Page 1
installation instructions
PCD SERIES
PLASTIC CABLE DUCTS
MOUNTING DUAL CABLE DUCT BETWEEN 2 OR 4 POST RACKS
Using supplied hardware, install Brackets as shown (four places). See FIGURE B for appropriate orientation.
NOTE: Installed Brackets can be used for additional ganging (FIGURE C)
HARDWARE USED
10-32 X .5” SCREW - 4 QTY
10-32 NUT - 4 QTY
(38RU/45RU)
BRACKET - 4 QTY
(51RU)
NOTE: Brackets are pre-installed on one side
Two Screws and Nuts per Bracket
EXISTING BRACKET
ATTACHED TO RACK
(FIGURE B)
INSTALLED BRACKET
FOR GANGING TO
ANOTHER RACK
(FIGURE A)
Available sized Cable Ducts
(FIGURE C)
Front View with existing and installed brackets
I-00464 Rev -
Page 2
MOUNTING SINGLE CABLE DUCT BETWEEN 2 OR 4 POST RACKS
Using supplied hardware, install Brackets as shown (four places). See FIGURE B for appropriate orientation.
NOTE: Installed Brackets can be used for additional ganging (FIGURE C)
HARDWARE USED
10-32 X .5” SCREW - 8 QTY
10-32 NUT - 8 QTY
(38RU/45RU)
NOTE: Brackets are pre-installed on one side
BRACKET - 4 QTY
(51RU)
(FIGURE B)
Rear View showing
Two Screws and Nuts per Bracket
(FIGURE A)
Available sized Cable Ducts
EXISTING BRACKET
ATTACHED TO RACK
Front View with existing and installed brackets
Page 2
INSTALLED BRACKET
FOR GANGING TO
ANOTHER RACK
(FIGURE C)
Page 3
HINGE CLIP AND COVER INSTALLATION
The ‘HINGE CLIP’ connects the COVER to DUCTS, allowing the Cover to swing open and closed for
optimum cable management.
OUTER VIEW
COVER
HINGE CLIP
COVER(S)
1) Slide the ‘hook portion’ of the Hinge Clip onto the Cover as shown. (FIGURE A)
SLIDE CLIP ONTO COVER
HINGE CLIP
FLA
T
portion
FINGER
FINGER
HOOK
portion
COVER
COVER
(Horizontal View)
CLIP
(OUTLINED IN WHITE FOR CLARITY)
FIGURE A
Page 3
Page 4
RECOMMENDED: Space two (2) Hinge Clips three (3) inches from the cover edges, and one additional
clip in the center portion of the cover as shown. (FIGURE B)
Hinge Clip
Cover
3 inches
(FIGURE B)
3 inches
2) Once the clips are attached to the cover, align each clip beside and in-between two fingers. (FIGURE C)
Cover
Hinge Clip
(FIGURE C)
The clips snap into one finger at a time
(FIGURE D)
The Clip is ATTACHED
INNER VIEW
OUTER VIEW
(FIGURE F)
(FIGURE E)
WARRANTY
Middle Atlantic Products, Inc. (the "Company") warrants the Plastic Cable Ducts to be free from defects in material or workmanship under normal use and conditions for the lifetime
of the product.
The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and exclusive remedy, under this warranty shall be limited, at the Company's option, to
either (a) return of and refund of the price paid for, or (b) repair or replacement at the Company's factory of the products purchased, or any part or parts thereof, which the Company
has determined to be defective after inspection thereof at the Company's factory. This warranty does not cover damage due to acts of God,accident, misuse, abuse or negligence by
parties other than the Company, or any modification or alteration of the products. In addition, this warranty does not cover damage due to improper handling, assembly, installation or
maintenance.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR
CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION OR ANY
OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF THE PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY) HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF
THE PRODUCTS PAID TO THE COMPANY.
Corporate Headquarters
Corporate Voice 973-839-1011 - Fax 973-839-1976 / International Voice +1 973-839-8821 - Fax +1 973-839-4982
middleatlantic.com - info@middleatlantic.com
Middle Atlantic Canada
Voice 613-836-2501 - Fax 613-836-2690 / middleatlantic.ca - customerservicecanada@middleatlantic.ca
Factory Distribution
USA: NJ - CA - IL Canada: ON - BC
At Middle Atlantic Products we are always listening. Your comments are welcome.
Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.
Page 4
Loading...