTIONS
Quick-Position™ Shelf (Part # SH-BRK) mounts without rack screws and accepts rear
mounting of power (PD-815SC or PD-815SC-NS).
SH-BRK SHELF
NOTE: Shelves can be used with or without rackrail installed.
NOTE
PD-815SC-NS
shown
(When mounting power
to shelf, optional rear
rackrail must be in setback
location 2. See PAGE 3)
REAR
: Rear Access Pan cannot be used if installing a power strip to the shelf.
Page 5
OPTIONS
Rear Rackrail for equipment support and cable management. Part # RK-RRxx
REAR RACKRAIL
TIP: Rear Rackrail installation is easier prior to assembly of the rack, but
can be installed after assembly if necessary. (SEE
PAGE 3)
1) Three sets of pilot holes
are present. Install Rear
Rackrail as shown with
provided hardware.
WOOD SCREW
THREE PRE-DRILLED
MOUNTING LOCATIONS
DID YOU KNOW?
Rear Rackrail provides support for mounted equipment and a location to mount cable
management products such as Lacer Bars. Part # LBP-XX
Page 6
OPTIONS
Smoked, Tempered Glass Door secures components and enhances appearance, part # RK-GDxx.
RK-GDxx
NOTE: Front Rackrail must be mounted in second setback position, see page 3.
Locking/latching panel, tips out for easy access. Provides cable entry and security, part # RK-RAPxx.
VENTED TOP PANEL
LOCKING/LATCHING PANEL
CABLE MANAGEMENT PANEL
100 CFM DC Fan Kit. Mounts in the top of the Rear Access Panel, part # DCFANKIT-4.
Page 7
WARRANTY
Middle Atlantic Products, Inc. (the "Company") warrants the RK/BRK Series Black Laminate Rack to
be free from defects in material or workmanship under normal use and conditions for a period
of (7) seven years from date of shipment by the Company.
The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and
exclusive remedy, under this warranty shall be limited, at the Company's option, to either (a) return
of and refund of the price paid for, or (b) repair or replacement at the Company's factory of the
products purchased, or any part or parts thereof, which the Company has determined to be
defective after inspection thereof at the Company's factory.
This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by
parties other than the Company, or any modification or alteration of the products. In addition, this
warranty does not cover damage due to improper handling, assembly, installation or maintenance.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY
BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES
WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF THE
PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY)
HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS
PAID TO THE COMPANY.
Corporate Headquarters
Corporate Voice 973-839-1011 - Fax 973-839-1976
International Voice +1 973-839-8821 - Fax +1 973-839-4982
middleatlantic.com - info@middleatlantic.com
Middle Atlantic Canada
Voice 613-836-2501 - Fax 613-836-2690
middleatlantic.ca - contactcanada@middleatlantic.com
Factory Distribution
USA: NJ - CA - IL Canada: ON - BC
At Middle Atlantic Products we are always listening. Your comments are welcome.
Middle Atlantic Products is an ISO 9001 Registered Company.
Page 8
Loading...