Middle Atlantic LD User Manual

Instruction Sheet

LD SERIES

LCD Monitoring Desk

THANK YOU
Thank you for purchasing the LD Series LCD Monitoring Desk. Please read these instructions
thoroughly before assembling this product.

PRODUCT FEATURES

- Modular Design allows economical additions and limitless design possibilities

- Power distribution and cable management cabinet features integral front door and
rear doors for access

I-00080 Rev K

ASSEMBLY

CAREFULLY REMOVE ALL CONTENTS FROM CRATE BEFORE BEGINNING ASSEMBLY

1) Lay desktop upside down on a flat surface. Using the two screws provided, attach cabinet
to work surface. Do not tighten screws. (

NOTE: For ease of installation, keep desk flipped over until assembly of desk and accessories is
complete.

NOTE: Bottom of desktop has mounting holes for accessories. Bottom of cabinet does not have

Remove the doors from the cabinet during assembly and remove the hole plugs from

TIP:

the back of the cabinet.

FIGURE A)

seloh gnitnuom dna sgulp eloh nehw tcerroc si noitcerid tenibaC .seloh gnitnuom

BOTTOM OF

CABINET

HOLE PLUGS

(HOLE PLUGS LOCATED

ON BACK)

BOTTOM OF

DESKTOP

(FIGURE A)

2) Attach toe kick to cabinet by using three screws provided.
(FIGURE B)

NOTE: Hole plugs from bottom rear of desk can be removed for
easier access to tighten toe kick screws. Remaining hole plugs
from rear can be removed to run cables through or left in place
if not used.

(FIGURE B)

Push in and

Pop Out

HOLE PLUGS

Page 2

ASSEMBLY

3) Identify the right leg and the left leg by referring to labels. Attach legs to the desktop by sliding
the legs into the grooves on the work surface. Install four screws into each leg from the inside of the
cabinet (two on top, two on bottom). Do not tighten. (FIGURE C)

(FIGURE C)

4) Attach support brackets by installing four screws in each bracket. Do not tighten.

NOTE: Sliding nuts are dropped into leg channel and can be positioned into place using a thin tool to
align with holes in mounting bracket. (FIGURE D)

(FIGURE D)

Page 3

SLIDING NUT

(SERRATED SIDE

FACES OUT

FROM INSIDE OF

CHANNEL)

5) Check alignment and gently tap side of leg with rubber mallet to make sure it is in securely
(FIGURE E)

. Tighten all screws.

(FIGURE E)

6) Install leveling feet by screwing into bottom of legs, two on each leg. (FIGURE F). Adjust as needed.

(FIGURE F)

Page 4

INSTALLATION OF OPTIONAL POWER STRIP (SOLD SEPARATELY)

NOTE: Disregard instruction sheet that came with power strip and follow the instructions below.

Middle Atlantic Products recommends the use of the PD-815SC or PD-815SC-NS slim 8 outlet
power strip with the LCD monitoring desk. The desk has been optimized to accommodate up to
two power strips.

1) Install mounting brackets with screws provided with PD-815SC or PD-815SC-NS power strip
using acorn nuts included with desk. (

FIGURE H)

MOUNTING

BRACKETS

2) Attach power strip to mounting bracket by

snapping in place. (FIGURE J)

(FIGURE H)

Page 5

(FIGURE J)

LD-48 (48" DESK): Work Surface Accessory Mounting Points

REAR

15"

PENCIL

TRAY

(D-PT15)

KEYBOARD TRAY (LD-KB)

FRONT

REAR

15"

PENCIL

TRAY

(D-PT15)

PART #

Pencil Tray

(D-PT15, D-PT22)

Keyboard Tray

(LD-KB)

NUMBER OF

MOUNTING HOLES

4

8

KEYBOARD TRAY (LD-KB)

FRONT

NOTE: 22" pencil tray (D-PT22) does not fit on 48" desk (LD-48)

Page 6

LD-64 (64" DESK): Work Surface Accessory Mounting Points

REAR

PART #

Pencil Tray

(D-PT15, D-PT22)

NUMBER OF

MOUNTING HOLES

4

15"

PENCIL

TRAY

(D-PT15)

22"

PENCIL

TRAY

(D-PT22)

FRONT

REAR

22"

PENCIL

TRAY

(D-PT22)

15"

PENCIL

TRAY

(D-PT15)

Keyboard Tray

(LD-KB)

8

22"

PENCIL

TRAY

(D-PT22)

FRONT

REAR

22"

PENCIL

TRAY

(D-PT22)

KEYBOARD TRAY (LD-KB)

FRONT

Page 7

WARRANTY
Middle Atlantic Products, Inc. (the "Company") warrants the LD Series LCD Monitoring Desk to be free
from defects in material or workmanship under normal use and conditions for a period of (3) three years
from date of shipment by the Company.

The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and
exclusive remedy, under this warranty shall be limited, at the Company's option, to either (a) return
of and refund of the price paid for, or (b) repair or replacement at the Company's factory of the
products purchased, or any part or parts thereof, which the Company has determined to be
defective after inspection thereof at the Company's factory.

This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by
parties other than the Company, or any modification or alteration of the products. In addition, this
warranty does not cover damage due to improper handling, assembly, installation or maintenance.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY
BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES
WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE OF THE
PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER PARTY)
HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS
PAID TO THE COMPANY.

Corporate Headquarters
Corporate Voice 973-839-1011 - Fax [phone]
International Voice [phone] - Fax [phone]
middleatlantic.com - [e-mail]

Middle Atlantic Canada
Voice 613-836-2501 - Fax [phone]
middleatlantic.ca - [e-mail]

Factory Distribution
USA: NJ - CA - IL Canada: ON - BC

At Middle Atlantic Products we are always listening. Your comments are welcome.

Middle Atlantic Products is an ISO 9001 and ISO 14001 Registered Company.

Page 8